Tru W-TX User manual

CONNECTING:
For best results use high quality, low impedance, shielded RCA connectors. For stereo inputs
connect to the RCA Audio In jack. This can be connected to line level outputs on a source device
such as a TV or AV receiver. When connecting an LFE or mono source, use the R channel of the
Audio In RCA jack. For some subwoofers, you can use a splitter to connect a LFE/mono sub out to
both the L and R channels of the RCA input to get more volume. Refer to the diagram below for the
system connections.
WIRELESS RANGE:
The range of line of sight for these devices are a 150 feet. Meaning, in an open environment without
obstacles in-between, the transmitter and receiver will work at distances of 150 feet. Worst case
scenario, indoors you may only see around 50 feet of range. In our real world testing we have found
these devices to work solidly at 75 feet. The range of your install will vary based on environment, but
you should be able to see a typical range between 50 ft and 75 feet for most indoor applications.

Pairing with SLIM-PWR44:
1. Connect the W-RX receiver to power, a red light will illuminate.
2. Turn the “Master Power” switch on the back of the SLIM-PWR44 to “ON” (a red light will illuminate on
the front of the soundbar.)
3. On the W-RX receiver press the Pair button, a red light will flash (fig. 1)
4. Press the “Pair” button on the back of the W-RX. A red light will begin to flash.
5. Within 10 seconds of pressing pair on the W-RX, power on the W-TX transmitter by plugging it into a wall
outlet. Note: During the boot up process, the W-TX searches for the W-RX in pair mode and connects
automatically.
6. The LED indicator light will flash while not connected. Once the LED stops flashing and turns solid green,
then the connection is complete.
7. If the first attempt to connect fails, repeat steps 1-5.
8. If connection fails, refer to the trouble shooting steps of this guide.
1. On the W-RX receiver, connect the “Sub Out” to the subwoofer.
2. On the W-TX transmitter, connect an audio source to the Audio In RCA jack. For LFE/mono signals use
the “R” channel of the RCA jack.
3. Apply power to the W-RX receiver (a solid red light will illuminate).
4. Within 10 seconds, press the “on/standby” button on the front of the SLIM-PWR44 (fig. 2). The SLIM-PWR44
searches for the W-RX in pair mode and connects automatically. This may take up to 30 seconds.
5. The LED status indicator on the W-RX will change from blinking red to solid green when connected, and the
light on the SLIM-PWR44 will turn blue.
6. If the first attempt to connect fails, repeat steps 1-5.
7. If connection fails, refer to the trouble shooting steps of this guide.
Fig.1 Fig.2
W-RX
SLIM-PWR44
Pair Button
W-RX Pair Button
Ensure the standby power
to the SLIM-PWR44 is off
before pushing pair on
W-RX (Red Light)

1. Press the “Pair” button on the W-RX, until a red light starts to flash.
2. With the SLIM-PWR44 on and the blue light on, press the “Wireless Sub Pair” button once (located
on the back of the SLIM-PWR44). You have sucessfully paired when the light on the W-RX turn to
green.
In a typical room, the transmitter should be able to transmit to a receiver at a distance up to 50ft. (15m).
Walls, furniture, metal racks, or other objects will interfere with the wireless signal transmission path.
Shorten the distance between the transmitter and receiver to verify full functionality. If the devices can
pair at the shortened distance, then the placement of the receiver is either too far from the transmitter
or there are too many objects obstructing the wireless signal path. You can solve this by finding a
closer placement for the receiver or one that is less obstructed.
SoundVision Technologies dba
SUBWOOFER and ELECTRONIC PRODUCT WARRANTY
All subwoofers and amplifiers have a limited 5 year warranty. This warranty includes lifetime
parts and repair labor on all components. The warranty extends only to the original purchaser of
the product and not to any subsequent owner. TRUAUDIO’s obligation under these warranties
is limited to repairing or replacing any component found defective in material or workmanship
under normal conditions of use with an equal and/or current product. These warranties shall not
apply to products which have been abused, modified, or disassembled. Products to be repaired
or returned under this warranty must be returned to the factory through an authorized TruAudio
dealer with all transportation and insurance charges prepaid.