TRIVIEW TFD-2210 Technical manual

PRODUCT FEATURES
• 1/3” Sony HAD II CCD
• 540TVL
• 2.8-10mm / F1.2 Varifocal Auto Iris Lens
• Mechanical IR Push Filter (ICR)
SAFETY PRECAUTIONS
• The installation should be made by a qualified service person and should be complied with
all local codes.
• Only use class 2 regulated power supply as 12VDC power source.
• To prevent fire or electrical shock, UL listed class 2 wiring should be used for the power
supply.
• Make sure the ceiling / wall is strong enough to support the weight of the camera.
• Do not attempt to disassemble the camera. There are no user-serviceable parts inside. The
warranty will be voided if the seal is broken.
• Do not attempt to aim the camera directly at the sun or other extremely bright objects.
This can damage the image sensor.
• Do not place the camera under the following locations.
1. Extremely high or low temperatures
(Operating temperature: -10°C to +50°C [10°F to 122°F])
2. High levels of humidity and dust
(Operating humidity: max 80% no condensation)
3. Locations where there are large amounts of water vapor and steam.
• Avoid strong impacts or shocks. The camera could be damaged by improper handling or
storage.
• Be sure to use the proper screws to mount the camera on the wall or ceiling.
Version: 20100406
Model:
TFD-2210
Vandal Resist IR Dome Camera
OPERATION INSTRUCTION
CONTENT LIST
• TFD-2201 1 pc
• Operating Instruction 1 pc
• Torx Wrench 1 pc
• Pigtail cable 1 pc
• Tapping Screws 3 pcs
• Plastic Anchors 3 pcs
PART DISCRIPTION
• 12VDC/24VAC Dual Voltage
• Dynamic Noise Reduction
• 3-axis design
DC LEVEL L.L V.P
AES
AGC
BLC
F.L
OFF
NOM
OFF
OFF
1. Far / Near
2. Wide / Tele
3. DC Level
Adjust the IRIS level of the Auto Iris Lens
4. Dip Switches
AES: Automatic Electronic Shutter
Turn off when Auto Iris lens is used
BLC: Backlight Compensation
Turn on when there is a strong backlight to enhance the foreground
AGC: Automatic Gain Control
Gain adjusted from 0 to 26dB automatically
FL: Flickerless
Change the shutter speed to 1/120sec
5. Secondary DC Power Input
6. Service Port
2nd video output for service monitor
7. Power Input
Support 12VDC or 24VAC
8. Video Output

INSTALLATION
1. Separate the dome cover from the camera base. Use camera base as a tem-
plate to mark the mounting holes.
2. Drill holes on the ceiling /wall and cut a Ø 1” hole for the cable to pass
through.
3. Mount the camera base to the ceiling / wall.
4. Connect the service monitor to the service port. Aim the camera to the desire
angle by adjusting the Pan / Tilt / Zoom / Focus.
5. Attached the dome cover to dome base.
SPECIFICATION
Image Sensor 1/3” Sony Super HAD II CCD
Total Pixel 811 (H) x 508 (V)
Horizontal Resolution 540 TVL
Sensitivity 0 Lux when IR is ON
Lens 2.8-10mm / F1.2
S/N Ratio more than 50 dB
Horizontal Frequency 15.734 KHz
Vertical Frequency 59.94 Hz
Power 12VDC / 24VAC
Power Consumption ~3W (250mA) IR OFF
~8W (670mA) IR ON
Synchronization Internal
IR Illuminator Thirty (30) 850nm LED
IR LED off > 5 lux, IR LED on < 2 lux
Illuminated Distance 100 ft
Mechanical IR Cut Filter Color Mode > 5 lux, B/W Mode < 2 lux
Electronic Shutter ON ( 1/60 sec ~ 1/100,000 sec) / OFF ( 1/60 sec)
Backlight Compensation ON / OFF
Automatic Gain Control ON / OFF
White Balance Automatic
Noise Reduction (DNR) Automatic
Operating Temperature -10ºC to +50ºC
Operating Humidity Maximum 80% RH
Housing Aluminum Alloy
Dimensions (Dia x H) 5.51” x 4.41” (140 x 112 mm)
Weight 2.09lb
Safety Compliance FCC, CE
Note: Design and specifications are subject to change without notice.

OPTIONAL ACCESSORIES
THT-2210
Heater unit for TFD-2201
TWM-2210
Wall Mount Kit for the TFD-221x
TFM-2210
Ceiling Mount Kit for the TFD-221x