Triumph 45-6099BLU User manual

1
For Customer Service Call 1-888-996-2729
© 2017 Escalade Sports
1-888-996-2729
FAX: [phone]
[e-mail]
We strive to ensure that our products are of the highest quality
and free of manufacturing defects or missing parts. However, if
you have any problems with your new product,
DO NOT RETURN IT TO THE STORE,
please contact us toll free @:
Or write to:
Escalade Sports
Customer Service Department
P.O. Box 889
Evansville IN 47706
When contacting Escalade Sports please provide your model number, date code (if
applicable), and part number if requesting a replacement part. These numbers are
located on the product, packaging, and in this owners manual.
Your Model Number:
Please have your model number when inquiring about parts.
Date Code:
All Rights Reserved
Purchase Date:
PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
45-6099BLU
2-45-6099BLU- -JL

IMPORTANT! READ EACH STEP
IN THIS MANUAL BEFORE YOU
BEGIN THE ASSEMBLY.
TWO (2) ADULTS ARE REQUIRED TO ASSEMBLE
THIS BIG SHOT II BASKETBALL
READ AND FOLLOW ALL ASSEMBLY, OPERATION, AND
SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO
ADULTS ARE NEEDED TO PUT THIS BASKETBALL
SHOOTOUT TOGETHER.
2 For Customer Service Call 1-888-996-2729
© 2017 Escalade Sports
All Rights Reserved
Tools Needed:
Make sure you understand the following tips before you begin to assemble your
basketball shootout.
1.This game (with Mechanical Scoring Arm) can be played outdoors in dry weather
- but must be stored indoors.
2.Tighten hardware as instructed.
3.Do not over tighten hardware,as you could crush the tubing.
4.Some drawings or images in this manual may not look exactly like your product.
5.To prevent damage to the electronics or to your wall, do not place this unit any closer
than six inches from the wall.
!
WARNING:
1) Do not mix old and new batteries.
2) Do not mix alkaline, standard (carbon zinc), or rechargeable (ni-cad, ni-mh, etc.) batteries.
3) Do not dispose of batteries in fire, batteries may explode or leak.
Allen Wrench (provided)
Phillips Screwdriver
Plyers

Parts List
Board L Tube Top
2pcs
Board Tube
2pcs
Left Tube
1pc
Right Tube
1pc
Horizontal
Frame Brace
U Tube
1pc
Left Mounting
Tube
1pc
Support Tube
2pcs
Right Mounting
Tube
1pc
Ramp Tube
2pcs
Ramp L Tube
2pcs
Ramp U Tube
1pc
Horizontal Tube
2pcs
Ramp Chute
1pc
Electronic Scorer
1pc
Mechanical
Scoring Arm
2pcs
Allen Wrench
1pc
Rim
2pcs
Rim Support
Plate
2pcs
Inflation Pump
With Needle
1pc
Net
2pcs
Backboard
1pc
M6 x 1mm Thick
Washer
18pcs
M6 x 20mm Bolt
16pcs
M6 x 50mm Bolt
6pcs
M6 x 60mm Bolt
4pcs
M6 x 70mm Bolt
4pcs
M6 Lock Nut
32pcs
Basketball
4pcs
3.5 x 10mm Screw
4pcs
Electronic Scorer
Face Plate
1pc
Wrench
1pc
M6 x 92mm Bolt
2pcs
Locking Pin
2pcs
Mechanical Arm
Support Plate
2pcs
Control Box
1pc
Scorer
Control Wire
1pc
38
1pc
A/C Adaptor
1pc
2pcs
39
M6 x 2mm Thick
Plastic Washer
(Packed inside
Scorer Box)
Wing Bolt
(For control box)
3For Customer Service Call 1-888-996-2729
© 2017 Escalade Sports
All Rights Reserved

