TSC In wall User manual

USER’S
ManUaL
in waLL
in cEiLing
SpEakERS

In Wall / In Ceiling: PAGE 2
Thank you. And congratulations!
Our thanks for buying your new speakers from TSC. We sincerely appreciate your
condence in us and our products. Please read this Owner’s Manual! It contains
many tips on getting your new speakers set up, connected, and sounding as good as
they should. We hope you nd it clear, concise, and helpful.
Again, thank you.
OUt Of thE BOx
You should save the carton and the inserts your speakers came in. You may need to ship your TSC
speakers in the future and the packaging is designed to protect them from damage.
whERE ShOULd YOU pUt thEM?
With In-Wall/In-Ceiling speakers, placement is a doubly important consideration. Here are three
guidelines to follow:
• Youshouldplaceyournewspeakerswherethey’lldeliverthebestsoundtotheareayou’vechosen.
• Youshouldplacethemwherethey’llhaveminimumimpactonyourdécor.
• Youmustplacethemwheretheywon’timpingeonexistingwiring,plumbing,orHVAC(heating,ventilation,
andairconditioning)ducts.
If you’re concerned that you might not be able to select a good location and install the speakers to your
satisfaction, call a carpenter or someone with drywall experience to help. However, if you’re handy
and aren’t intimidated by drywall or what may be behind it, you’ll need just ordinary coordination and
a few tools to do the job well.
in-waLL SpEakER pLacEMEnt - SOUnd iSSUES
Acoustically, In-wall speakers are similar to bookshelf or oor-standing speakers. They’re subject to
the same conditions rooms impose on all speakers. With that in mind, here are some suggestions.
Main Speakers:
Try to put the main speakers (Left and Right for stereo; Left, Center, and Right for home theater) in the
same wall of your listening/viewing room. If you can place your speakers in the long wall, so much the
better.
Use the “Rule of Thirds”
whenever possible. This
suggests that the best place-
ment for your Left speaker
is approximately 1/3 of the
way along the wall in which
you’re going to mount the
speakers. Similarly, the best
place for the Right speaker
is usually 2/3 of the way
across the same wall.
Make sure that the speaker-to-listening/viewing position distance is the same for each speaker.
Remember that the “Rule of Thirds” is a guideline only. Some professionals recommend placing the
main (Left and Right) speakers so that they form an equilateral triangle with the prime listening/view-
ing position.
Reections from side walls have a major impact on your sound so try not to place your main speakers
close to them. Remember that the “Rule of Thirds” is a guideline only. Try not to place your main
speakers so they’re exactly the same distance from the closest side wall. A bit of asymmetry here is
actually preferable.
When you take the time to place your Main speakers, you’ll enjoy better “imaging” (the apparent place-
ment of individual instruments or voices), and more depth.
Also, remember that the tweeters in your In-wall speakers can be positioned so that they aim directly at
your listening/viewing position.
Center Channel Speakers
For a home theater system, place the center channel speaker between your Left and Right speakers as
close to your TV screen as possible. Try to keep the tweeters of all three speakers (Left, Center, and
Right) as close to the same height as possible. Tweeters at – or very close to – your seated ear level
are ideal. (This may pose a
challenge if you have to place
your Center Channel speaker
either above or below your
TV screen but you shouldn’t
worry too much.)
Try to place the center chan-
nel speaker at exactly the
same distance from your lis-
tening/viewing position as the
main Left and Right speakers.
This helps create the most
convincing image.

