Trotec BX09 User manual

TRT-BA-BX09-TC2015-41-003-EN
BX09
EN
OPERATING MANUAL
ENERGY COST MEASURING
DEVICE

2 EN
energy cost measuring device BX09
Table of contents
Notes regarding the operating manual.................................2
Safety .....................................................................................2
Information about the device................................................3
Transport and storage...........................................................4
Operation ...............................................................................5
Maintenance and repair ........................................................5
Errors and faults....................................................................6
Disposal .................................................................................6
Notes regarding the operating manual
Symbols
Warning of electrical voltage
This symbol indicates dangers to the life and health of
persons due to electrical voltage.
Warning
This signal word indicates a hazard with an average
risk level which, if not avoided, can result in serious
injury or death.
Caution
This signal word indicates a hazard with a low risk
level which, if not avoided, can result in minor or
moderate injury.
Note
This signal word indicates important information (e.g.
material damage), but does not indicate hazards.
Info
Information marked with this symbol helps you to carry
out your tasks quickly and safely.
Follow the manual
Information marked with this symbol indicates that the
operating manual must be observed.
You can download the current version of the operating manual
and the EU declaration of conformity via the following link:
BX09
https://hub.trotec.com/?id=42345
Safety
Read this manual carefully before starting or using the
device. Always store the manual in the immediate vicinity
of the device or its site of use!
Warning
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may
result in electric shock, fire and/ or serious injury.
Save all warnings and instructions for future
reference.
This appliance can be used by children aged from
8years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.
• Do not use the device in potentially explosive rooms.
• Do not use the device in aggressive atmosphere.
• Do not immerse the device in water. Do not allow liquids to
penetrate into the device.
• Observe the input values specified in the Technical data
chapter and do not exceed them under any circumstances.
• Protect the device from permanent direct sunlight.
• Do not cover the device! With a higher power input the
device will warm up. Covering the device may cause
overheating and consequently may cause a fire!
• Do not remove any safety signs, stickers or labels from the
device. Keep all safety signs, stickers and labels in legible
condition.
• Do not open the device.
• Do not connect several devices by plugging one into
another.
• Only operate the device in dry surroundings.
• Please note that the device is only de-energized when the
plug has been disconnected from the mains.

EN 3
energy cost measuring device BX09
• Observe the storage and operating conditions as given in
the Technical data chapter.
Intended use
Only use the device for measurements on circuits directly
connected to the low-voltage grid via a plug connection, e. g.
household appliances, portable electrical appliances etc., whilst
adhering to the technical data.
To use the device for its intended use, only use accessories and
spare parts which have been approved by Trotec.
Improper use
The device is not suitable for use with any type of extension
cables. The device may not be used in potentially explosive
atmospheres, when wet or very humid.
Personnel qualifications
People who use this device must:
• have read and understood the operating manual, especially
the Safety chapter.
Residual risks
Warning of electrical voltage
Work on the electrical components must only be
carried out by an authorised specialist company!
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Warning
The device is not a toy and does not belong in the
hands of children.
Warning
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Caution
Keep a sufficient distance from heat sources.
Note
To prevent damages to the device, do not expose it to
extreme temperatures, extreme humidity or moisture.
Note
Do not use abrasive cleaners or solvents to clean the
device.
Information about the device
Device description
The device BX09 measures the energy demand of a connected
terminal device.
The consumption of the device can be displayed in watts, kWh,
the price or costs per kWh.
Device depiction
1
2
3
4
5
6
No. Designation
1 Connection to socket
2 Connection to terminal device (plug adapter)
3UP button
4MODE button
5SET key
6 Display