Plastic Pole
insert-A
2 pcs
8 pcs
PRE-INSTALLED PARTS
P1 P2
Assembly Instructions
Find a clean, level place to begin the assembly of your Basketball Game. We recommend that two adults work
together to assembly this basketball game.
Remove all the parts from the box and verify that you have all of the listed parts as shown on the Parts List.
Carefully cut or tear the four corners of the box so that the bottom of the box can be used as your work surface.
STEP 1
Plastic Pole
insert-B Spring Lock
8 pcs
P3
PARTS REQUIRED:
2 pcs - #2 Board Tube
1 pc - #3 Left Tube
1 pc - #4 Right TUbe
Attach the Board Tubes (#2) to the Left Tube (#3) and
Right Tube (#4) using Spring Lock as shown in
FIGURE 1.
2
3 4
FIGURE 1
4For Customer Service Call 1-888-996-2729
© 2017 Escalade Sports
All Rights Reserved
Please study each diagram closely and read all assembly notes to insure correct assembly

STEP 2
PARTS REQUIRED:
1 pc - #6 Left Mounting Tube
2 pcs - #7 Support Tube
1 pc - #8 Right Mounting Tube
Attach the Support Tubes (#7)
to the Left Mounting Tube (#6)
and Right Mounting Tube (#8)
using Spring Lock as shown
in FIGURE 2.
7
6 8
FIGURE 2 NOTE:
Triangle Plate
face inside
STEP 3
PARTS REQUIRED:
2 pcs - #24 M6 x 50mm Allen Head Bolt
2 pcs - #27 M6 Lock Nut
Attach tube from assembly STEP 2 to tube
assembly STEP 1 using Bolts (#24),
and WashersLock Nuts (#27) (#22)
as shown in FIGURE 3.
Do not tighten Bolts
on this step.
6 8
7
43
2
2
NOTE:
Triangle Plate
face inside
NOTE:
Triangle Plate
Assemble
Outside
Spring lock
Forward Spring lock
Forward
Middle hole
Middle hole
face inside
7
24
27 2
7
2
24 27
22
22
7
FIGURE 3
5For Customer Service Call 1-888-996-2729
© 2017 Escalade Sports
All Rights Reserved
2 pcs - #22 M6 x 1 mm Thick Washer
Assemble
Outside
Please study each diagram closely and read all assembly notes to insure correct assembly

STEP 4
PARTS REQUIRED:
1 pc - #5 Horizontal Frame Brace U-Tube 4 pcs - #26 M6 x 70 mm Allen Head Bolt
1 pc - #12 Horizontal Tube 6 pcs - #27 M6 Lock Nut
2 pcs - #24 M6 x 50 mm Allen Head Bolt 1 pc - #31 Wrench
1 pc - #36 Allen Wrench
Attach Horizontal Frame Brace U-Tube (#5) to tubes from assembly STEP 3 using Bolts (#26), Lock
Nuts (#27) and Washers (#22) as shown in FIGURE 4.
Attach Horizontal Tube (#12) to tubes (#2) using Bolts (#24) , Lock Nuts and Washers (#22)(#27)
as shown in FIGURE 4.
Use Wrench (#31) and Allen Wrench (#36) to tighten all Bolts.
Tighten, but do not overtighten.
2
2
7
7
8
6
Note: Do not use
this hole this step.
3
4
5
#5 U-tube assemble Inside
12
24
27
24
27
26
27
27
26
27
27
26
26
FIGURE 4
24
27
22
12
2
7
6For Customer Service Call 1-888-996-2729
© 2017`Escalade Sports
All Rights Reserved
6 pcs - #22 M6 x 1 mm Thick Washer
22
22
22
22
22
22
Please study each diagram closely and read all assembly notes to insure correct assembly

