TSI Instruments DustTrak 8535 User manual

_______________
TSI and TSI logo are registered trademarks of TSI Incorporated. DustTrak is a trademark of TSI Incorporated.
Netronix and Thiamis are trademarks of Netronix Inc. Digi and XStream are trademarks of Digi International.
INSTALLATION GUIDE
INSTALLING THE NETRONIX™ THIAMIS™ 1000
GSM/GPS COMMUNICATION MODEM IN
THE ENVIRONMENTAL ENCLOSURE
MODEL 8535
This guide will help you quickly install the Netronix™
Thiamis™ 1000 GSM/GPS Communication Modem into
the Environmental Enclosure Model 8535.
Unpacking Netronix Thiamis
GSM/GPS Communication
Modem (801901)
1. Unpack the Netronix Thiamis GSM/GPS
Communication Modem (801901) for the
Environmental Enclosure (8535) and verify that all
the items listed in the following table are present.
2. Contact TSI immediately if items are missing
or broken.
Qty.
Item Description
Reference Picture
1
Adapter Plate
4
4-40 x 5/16” LG Pan Head
Screws
1
Power Cable
1
Spare Fuse
2
6-32 x 3/16” LG Pan
Head Screws
Qty.
Item Description
Reference Picture
1
NetronixThiamis GSM/GPS
Communication Modem
1
RS232 to USB Converter
Cable
1
Netronix Environet Quick
Start Guide
1
Environet Account Creation
Form
1
GSM/GPS Antenna
(not used)

-2-
Tools Needed for Installation
Qty.
Item Description
Reference Picture
1
Phillips Screw Driver
NOTE
It is assumed that the instrument, 12V DC external
power supply, water trap bottle and inlet tubing have
already been installed into the Environmental
Enclosure. In this guide, a DustTrak™DRX 8533EP
has been used. The water trap bottle, 12V DC power
supply and tubing are included with Environmental
Enclosure. See Environmental Enclosure 8535
Operation Manual for further details.
CAUTION
12V DC Power supply should not be connected to
power until instructed to do so.
NOTE
The 3G GSM/GPS Antenna is not needed for this
assembly. It is only needed when the modem is
installed inside a metal enclosure. The modem’s
built-in antenna will be able to acquire the cellular
signal through the 8535 Environmental Enclosure.
Installing the Netronix Thiamis
1000 GSM/GPS Communication
Modem
1. Using the
screw driver,
fasten the
adapter plate to
the base
bracket using
the 4-40 x
5/16” pan head
screws (qty. 4).
2. Remove the mounting
plate from the back of
the modem. To
separate the two
pieces, push the
button on the top of
the modem, rotate the
plate slightly away and
slide the mounting
plate downwards.
Be careful not to
rotate the plate too
far or the tabs on the
bottom may break.
3. Fasten the
mounting plate
to the adapter
plate using the
6-32 x 3/16” pan
head screws
(qty. 2).
4. Snap the
modem into the
mounting plate.

-3-
5. Using the
RS-232 to USB
cable, make a
connection
between the
DustTrak
monitor and the
modem. The
USB end should
connect to the
DustTrak
monitor. The
RS-232 end
should connect
to the modem.
6. Connect the
barrel end of the
power cable to
the DustTrak
monitor and the
black Phoenix
connector to the
modem. The
third connector
is for the heated
inlet control
module. If the
heated inlet is
not present, it
can left
unplugged.
7. Connect the other end to the power cable to the
power source. Same connection will be made if
using the solar power system accessory, instead
of the 12V DC power adapter.
8. Plug the
AC/DC power
supply into an
AC power
source.
Instrument and
modem should
power on.

TSI Incorporated –Visit our website www.tsi.com for more information.
USA Tel: [phone]
UK Tel: [phone]
France Tel: [phone]
Germany Tel: [phone]
India Tel: [phone]
China Tel: [phone]
Singapore Tel: [phone]
P/N 6007817 Rev D ©2017 TSI Incorporated Printed in U.S.A.
9. LED on the modem will blink while the modem
searches for a network. If the LED stops blinking
and is solid blue, a network has been found and
proper communication with Environet should be
possible. If the LED changes to solid yellow, the
modem has not found a network. A power cycle
may resolve the issue.
10. To utilize the telemetry functionality of Thiamis
1000, please refer to Netronix Environet Quick
Start guide. This guide is included in the
801901 kit.