4 EN
energy cost measuring device BX09
Display
COST /KWHWPRICEKWH
7
891011
No. Designation
7 Measurement value display
8KWH display – consumption indicated in kilowatt hours
9W display – consumption indicated in watts
10 COST/KWH display – consumption indicated as costs per
kilowatt hours
11 PRICE display – consumption indicated as the overall
costs
Technical data
Parameter Value
Model BX09
Power supply 230VAC , 50/60Hz
Load, max. 16 A, 3680 W
Measuring range resolution 0.1W
0.01 kWh
Accuracy ±2% or ±2W (0-100W);
±2% (100-3680W)
Display range 0.00 to 9999.9kWh
0.00 to 9999 overall costs
Storage conditions 5 °C to 40 °C, <85 %RH
Measuring circuit category CATII, 2500V
Type of protection IP20
Dimensions
(lengthx widthx height)
95x 51x 70 mm
Weight (packaging excluded) 100g
Scope of delivery
• 1 x Energy cost measuring device BX09
• 1 x Quick guide
Transport and storage
Note
If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.
Transport
When transporting the device, ensure dry conditions and and
protect the device from external influences e.g. by using a
suitable bag.
Storage
When the device is not being used, observe the following
storage conditions:
• dry and protected from frost and heat
• protected from dust and direct sunlight
• The storage temperature is the same as the range given in
the Technical data chapter.

EN 5
energy cost measuring device BX09
Operation
Switching the device on
1. Plug the device into a properly fused socket.
2. Connect the terminal device to the plug adapter.
ðThe device is switched on.
Setting the price per kilowatt hour
Note:
The default setting ex factory of the price per kilowatt hour is
0.0.
1. Press the MODE button(4) several times until
COST/KWH(10) appears on the display(6).
ðThe currently set price per kilowatt hour is indicated on
the display(6).
2. Press the SET button(5).
ðThe first digit in the measurement value display(7)
flashes.
3. Repeatedly press the UP button(3) to set the desired value.
4. Then press the SET button(5) again.
ðThe second digit in the measurement value display(7)
flashes.
5. Repeatedly press the UP button(3) to set the desired value.
6. Continue until all four digits have been set.
7. Then press the SET button(5) again.
ðThe decimal point in the measurement value display(7)
flashes.
ðIf required, you can change the position of the decimal
point by use of the UP button(3).
8. Press the SET button(5).
ðThe price per kilowatt hour is set and indicated on the
display(6).
Changing the display mode
The device can display the following values:
• the overall costs (PRICE)
• the price per kilowatt hour (COST/KWH)
• the consumption in real time (W)
• the overall consumption since switch-on (KWH)
1. Press the MODE button(4) until the desired display mode
is set.
Reset
Please proceed as follows to reset the display for the measured
kilowatt hours to 0.00:
1. Repeatedly press the MODE button(4) until the device is in
the display mode for overall consumption since switch-on
(KWH).
2. Press and hold the MODE button(4) for approx. 3s.
ðThe overall consumption since switch-on is reset to
0.00.
Internal memory
The device comes with an internal memory. The price per
kilowatt hour and the overall costs are saved, even if the device
is not connected to the mains.
Shutdown
1. Disconnect the terminal device from the plug adapter.
2. Disconnect the device from the mains.
3. Store the device according to the Storage chapter.
Maintenance and repair
Cleaning
Clean the device with a soft, damp and lint-free cloth. Make
sure that no moisture enters the housing. Do not use any
sprays, solvents, alcohol-based cleaning agents or abrasive
cleaners, but only clean water to moisten the cloth.
Repair
Do not modify the device or install any spare parts. For repairs
or device testing, contact the manufacturer.

6 EN
energy cost measuring device BX09
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
For repairs or device testing, contact the manufacturer.
Fault Remedy
The device display indicates
unusual characters or values.
Disconnect the device from the
mains and reconnect it after a
brief period of time. Check
whether the fault is eliminated.
Please contact the Trotec
customer service if the
problem persists.
The device does not respond to
the push of a button.
Disposal
The icon with the crossed-out waste bin on waste
electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. For further return options provided by us please
refer to our website www.trotec24.com.
The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.

Trotec GmbH
Grebbener Str. 7
D-52525 Heinsberg
[phone]
[phone]
[email protected]
www.trotec.com