Do not use this hole
Spring lock on top
Use this hole
STEP 5
PARTS REQUIRED:
2 pcs - #1 Board L-Tube Top 2 pcs - #32 M6 x 92 mm Allen Head Bolt
2 pcs - #9 Ramp Tube 2 pcs - #33 Locking Pin
2 pcs - #10 Ramp L-Tube 2 pcs - #39 M6 x 2 mm Thick Plastic Washer
2 pcs - #22 M6 x 1 mm Thick Washer 1 pc - #31 Wrench
2 pcs - #27 M6 Lock Nut 1 pc - #36 Allen Wrench
Insert Board L-Tubes (#1) into Board Tubes (#2) as shown in FIGURE 5.
Attach Ramp Tubes (#9) to Left Mounting Tube (#6) and Right Mounting Tube (#8) using Bolts (#32),
Washers (#22), Washers (#39), Locking Pins (#33) and Lock Nuts (#27) as shown in FIGURE 5.
Use Wrench (#31) and Allen Wrench (#36) to tighten Bolts.
Note: This is a pivot point. “Snug” tighten
Lock Nuts (#27) only. Make sure this assembly
pivots freely.
Attach Ramp L-Tubes (#10) to Ramp Tubes (#9) using
Spring Locks as shown in FIGURE 5.
FIGURE 5
10
10
9
9
8
6
2
2
1
1
39
7For Customer Service Call 1-888-996-2729
© 2017 Escalade Sports
All Rights Reserved
Plastic washer
Please study each diagram closely and read all assembly notes to insure correct assembly

STEP 6
PARTS REQUIRED:
2 pcs - #15 Mechanical Scoring Arm 16 pcs - #23 M6 x 20 mm Bolt
2 pcs - #17 Rim 16 pcs - #27 M6 Lock Nut
2 pcs - #18 Rim Support Plate 1 pc - #31 Wrench
1 pc - #21 Backboard 1 pc - #36 Allen Wrench
2 pcs - #35 Mechanical Arm Support Plate
Attach Rims (#17) and Rim Support
Plates (#18) to the Backboard (#21)
using Bolts (#23) and Lock Nuts (#27)
as shown in FIGURE 6.
Attach Mechanical Scoring Arms (#15)
and Mechanical Scoring Arm Support
Plates (#35) to the Backboard (#21)
using Bolts (#23) and Lock Nuts (#27)
as shown in FIGURE 6.
Use Wrench (#31) and Allen
Wrench (#36) tighten all Bolts.
15
17
18
35
21
23
27
FIGURE 6
NOTE:
Mechanical Scoring
Snug tighten only – overtightening could
strip the screw or break the #30 face plate
Arm (#15)
sensor plug must pass through
Backboard (#21) and Mechanical
Scoring Arm Support Plate (#35)
PARTS REQUIRED:
1 pc - #14 Electronic Scorer
2 pcs - #20 Rim Net
4 pcs - #29 3.5 x 10 mm Screw
1 pc - #30 Electronic Scorer Face Plate
STEP 7
Attach Electronic Scorer Face Plate to the
Backboard (#21) and connect with Electronic
Scorer (#14) using Screws(#29)
as shown in FIGURE 7.
Loop the Rim Net (#20) through the ram horns
on the Rims (#17) as shown in FIGURE 7. FIGURE 7
14
29
20
30
21
8For Customer Service Call 1-888-996-2729
© 2017 Escalade Sports
All Rights Reserved
Note: This is a special rim net
designed to avoid entanglement
with the mechanical scoring arm.`
Net does have a
top and bottom,
The long loops go
to the top.
Please study each diagram closely and read all assembly notes to insure correct assembly

STEP 8
PARTS REQUIRED:
1 pc - #11 Ramp U-Tube
1 pc - #13 Ramp Chute
Slide elastic straps and the sleeve of the Ramp Chute (#13) onto the Board L-Tube Top (#1) as shown
in FIGURE 8 and DETAIL A.
Slide the Ramp U-Tube (#11) into the front sleeve of the Ramp Chute (#13) as shown in FIGURE 8
and DETAIL B.
Attach the Front U-Tube (#11) to the Ramp L-Tube (#10) using Spring Lock as shown in FIGURE 8
and DETAIL C.
Elastic
Strap
Ramp Chute
Upper Sleeve
13
1
DETAIL A
FIGURE 8
13
DETAIL B
11
13
Ramp Chute
Front Sleeve
11
10
DETAIL C
9For Customer Service Call 1-888-996-2729
© 2017 Escalade Sports
All Rights Reserved
Please study each diagram closely and read all assembly notes to insure correct assembly