In Wall / In Ceiling: PAGE 3
Surround Speakers
Surround speaker placement is challenging. You have two options.
If you’re primarily a music listener, place your in-wall surrounds in the back wall of your listening/
viewing room but a bit closer to the side walls than the “Rule of Thirds” indicates. Make sure the
tweeters are at approximately the same height as are the tweeters of your front Left, Center, and Right
speakers.
If you’re a movie fan, mount the surround speakers in the side walls anking your primary listening/
viewing position. Make sure they’re slightly behind your couch or chair and at least 1.5 to 2’ above ear
level.
Try not to place furniture between your speakers and your listening/viewing position. Make sure you
can see all your speakers when seated there.
You have the option of using In-ceiling speakers for surround channels also. We’ll cover placement
issues for them shortly.
cUtting thE hOLES
Architectural/Construction Issues
Although you can install In-wall speakers in plaster/lathe walls, most of you will encounter drywall
(or “wallboard”) construction in which 5/8” sheets of drywall material are fastened to 2” x 4” vertical
wood studs located at 16” intervals behind the wallboard. (Note that some local construction codes
mandate metal studs. Check with your local government’s building authority.)
The following suggestions assume that you’re installing your speakers in an existing home. If
you’re building a new home, your contractor or architect should make all the provisions you’ll need
for In-Wall or In-Ceiling speakers. Be aware, however, that it’s often difcult to determine proper
speaker placement before you’re actually living in the space.
When you’re selecting nal placement for your In-Wall Speakers, rst determine where the studs are.
Don’t “bet the farm” on always nding them on 16” intervals. Use a stud-nder and mark the location
of all studs near your preferred speaker placement position in light pencil.
1) Makesureyouwon’tbecuttingintoorthroughelectricalwires,
plumbing,orductworkwhenyoucuttheholesforyourspeakers.
First,cutasmalltestholeanduseaashlighttocheckforany
obstructions.
2) Leaveatleast1”ofspacebetweentheedgesoftheholeyouintend
tocutforthespeakersandanystud.Thisleavesroomforthecam
locksthatattachthespeakertothedrywallmaterial.
After you’ve picked out your speaker locations, use the template/
paint shield to mark that location.
1) First,separatetheinstallationtemplatefromtheinnerpaintshield
alongtheperforatedlines.(Youcanthrowoutthedividerthatsepa-
ratespaintshieldfromthetemplate.)
2) Next,placethetemplate(theouterportionofthecombinedtemplate/
paintshield)carefullysothatitoutlinestheexactspotthespeaker
willoccupyafterinstallation.
 • Donot“eyeball”thetemplatelocation.Useameasuringtapeand
leveltocarefullylineupthetemplate.
 • Onceyou’velocatedthetemplateprecisely,youcanuseshort
lengthsoftapetoholditinposition.
3) Usingasoftpencil,carefullydrawalinearoundtheinneredgeofthe
template.Thiswillmarkthecutoutyouwillmakeinthedrywall.
Once the hole is marked:
1) Placeatarpordropclothunderthelocationbeforeyoustartcutting.
2) Useadrywallsawtocarefullycutalongthelinesyou’vejustdrawn.
 • Youcaneither“punchthrough”thedrywallmaterialwiththesaw
ordrillasmallholeatonecornerofthe
  cutouttoplacethebladeaccurately.
3) Whenyou’venished,removethecut-outrectangle.
4) Withlengthsof1”widemaskingtape,sealtheexposededgesofthe
drywallmaterialsothatthetapeoverlapsthefrontandrearsidesof
theholeyou’vejustmade.
Stud Stud
Masking Tape
1”

