TSI Instruments 5200 Series User manual

www.tsi.com
Gas Flow
Multi-Meter
5200 Series
Quick Start Guide
P/N 6012621, Revision C
May 2023

2 Quick Start Guide
Instrument Kit Components
5200 Series Low Flow Gas Multi-Meter
Qty
Item Description
Part/Model
1
Low Flow Gas Flow Multi-Meter, 3/8-inch tube ends
Measures Flow, Temperature, Absolute Pressure
5200
Low Flow Gas Flow Multi-Meter, 3/8-inch tube ends
Measures Flow, Volume, Temperature, Absolute
Pressure, Differential Pressure
5210
Low Flow Gas Flow Multi-Meter, 3/8-inch tube ends
Measures Flow, Volume, Temperature, Absolute
Pressure, Differential Pressure, Relative Humidity
5220
Low Flow Gas Flow Multi-Meter (High Accuracy),
3/8-inch tube ends, includes Tabletop Stand
Measures Flow, Volume, Temperature, Absolute
Pressure, Differential Pressure, Relative Humidity
5230
Low Flow Gas Flow Multi-Meter (Wide Accuracy Spec),
3/8-inch tube ends
Measures Flow, Temperature, Absolute Pressure
5203
1
Calibration Certificate
N/A
1
5200 Series Standard Accessory Kit
52000
1
Low Pressure Measurement Kit
(5210, 5220, 5230 models only)
5200-LPMK
1
License key for FLO-Sight™ PC Software
(Includes a free trial of the advanced version)
5000-PC
*FLO-Sight software can be downloaded from www.tsi.com.
Download Operator’s Manual at TSI.com

Gas Flow Multi-Meter 5200 Series 3
Instrument Overview
1. Power Button (On/Off)
5. USB-C Power/
Communications Port
2. Color Touchscreen Display*
6. USB-A Communications
Ports (2)
3. Interchangeable Tube Ends
7. Low Differential Pressure Ports
(5210/5220/5230 models only)
4. Mounting Inserts (M3 thread)
8. Collars
Dimensions shown in inches [mm]

4 Gas Flow Multi-Meter 5200 Series
Setup Basics
Supplying Power
Connect the USB cable from the USB-C port on the meter to the
USB-A port of: 1) the 5000 Series power supply, 2) a computer, or
3) other USB sources that can provide 5 VDC.
USB Hub Cable
Some computer USB ports are not capable of sufficiently powering up
the Meter. If you are unable to power your Meter from the computer,
connect the USBC-A power cable to the provided USB hub cable and
plug the hub cable into the computer.
Turning Meter ON/OFF
The Meter may power itself on when connected to a power source. If
not, press the power button to turn the Meter on. To turn the meter off,
press and hold the power button for 5 seconds.
Connect Inlet Filter
TSI®recommends an inlet filter be used at all times while operating the
Flow Multi-Meter.

Gas Flow Multi-Meter 5200 Series 5
Changing Tube Ends
1. Unscrew collars and remove tube ends.
2. Insert replacement tube ends into the meter while aligning the
anti-rotation locking notch on the tube end with the tab on
the meter.
3. Screw collars back onto the meter.

6 Gas Flow Multi-Meter 5200 Series
Touchscreen Display Overview
Meter Home Screen
1. Meter Home Tab
6. Volume and Triggers Tab *
2. Measurement Readings
7. Log Data Button *
3. Type of Gas
8. Menu Dropdown Screen
4. Flow Directional Indicator
9. Device Name and Information
5. Pause Display Button
10.Alerts Indicator
*Available on 5210, 5220, and 5230 models only
Pause Display Button
The Pause Button is used to pause the display from updating. The
current measurement values will remain fixed on the screen. The Meter
will continue to make measurements while paused, and pausing the
display does not affect any active datalog sessions.
When paused, the button’s icon will change to a play icon .
Press the button again to resume display updates.

Gas Flow Multi-Meter 5200 Series 7
Touchscreen Display Overview (continued)
Menu Screen
1. Go to Meter Home Screen
5. Rotate Display 180º
2. Set Logging Parameters *
6. Settings Menu
3. Data Management *
7. Press anywhere outside menu
to close menu screen
4. Reset Device Settings
*Available on 5210, 5220, and 5230 models only
Touchscreen Display
The touchscreen display is resistive and responds to pressure from
your finger or other objects. You can also operate the Meter while
wearing gloves.

8 Gas Flow Multi-Meter 5200 Series
Configuring the Meter
Measurement Parameters
Press a value field, use the scroll arrows to select a parameter, and
click Save.
Units of Measurement
Press a units field, use the scroll arrows to select the desired units, and
click Save.

Gas Flow Multi-Meter 5200 Series 9
Configuring the Meter (continued)
Type of Gas
Press the type of gas field, use the scroll arrows to select the type of
gas, and click Save.
NOTICE
If an Air/Oxygen mix is selected, the Meter assigns a 21%
oxygen mix. The oxygen concentration can be customized
using FLO-Sight™ Software.
Volume and Triggers
(Models 5210, 5220, and 5230 only)
Volume is a calculated measurement that integrates flow over time and
is controlled through triggers. You can set begin and end triggers for
volume measurements using flow rate, absolute pressure, or low
differential pressure values.
Setting Triggers
The meter must be stopped to edit trigger settings. On the Volume tab,
confirm that the Meter is stopped (shown below left) and press on the
field you would like to edit.
If a volume measurement is active (shown below right), then press the
Stop button to cancel the measurement and allow edits to be made
to trigger settings.

10 Gas Flow Multi-Meter 5200 Series
Volume and Triggers (continued)
In the Select Mode screen, you can choose:
Trigger Parameter
Flow, Absolute Pressure, or Low Pressure
Test Mode
Single or Continuous
Use the arrows to scroll through the selection options and click Save
to complete.
In the Select Trigger screens, you can choose:
Begin / End Trigger Values
Select from available values
Begin / End Trigger Slopes
Positive or Negative
Note trigger options for the volume begin and end triggers. These are
set as the default options and cannot be changed by the user.
Trigger
Units
Trigger Values
Flow
Std L/min
+/–0.1, 0.5, 1, 2, 3, 5, 7.5, 10, 20
Absolute Pressure
kPa
90, 95, 98, 100, 102, 104, 107, 110
Low Differential
Pressure
cmH2O
+/–0.5, 1, 2, 3, 4, 5, 10

Gas Flow Multi-Meter 5200 Series 11
Volume and Triggers (continued)
Making Volume Measurements
Once all settings have been saved, press the Play button to lock
editing and begin making volume measurements.
The Multi-Meter will notify you on screen when the begin trigger, and
then end trigger, is reached. Once the end trigger has been reached,
the Meter will deliver the volume measurement.

________________
TSI and TSI logo are registered trademarks of TSI Incorporated in the United States and may be
protected under other country’s trademark registrations.
TSI Incorporated –Visit our website www.tsi.com for more information.
USA Tel: [phone]
UK Tel: [phone]
France Tel: [phone]
Germany Tel: [phone]
India Tel: [phone]
China Tel: [phone]
Singapore Tel: [phone]
P/N 6012621 Rev C ©2023 TSI Incorporated Printed in U.S.A.