STEP 9
PARTS REQUIRED:
1 pc - #12 Horizontal Tube
8 pcs - #22 M6 x 1 mm Thick Washer
2 pcs - #24 M6 x 50 mm Bolt
4 pcs - #25 M6 x 60 mm Bolt
6 pcs - #27 M6 Lock Nut
1 pc - #31 Wrench
1 pc - #36 Allen Wrench
Place Horizontal Tube (#12) over the lower / front sleeve of Ramp Chute (#13) and then attach it to the
Ramp U-Tube (#11) using Bolts (#24) and Lock Nuts (#27) as shown in FIGURE 9 and DETAIL D.
Use Wrench (#31) and Allen Wrench (#36) to tighten Bolts. Tighten, but do not overtighten.
With the help of another adult, Attach the Backboard (#21) assembly to the Board L-Tubes Top (#1) using
Bolts (#25), Washers (#22)
, Washers (#22)
and Lock Nuts (#27) as shown in FIGURE 9 and DETAIL E.
At the bottom hole of the backboard, bring the ramp up behind the Tube (#12), attach the ramp tabs of
Ramp Chute (#13) using Bolts (#25) and Lock Nuts (#27) as shown in FIGURE 9 and DETAIL F.
Use Wrench (#31) and Allen Wrench (#36) to tighten Bolts. Tighten, but do not overtighten.
1
FIGURE 9
DETAIL E
DETAIL D
DETAIL F
13
21
25 22
27
27
25
21 1
13
12
24
27
22
13
12
11
10 For Customer Service Call 1-888-996-2729
© 2017 Escalade Sports
All Rights Reserved
Inside
Backboard
assemble this side
Ramp Chute
assemble back side
22
Please study each diagram closely and read all assembly notes to insure correct assembly

Control Wire
PARTS REQUIRED:
1 pc - #16 Control Box 1 pc - #37 Control Wire
1 pc - #34 A/C Adapter 1 pc - #38 Wing Bolt
STEP 10
Connect the Sensor Wire of Mechanical Scoring Arms (#15) to Electronic Scorer (#14) as shown in FIGURE 10.
Connect the Control Wire (#37) to Electronic Scorer (#14) as shown in FIGURE 10 and DETAIL G.
This game has a Dual Power feature. You can insert 3 AA Batteries (not included) into the battery
compartment on the back of the Electronic Scorer (#14) --- OR --- use the A/C Adapter (provided) when
your shootout is close to a power source. Please remove the batteries when you are using the A/C Adapter.
34
14
37
15
STEP 11
Now attach the Control Box (#16) to the right corner of the Ramp U-Tube (#11) using Wing Bolt (#38)
as shown in FIGURE 11.
Run the rest of the Control Wire (#37) through the loops on the Ramp Chute (#13)
Do not over tighten
Wing Bolt #38
.
FIGURE 10
DETAIL G
Control
Wire
Mechanical
Scoring Arm
Sensor
Mechanical
Scoring
ON/OFF SWITCH
Arm
Sensor
Control Box
11
37
16
FIGURE 11
11 For Customer Service Call 1-888-996-2729
© 2017 Escalade Sports
All Rights Reserved
See” FIRST TIME BATTERY INSTALLATION AND NOTICE “ , before installing batteries, located on page 17.
38
Please study each diagram closely and read all assembly notes to insure correct assembly
Install #37 Control
Wire into Hook
and Loop Straps.
NOTE: Smaller
Connector
NOTE: Larger
Connector.

