Trotec Carbide Owner's manual

TRT-BA-CARBIDE-TC2020-33-001-EN
CARBIDE
EN
SUPPLEMENTAL SHEET
HOLE SAW SET

2 EN
hole saw set carbide
Important notes
You can download the current version of the operating manual
via the following link:
https://hub.trotec.com/?id=44658
Also observe the instructions for your tool, particularly the safety
chapter.
Warning
Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Warning
Do not process materials containing asbestos.
Asbestos is considered carcinogenic.
Warning of hot surface
The insertion tool might still be hot after the
application. Burn hazard when touching the insertion
tool.
Do not touch the insertion tool bare-handed!
Wear protective gloves!
Warning
Toxic dusts!
The harmful / toxic dusts produced during operation
pose of risk to the health of the operator and persons
in the vicinity.
Wear eye protection and a dust mask!
Warning
The tool holder must be firmly locked in place before
switching the device on, for an insufficiently or
incorrectly clamped accessory could be catapulted out
of the tool holder uncontrollably upon switch-on.
Personal protective equipment
Wear hearing protection.
Excessive noise can lead to hearing loss.
Wear eye protection.
With it you protect your eyes from splintering, falling
and flying pieces which could cause injuries.
Wear a protective mask.
It saves you from inhaling harmful dusts generated
when processing workpieces.
Wear protective gloves.
They protect your hands from burns, crushing injuries
and skin abrasions.
Product overview
Product description
The Carbidehole saw set is ideal for hole circle cuts with a
cutting depth of up to 25mm. It is particularly suitable for
materials such as stone, tiles, concrete or plaster. The
Carbidehole saw set is compatible with cordless drill drivers
from a power with 16V upwards and with drilling machines
with a 10mm or 13mm drill chuck.
Product depiction
123456
789
No. Designation
1 Saw ring Ø 73mm
2 Saw ring Ø 68 mm
3 Saw ring Ø 44 mm
4 Saw ring Ø 35 mm
5 Saw ring Ø 28 mm
6 Saw ring Ø 22 mm
7 13mm hole saw holder with centre drill forØ 35, 44,
68 ,73mm
8 10mm hole saw holder with centre drill forØ 22,
28mm
9 Allen wrench

EN 3
hole saw set carbide
Operation
Choose the hole saw holder(10mm or 13mm shaft) suitable
for the size of the used drill chuck. Then select a saw ring
according to the desired activity and mount it on the hole saw
holder as follows:
Mounting the saw ring
1. For saw rings(1-4), use the hole saw holder(7). For saw
rings(5,6), use the hole saw holder(8).
2. Unscrew the lock nut(10) from the hole saw holder(7,8).
10
7, 8
3. Slide the desired saw ring(1-6) on the hole saw
holder(7,8).
ðMounting the saw ring(1,2,3 or4) to the hole saw
holder(13mm shaft)
710
1, 2, 3, 4
ðMounting the saw ring(5,6) to the hole saw
holder(10mm shaft)
810
5, 6
4. Screw the lock nut(10) on the hole saw holder(7,8) and
tighten the lock nut.
Removing the centre drill from the hole saw holder
1. Using the supplied hexagonal wrench(9), remove the grub
screw(11) from the hole saw holder(7,8).
12
10
7, 8
11
2. Then remove the centre drill(12) from the hole saw
holder(7,8).
Speed recommendations
Ø in mm
rpm
min. max.
22 200 400
28 180 380
35 160 360
44 120 280
68 100 200
73 80 180
Disposal
Disposal in compliance with official regulations.

Trotec GmbH
Grebbener Str. 7
D-52525 Heinsberg
[phone]
[phone]
[email protected]
www.trotec.com