In Wall / In Ceiling: PAGE 4
cOnnEcting YOUR SpEakERS
Getting Wired
We assume that you’ve already run appropriate wiring from your “head end” (your home theater or
hi- system) to the in-wall or in-ceiling locations you’ve selected. If this is not the case, you may
need help from an electrician or a custom-installation specialist.
Note that most building codes specify suitable wire types for behind-the-wall use. In general, these
specs call for Underwriters Laboratory (UL) CL-2 or CL-3 wiring to minimize the chance of a re
starting behind the walls due to heat. Check with your local government’s building code enforce-
ment division for specics.
Please use 16 gauge wire if your amplier-to-speaker runs are under 50’. For longer runs, we
strongly suggest 14 gauge. (For your reference, standard “lamp cord” available at most hardware
stores is 18 gauge.) For some installations, 4-conductor rather than conventional 2-conductor wire
is much easier, particularly if you’re dealing with stereo pairs of speakers. You can nd CL-2 and
CL-3 wiring in most gauges and conductor counts at good electrical supply houses.
Now that you have good cut-outs for your speakers, you’ll need to connect the speakers to the speaker
wires before nal installation.
Before you begin connecting your speakers, turn your system components OFF. That way, you won’t
run any chance of “shorting” your amplier and possibly damaging it as you’re hooking up your speak-
ers. And, of course, turn your system back ON when you’re done!
TSC In-Wall and In-Ceiling speakers have two spring-loaded terminals for connecting the speaker wire
from your amplier. (Note: The SC-6DT is a one piece stereo speaker with two sets of connection
terminals. Simply duplicate the instructions below for the second set of terminals.)
One of the posts is red (positive or “+”), the other black (negative or “-“). Speaker wire, in turn, has
two conductors, one for the “+” side of the signal, one for the “-“.
Now look at your speaker wire. You’ll see that it has two conductors separated by insulation and iden-
tied by color (if the insulation is clear) or by differences in the insulation itself (ridged vs. plain is the
most common). Choose one conductor to carry the “+” signal and the other for the negative signal. It
makes no difference which one you pick - just maintain that choice for all your connections.
• Preparethewirebyexposingabout3/8”ofeachconductorbystrippingtheinsulationwithawirestripperor
sharpknife.
• Twistalltheindividualstrandsofeachconductortogether.
• Connectthe“+”conductorofthespeakerwiretothe“+”terminalonthespeaker
• Pressdownontheterminal’sredcaptoexposetheholeinthecentershaft.
• Inserttheconductorintotheholeandreleasethecap.
• Connectthe”-“conductorofthespeakerwiretothe“-“terminalonthespeakerinthesamemanner.
Polarity and Proper Phasing
Don’t let these words scare you. They both refer to making sure you get all the sound your speakers are
capable of giving you.
Why are we placing as much emphasis on hookup consistency here? We want you to get all the perfor-
mance you’ve paid for!
When your amplier-to-speaker connections are consistent (when “+” is always connected to “+” and
“-“ is always connected to “-“), your speakers are connected “in phase.” That means the drivers in each
speaker will push out when they get a common positive signal from an amplier and pull in when they
get a negative signal.
When speakers are connected “out of phase,” the drivers ght each other – some move out while others
move in. The result? You’ll get less bass and blurred imaging. That’s a pretty heavy price to pay for
not taking just a few extra seconds to make sure your connections are correct.

In Wall / In Ceiling: PAGE 5
Final Installation
Now that you’ve connected your speakers, it’s time to install them in the cutouts you’ve already made.
To install the speakers:
1) Takeofftheprotectivegrillebygentlypryingupacornerwithasharpknifeblade,awl,orotherpointedtool.
2) Onceyou’vegotonecornerup,begintoworkanothercornerloose.Onceyou’vedonethis,thegrillewill
popoff.
3) Lookatthebackofthespeakerandnotethe“dogleg”camssittingontopofmoldedpostsjustinsidethe
speakers’perimeters.
4) Makesurethesecamsarepointedawayfromthespeaker’souteredge.
5) Gentlyputthespeakerintotheholdyou’vecut.
6) Locatethescrewsonthespeaker’sfrontpanelthatturnthe“dogleg”cams(onescrewforeachcam).
7) WithaPhillips-headscrewdriver,turnascrewcounterclockwise(totheleft),untilyoufeelthecamloosen
fromitspreviouspositionandsettleagainsttherearofthedrywallmaterial.
8) Turnthescrewclockwise(totheright)totightenthecamagainstthedrywall.
9) Repeatthesteps7and8untilallthecamsaretightenedagainstthedrywallmaterial.
Congratulations, your speaker is now installed!
If you’ve decided not to paint the speaker grille, reinstall by pressing it into place along the top edge.
Gently work the grille into its recess on the speaker’s front panel by pressing the grille edges sequen-
tially until it is fully seated. A little patience here will go a long way! You may need to bend the grille
edges slightly to get a good t but do this carefully.
If you’ve decided to paint the grille, make sure you don’t clog the mesh. Too much paint or paint that’s
too thick will negatively affect your speakers’ sound.
© 2007 The Speaker Company. All rights reserved.
www.thespeakercompany.com
BREak-in
Many people believe speakers improve with age.
With TSC speakers, you’ll notice a change in timbre, responsiveness, and sheer musicality as you use
them because the drivers “settle in” with use.
How long should you wait? That depends, for example, on whether you listen AM radio at low volume
or full orchestral music at live concert levels. In general, you’ll begin to hear differences after 20-30
hours of use.
caRE
Your TSC In-Wall and In-Ceiling speakers don’t need much maintenance. Wipe them occasionally
with a damp cloth to keep the frame and grille clean.
Above all, enjoy! That’s what your TSC speakers were designed for and why we take such pride in
bringing them to you!