ELECTRONIC SCORER OPERATION
Unscrew screw using a screwdriver and open the battery box. Insert 3 AA batteries ( not included) in the order of
polarity as shown on the inside cover. Then close the cover using a screwdriver. Turn the power ON using the
ON/OFF switch. (if the game will not be used for a long period of the time, we recommend that the batteries
should be removed).
To fold the basketball game into the storage position, remove the Lock Pins (#33) from the
playing position on the Mounting Tubes (#6) &(#8). Lift the Front Horizontal Ramp Support
Tube (#11) until the game is in the storage position as shown in FIG. 12
Control Wire
Visitor
On/Off switch
Insert the Lock Pins (#33)
back into the Mounting
Tubes (#6) & (#8), locking
the basketball game into
the storage position.
33
FIGURE 12
12 For Customer Service Call 1-888-996-2729
© 2017 Escalade Sports
All Rights Reserved
This device complies with the part 15 of the FCC rules. Operation is subject to the following two
conditions :
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired
operation.
Please study each diagram closely and read all assembly notes to insure correct assembly

13 For Customer Service Call 1-888-996-2729
© 2017 Escalade Sports
All Rights Reserved
General Control Box Operation
Trouble Shooting:
Game won't turn on
1.Make sure switch on scorer is in the on position (located on back of backboard).
2.Make sure switch mechanical scoring arm wires are in the home and visitor slots on the scorer.
3.Make sure the control box wire is in the control slot on the scorer.
4.Press/hold down the on/off bottom on the scorer for 2 seconds to turn game on.
Game shuts off during play
1.Check the batteries. Make sure they are new batteries.
2.The batteries might be loose causing the game to shut off.Take off the battery cover on the scorer. Take
a piece of paper, fold it so it fits over the batteries. Put the battery cover back on. This should better
secure the batteries and prevent them from moving in any way.
To be used any time the game has been off and is turned back on.
Please make sure switch is in the “ON” position located at the bottom of the electronic
scorer on the back of the backboard.
Also, make sure batteries are good, located inside of the Electronic Scorer.
1. Press the ON/OFF button for 2 seconds to turn on.
2. Scoreboard will show “01” on the HOME side -- This is pre-set game #1 called “Beat The Time Clock”.
3. Press the “Select Up” or “Select Down” buttons to select games 1 thru 8.
4. Next -- Flow directly into the directions for games 1 thru 8 (Game Options) and follow those directions
step by step for correct electronic scoring and gaming operation.
Additional Electronic Scoring and Gaming Information:
A. Press “Sound” to switch sound ON/OFF during a game while the clock is running.
B. Press “Pause” to pause and then pause again to continue during a game while clock is running.
C. Press and hold the “ON/OFF” button for 3 seconds to turn off the Electronic Scorer.
D. Press and hold the “RESET” button for 3 seconds to return to Game Options.
E. NOTE: If no shot is made or no button is pressed in 15 minutes, scorer will turn off automatically.
CONTROL BOX DIAGRAM

