Triton Blue TR 101 User manual

Triton Blue
TR 101
User manual

2
Manual TR 101 Triton Blue
WWW.TRITON-BLUE.COM
USER MANUAL
TR-101
Read these instructions carefully before use.
 After reading them. Keep them in a safe place for future reference. They will prove
useful later when further information is needed or the air conditioner is not working
properly.
 Bright laser, small in size, and wide in reach, this product offers endless highlight,
excitement, dreaming like fantasy for Disco, Pubs, Balls and other entertainment
places.
1.Open the box:
When you receive the product, take it gently check if there are problem which cause
in transportation. Please report the transportation company about the damage if any,
and keep the damaged case as the evidence.
2. Operating:
(1) Front chart:

3
Manual TR 101 Triton Blue
WWW.TRITON-BLUE.COM
(2) Back chart:
3. Operation
1) MUSIC CONTROL (Sound Activated)
DON’T connect the DMX cable and Set the ADDRESS (DIP Switch) on the back of
the equipment as shown in Graph (a) below (Set the tenth switch as ON). Power
on SUPER-1, now it is under the control of MUSIC. MENTION: After SUPER-1 was
powered, the laser would be shot out from the aperture of the front panel in 10
SECONDS.
Graph (a)
2) SYNCHRONOUS MUSIC CONTOL (Cables Connected):
Connect several pcs of SUPER-1 with DMX-512 cables one by one as shown in Graph
(b), and set the ADDRESS (DIP Switch) on the back of each equipment as shown in
Graph (a) above (Set the tenth switch as ON). Power on all SUPER-1, now they are
on the operating model of SYNCHRONOUS MUSIC CONTOL.
Graph (b)
3) DMX-512 CONTROL (Single Equipment):
Set the DMX address (DIP Switch) on the back of the equipment as shown in Graph
(c) below (Set the first switch as ON), and connect SUPER-1 with a standard DMX-512
controller. Power on the equipment, the description of each channel is listed below:
Graph (c)

4
Manual TR 101 Triton Blue
WWW.TRITON-BLUE.COM
Channel 001 Mode
Channel 002 Patterns
Channel 003 Rotation
Channel 004 X-axes Rolling
Channel 005 Y-axes Rolling
Channel 006 X/Y Direction Moving
Channel 007 Drawing Speed
Channel 008 Scanning Speed
4) Multi-units Connected:
Connect the first SUPER-1 with a DMX-512 controller and then connect it with other
equipments one after another with the DMX-512 cables.
The laser show system is controlled with USITT DMX512 (1990). With the help of
proper ADDRESS (DMX DIP SWITCH) setting, multiple equipments could be controlled
separately with a standard DMX-512 controller.
To set the ADDRESS (DMX DIP SWITCH) properly as you want, some calculation
has to be done. As shown in Graph (d), the value of each corresponding BIT in
ADDRESS is listed. The first controlled channel of each equipment is the amount of
the set-on BIT value. Please read examples below:
Graph (d)
For example,
A) If the ADDRESS is set as shown in Graph (e), only the first BIT is set on. The amount of the
set-on BIT value is 1, so the first controlled channel is channel 001. The description of each
channel of this equipment is:
Channel 001 Mode
Channel 002 Patterns
Channel 003 Rotation
Channel 004 X-axes Rolling
Channel 005 Y-axes Rolling
Channel 006 X/Y Direction Moving
Channel 007 Drawing Speed
Channel 008 Scanning Speed

5
Manual TR 101 Triton Blue
WWW.TRITON-BLUE.COM
B) If the ADDRESS is set as shown in Graph (f), the first and fourth BIT is set on. The amount of
the set-on BIT value is 9, so the first controlled channel is channel 009. The description of each
channel of this equipment is:
Channel 009 Mode
Channel 010 Patterns
Channel 011 Rotation
Channel 012 X-axes Rolling
Channel 013 Y-axes Rolling
Channel014 X/Y Direction Moving
Channel 015 Drawing Speed
Channel 016 Scanning Speed
C) If the ADDRESS is set as shown in Graph (g), the first, third, fifth and eight BIT is set on. The
amount of the set-on BIT value is 9, so the first controlled channel is channel 009. The description
of each channel of this equipment is
Channel 149 Mode
Channel 150 Patterns
Channel 151 Rotation
Channel 152 X-axes Rolling
Channel 153 Y-axes Rolling
Channel 154 X/Y Direction Moving
Channel 155 Drawing Speed
Channel 156 Scanning Speed
And so on……
Following the instruction shown above, many pcs of equipment could be controlled with DMX-512
synchronously.
4. Installation
 Please confirm whether the voltage you have is same as signed on the light before
install.
 Installed by technician. It muse be placed safety and best light angle.
 Must keep space between light equipments and combustibles more than half a
meter. Keep space between light equipments and wall more than 0.15 meter.
 The fans and vent-pipes should not be jammed by other equipment and decorate
materials.
 The light must be fixture installed.
 In safely view please put ground wire into the ground.
 Don’t touch the product and draw the power line if you hand wet.
 Don’t look the light directly to prevent make some destroy with eyes.
 During devise is working unconditional avoid that the cable can to touch the case.

6
Manual TR 101 Triton Blue
WWW.TRITON-BLUE.COM
5. Maintain
 Maintenance should be performed every 15-day period, by using a sponge which
is dipped with alcohol, rather than wet cloth or other chemical liquid, to clean the
mirror,
 Warning: Power must be disconnected before maintenance or repair. Do not look at
the light source directly.
ATTENTION: DISCONNECT INPUT POWER BEFORE MAINTAIN.
DON’T LOOK STRAIGHTLY AT THE LIGHT SOURCES.
NOTE: Don’t separate laser machine from laser power and repair them by yourself
otherwise no good repair service will be supplied.
6. Specification
� Voltage: AC220/110V, 50/60Hz
� Total power: 100W
� Control: High capacity and speed microprocessor
� Input signal bandwidth: 0~1000Hz
� Control Port:DMX-512(8control channels) Sound-activated
� Condition temperature: 0℃~40℃
� Size: 300X270X160mm
� Net Weight: 5.0 kg