14 For Customer Service Call 1-888-996-2729
© 2017 Escalade Sports
All Rights Reserved
Game Options
1. Beat the time Clock
Press "PLAY" to enter game 1.
Press "UP or Down" to select single/multiple players (P1/P2/P3/P4).
Press "PLAY" after the number of player is selected.
Press "UP/Down" to select playing time, 30/45/60 seconds.
Press "PLAY" to begin the game.
Scoreboard "HOME" shows Player 1, 3; Scoreboard "VISITOR" shows Player 2, 4.
All shots worth 2 points until last 10 seconds, each score counts 3 points.
Countdown 5 seconds to next player's turn when one player finishes game.
Player with more points scored wins ( LED will flash on player with higher score).
P
To go to another game, turn game off and back on, follow steps 1 thru 4 in General Control Box Operation.
To go to another game, turn game off and back on, follow steps 1 thru 4 in General Control Box Operation.
To go to another game, turn game off and back on, follow steps 1 thru 4 in General Control Box Operation.
To go to another game, turn game off and back on, follow steps 1 thru 4 in General Control Box Operation.
ress "PLAY" to restart this game.
2. 3 Point Beat the Time Clock
Press "PLAY" to enter game 2.
Press "UP or Down" to select single/multiple players (P1/P2/P3/P4).
Press "PLAY" after the number of player is selected.
after the number of player is selected.
Press "UP/Down" to select playing time, 30/45/60 seconds.
Press "PLAY" to begin the game.
Scoreboard "HOME" shows Player 1, 3; Scoreboard "VISITOR" shows Player 2, 4.
All shots made count 3 points.
Countdown 5 seconds to next player's turn when one player finishes game.
Player with more points scored wins ( LED will flash on player with higher score).
Press "PLAY" to restart this game.
3. Battle Back
Press "PLAY" to enter game 3.
Press "UP or Down" to select 2 players / 4 players.
Press "PLAY"
Shot made in "HOME" frame, +2 points scored display on "HOME" board and -2 points for "VISITOR".
Shot made in "VISITOR" frame, +2 points scored display on "VISITOR" board and -2 points for "HOME".
Once a player scores 10 points who wins and game is finished.
Press "PLAY" to restart this game.
4. Horse
Press "PLAY" to enter game 4.
Press "UP or Down" to select multiple players (P2/P3/P4).
Press "PLAY" after the number of player is selected.
Player has to make a shot in 2 seconds.
First player is allowed to shoot at any hoop (Home or VISITOR). If first player scores in 2 seconds, no letter is
given. Game continues for next player. Scoreboard will display "next player(P2P3/P4)" and LED will flash twice
in a second. After flash, next player has to duplicate the shot in the same hoop selected by first player.
If player can't score in 2 seconds, player receives the first letter "H" which will display on scoreboard. Game
remains for the same player until the player scores. If player keeps missing, player receives "O" followed by "R",
"S", "E". The letter "E" is given, the player is out.
The first player to spell "horse" loses. Players stay in repeat step d.e.f. till game is finished.
The last player to spell "horse" wins. Press "PLAY" to restart this game.

15 For Customer Service Call 1-888-996-2729
© 2017 Escalade Sports
All Rights Reserved
5. Check Point
Press "PLAY" to enter game 5.
Press "UP or Down" to select single/multiple players (P1/P2/P3/P4).
Press "PLAY" to begin the game.
"HOME" displays "player", "VISITOR" displays "24" points, pre-set 40 seconds playing time.
Points scored will display on scoreboard "HOME"
Before time is out, once 24/52/68/86 points is scored, playing time increases 10/20/10/20 seconds respectively.
Countdown 5 seconds to next player's turn when one player finishes game.
Player with more points scored wins ( LED will flash on player with higher score).
Game is finished when a player scores 99 points. Press "PLAY" to restart this game
6. Around the World
Use tape to mark the shooting lines. Press "PLAY" to enter game 6.
Press "UP or Down" to select single/multiple players (P1/P2/P3/P4).
Press "PLAY" after the number of player is selected.
Scoreboard "HOME" displays Player 1/2/3/4, "VISITOR" displays scored points.
Once score comes to 10 points or time comes to 99 seconds countdown 5 seconds to next player's turn when one
player finishes game.
Player who finishes the game first wins (LED will flash on winner). Press "PLAY" to restart this game.
7. Left and Right Shoot
Press "PLAY" to enter game 7.
Press "UP or Down" to select single/multiple players (P1/P2/P3/P4).
Press "UP or Down" to select single/multiple players (P1/P2/P3/P4).
Press "PLAY" after the number of player is selected.
Press "PLAY" after the number of player is selected.
Press "UP or Down" to select playing time, 30/45/60 seconds.
Press "PLAY" to begin the game.
Press "UP or Down" to select playing time, 30/45/60 seconds.
Press "PLAY" to begin the game.
Scoreboard "HOME" displays Player, "VISITOR" displays points.
Make a shot in "HOME" frame when LED is flashing on "HOME", 2 points scored display on "HOME".
Make a shot in "VISITOR" frame when LED is flashing on "VISITOR", 2 points scored display on " VISITOR".
Countdown 5 seconds to next player's turn when one player finishes game.
Player with more points scored wins ( LED will flash on player with higher score). Press "PLAY" to restart this
game.
8. One on One
Press "PLAY" to enter game 8.
Shot made in "HOME" frame, 2 points scored for "HOME", all shots count 3 points in last 10 seconds.
Shot made in "VISITOR" frame, 2 points scored for "VISITOR", all shots count 3 points in last 10 seconds.
Player with more points scored wins when time is out.
Press "PLAY" to restart this game.
To go to another game, turn game off and back on, follow steps 1 thru 4 in General Control Box Operation.
To go to another game, turn game off and back on, follow steps 1 thru 4 in General Control Box Operation.
To go to another game, turn game off and back on, follow steps 1 thru 4 in General Control Box Operation.
To go to another game, turn game off and back on, follow steps 1 thru 4 in General Control Box Operation.

Spare Parts List
1 45-6099BLUJL1 Board L Tube Top
2 45-6099BLUJL2 Board Tube
3 45-6099BLUJL3 Left Tube
4 45-6099BLUJL4 Right Tube
5 45-6099BLUJL5 Horizontal Frame Brace U Tube
6 45-6099BLUJL6 Left Mounting Tube
7 45-6099BLUJL7 Support Tube
8 45-6099BLUJL8 Right Mounting Tube
9 45-6099BLUJL9 Ramp Tube
10 45-6099BLUJL10 Ramp L Tube
11 45-6099BLUJL11 Ramp U Tube
12 45-6099BLUJL12 Horizontal Tube
13 45-6099BLUJL13 Ramp Chute
14 45-6099BLUJL14 Electronic Scorer
15 45-6099BLUJL15 Mechanical Scoring Arm
16 45-6099BLUJL16 Control Box
17 45-6099BLUJL17 Rim
18 45-6099BLUJL18 Rim Support Plate
19 45-6099BLUJL19 Inflation Pump With Needle
20 45-6099BLUJL20 Net
21 45-6099BLUJL21 Backboard
22 45-6099BLUJL22 M6 X 1mm Thick Washer
23 45-6099BLUJL23 M6 X 20mm Bolt
24 45-6099BLUJL24 M6 X 50mm Bolt
25 45-6099BLUJL25 M6 X 60mm Bolt
26 45-6099BLUJL26 M6 X 70mm Bolt
27 45-6099BLUJL27 M6 Lock Nut
28 45-6099BLUJL28 Basketball
29 45-6099BLUJL29 3.5 x 10mm Screw
30 45-6099BLUJL30 Elestronic Scorer Face Plate
31 45-6099BLUJL31 Wrench
32 45-6099BLUJL32 M6 X 92mm Bolt
33 45-6099BLUJL33 Locking Pin
34 45-6099BLUJL34 A/C Adapter
35 45-6099BLUJL35 Mechanical Arm Support Plate
36 45-6099BLUJL36 Allen Wrench
37 45-6099BLUJL37 Scorer Control Wire
38 45-6099BLUJL38 Wing Bolt
39 45-6099BLUJL39 M6 x 2mm Thick Plastic Washer
40 45-6099BLUJLP1 Plastic Pole Insert-A
41 45-6099BLUJLP2 Plastic Pole Insert-B
42 45-6099BLUJLP3 Spring Lock
2
2
1
4
1
4
1
32
1
4
2
4
1
1
2
1
2
2
1
2
2
1
1
2
1
1
2
1
1
1
2
2
2
2
1
8
2
8
43 45-6099BLUJLK1 Hardware Kit
44 45-6099BLUJLM1 Instruction Manual
1
1
1
18
16
6
16 For Customer Service Call 1-888-996-2729
© 2017 Escalade Sports
All Rights Reserved

17 For Customer Service Call 1-888-996-2729
© 2017 Escalade Sports
All Rights Reserved
First Time Battery Installation:
Locate battery compartment for this product .
Use alkaline batteries for maximum performance .
Using a small Phillips head screwdriver – loosen and remove the battery compartment cover
screw(s).
Remove battery compartment cover .
Install new batteries only after reading the “ Battery Information NOTICE“ !
Replace compartment cover and secure cover with the cover screw . Do not over tighten and
strip out the screw .
Notice:
1. Remove and replace batteries when the electrical features of this product work slowly or are not
functional .
2. Do not mix old and new batteries .
3. Do not mix different types of batteries : Alkaline , Standard ( Carbon-Zinc) , or rechargeable
( Nickel-Cadmium batteries ) .
4. Use Alkaline Batteries for maximum performance .
5. Do not use damaged batteries .
6. Use only batteries of the same or equivalent type as recommended.
7. Install new batteries as per matching the battery polarity guide ( + & - , positive and negative ) inside
of the battery compartment . Correct battery polarity installation is critical as to not damage the internal
electrical components as well as insuring the correct functionality of the product .
8. Do not short circuit the battery terminals .
9. Always remove exhausted , leaking, weak , and batteries from long periods of nonuse from the
product . Battery leakage and corrosion can cause damage .
10. Check the battery terminals are clean and bright before installing new batteries.
11. Dispose of old batteries safely and per local battery disposal codes .
12. Do not dispose of batteries into a fire as they may explode or leak.
13. If removable rechargeable batteries are used , they are to be charged under adult supervision .
14. Rechargeable batteries are to removed from the product before they are charged .
15. If you use a battery charger, it should be examined regularly for damage to the cord , plug, enclosure,
and other parts. Do not use a damaged or malfunctioning charger until it is properly repaired.
16. Non rechargeable batteries must not be recharged .
17. Always remove batteries from this product for extended storage and or non-use .
18. Should this product cause , or be affected by, local electrical interference , move it away from other
electrical equipment . Reset ( switching off and back on again and or removing and reinserting the
batteries ) if necessary .
IMPORTANT: BATTERY INFORMATION
Please retain this information for future reference. Batteries must be installed / replaced by an adult .

18
For Customer Service Call 1-888-996-2729
© 2017 Escalade Sports
All Rights Reserved.
This consumer warranty extends to the original consumer purchase of any ESCALADESPORTS
Product (hereinafter referred as the "Product").
WARRANTY DURATION: This Product is warranted to the original consumer purchase of a pe-
riod of 90 days from the original purchase.
WARRANTY COVERAGE: ESCALADE SPORTS warrants to the original Consumer Purchaser
that any Product of its manufacture is free from defects in material and workmanship when used
for the intended purpose under normal use and conditions. THIS WARRANTY IS VOID IF THE
PRODUCT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE,
IMPROPER SERVICE, FAILURE TO FOLLOW INSTRUCTIONS PROVIDED WITH THE PROD-
UCT OR OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL AND WORKMAN-
SHIP.
WARRANTY PERFORMANCE: During the above 90 day warranty period, ESCALADESPORTS
shall repair or replace with a comparable model, and Product, or component thereof, which may
prove defective under normal use and proper care, and which our examination shall disclose to
our satisfaction to be thus defective, please contact our Warranty Dept.
1-888-996-2729 / Warranty Dept.
Or Write us at:
Escalade® Sports, Inc. - P.O. Box 889, Evansville, IN 47706
Attn: Warranty Dept.
Or E-mail us at:
[email protected]
Other than shipping requirements no charge will be made for such repair or replacement of in-
warranty Products. ESCALADE SPORTS strongly recommends that the Product is insured for
value prior to mailing.
WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF
THIS SALE, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIM-
ITED IN DURATION TO THE ABOVE 90 DAY PERIOD. ESCALADE SPORTS
SHALL NOT BE LIABLE FOR LOSS OF USE OF THE PRODUCT OR OTHER
CONSEQUENTIAL OR INCIDENTAL COSTS, EXPENSES OR DAMAGES IN-
CURRED BY THE CONSUMER OF ANY OTHER USE.
Some states do not allow the exclusion or limitation of implied warranties or consequential or
incidental damages, so the above limitations or exclusions may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights and you may also have other
rights which may vary from state to state.
90 DAY LIMITED WARRANTY