TTS TEMPO Manual

DIRECTIONS FOR USE
TEMPO TRAFIC LIGHT
Z.I. 1ère Avenue 2ème Rue BP 594 06516 Carros cedex –Tél : [phone] –Fax : [phone]
www.ttsys.eu
A0031DD71004D-User Guide

SWITCH OFF
CAUTIONS
CONTROL MANAGEMENT
Control Management with remote control
Selection of the different modes by successive pression on the +ou –(mode) user-defined keys.
To avoid any damage, and when the equipment will not be used for a longer
period (more than a month), disconnect the batteries and accumulators from the
yellow cupola, from the remote control and from the battery box.
Periodically control the batteries used_by dates.
FORCING MODES
Control Management
with pushing button
Selection of the different modes by successive pression on the button
For the handling of the traffic light, or its accessories such as the
battery, the use of PPE is mandatory (gloves, glasses and safety
shoes).
*The setting of the various user modes described in this manual always starts with the same step.
TRAFFIC LIGHT OPERATING
Display
when
switched
on
Battery voltage ■Turn on the Tempo traffic lights by
connecting the battery placed in the battery
box.
■At that time, the Tempo traffic light is in a
waiting state « central orange light flashing ».
POWER ON
TTS-Tempo-2 2016
001-V-100
FEUX: 12,0V
CLIGNOTANT M
In order to become familiar with the programming
procedure, it is advisable to test the configuration of
the lights in the workshop, before putting them into
service on site.
-Fixed cycle
-Uneven traffic
-Free cycle
-Crossroad 3T
-Crossroad 3X
-Crossroad 4T
-Crossroad 4X
-Flashing orange
-Stand by
-Red only
-Fixed cycle when traffic light is programmed
otherwise « not synchrinized » displayed
2
Press down the push button for 5 seconds
without disconnecting the battery.
RESET
Disconnect the + battery
terminal and press down the
push the button for 5 seconds.

Traffic Length 100m 200m 300m 400m 500m 600m
Full RED 12’’ 22’’ 32 ’’ 42’’ 52’’ 62’’
Low Traffic
(2000 cars/jour) Yellow 20’’ 20’’ 20’’ 24’’ 28’’ 32’’
Medium Traffic
(2 to 5000 cars/jour) Yellow 30’’ 30’’ 36’’ 46’’ 54’’
Heavy Traffic
(5 to 8000 cars/jour) Yellow 44’’ 66’’ 90’’ 112’’
Very Heavy Traffic
(8 to 11000 cars/jour) Yellow 130’’
•Times are given in seconds.
•The crossed out sections represent impossible traffic combinations, in an alternating 2 lights
configuration on a work site.
Length 100m 200m 300m 400m 500m 600m
Full RED 12’’ 22’’ 32 ’’ 42’’ 52’’ 62’’
Heavy Traffic
(5 à 8000 véh./jour)
Yellow with
traffic 30’’ 44’’ 58’’ 72’’
Yellow against
traffic 20’’ 24’’ 32’’ 38’’
Very Heavy Traffic
(8 to 11000 cars/jour)
Yellow with
traffic 46’’ 72’’ 98’’
Yellow against
traffic 26’’ 38’’ 50’’
Traffic Limit
(11 to 14000 cars/jour)
Yellow with
traffic 86’’
Yellow against
traffic 45’’
With traffic
Against traffic
REGLEMENTARY WAITING TIME SCALE
3
*Full red = Time when both lights are red.
Waiting time = 2x full red + yellow
2 LIGHTS ALTERNATING PROGRAMMING - UNBALANCED TRAFFIC
2 LIGHTS ALTERNATING PROGRAMMING - BALANCED TRAFFIC

Displayed
when
switch on
Battery voltage
■Turn on the Tempo traffic lights by
connecting the battery placed in the battery
box.
■At that time, the Tempo traffic light is in a
waiting state « central orange light flashing ».
■Select the density of the traffic with the +
and -(select) user-defined keys.
(please refer to the time table page 3)
■Validate.
You must hear a double BEEP.
■Select the length between the two traffic light
with the + and -(select) user-defined keys.
(Se référer au tableau des temps page3)
■Validate.
Selection Validation
▼
▲
Traffic programming
LOW
AVERAGE
HEAVY
VERY HEAVY
■Switch on the remote control
■Direct it to the window display symbol
Selection Validation
STEP 3
Roadwork length programming
▼
▲100m
200m
300m
400m
500m
600m
Validation
STEP 4
Validation of the cycle on the 2nd traffic light
Traffic light1
Switch on
STEP 1
STEP 2
TTS-Tempo-2 2016
001-V-100
LIGHT: 12,0V
FLASHING M
FIXED CYCLE
TRAFFIC: LOW
FIXED CYCLE
LENGHT:100m
FIXED CYCLE 12,0V
100m LOW m
FIXED CYCLE 12,0V
100m LOW a
Traffic light2
SWITCH OFF
■Disconnect the + battery terminal
and maintain pression on the button
during 5 seconds.
ALTERNATE PROGRAMMING 2 TRAFFIC LIGHTS
4
■Go to the 2nd traffic light
■Direct the remote control to the window
display symbol
■Validate.
You must hear a double BEEP.
until the LCD screen goes off.

Selection Validation
Selection Validation
▼
▲■Select if the traffic is more or less heavy on
this side with +and -(select) user-defined
keys.
■Validate.
One side heavy traffic programming
LOAD +
LOAD -
Selection Validation
STEP 3
Traffic programming
■Select the uneven density of the traffic with
the +and -(select) user-defined keys.
(please refer to the time table page 3)
■Validate.
▼
▲HEAVY
VERY HEAVY
LIMIT
Selection Validation
STEP 4
Roadwork length programming
■Select the length between the two traffic light
with the +and -(select) user-defined keys.
■Validate.
You must hear a double BEEP.
Validation
STEP 5
Validation of the cycle on the 2nd traffic light
Traffic light 1
Mode selection
STEP 1
STEP 2
LIGHT: 12,0V
FLASHING M
CYCLE:
UNEVEN
DIRECTION
TRAFFIC:LOAD
UNEVEN
TRAFFIC:HEAVY
UNEVEN
LENGHT:100m
UNEVEN + 12,0V
100m HEAVY m
Traffic light 2
UNEVEN -12,0V
100m HEAVY a
The traffic load setting is done on the 1st
light:
LOAD + : Light 1- for more dense traffic.
LOAD - : Light 1 - for less dense traffic.
▼
▲100m
200m
300m
UNBALANCED TRAFFIC PROGRAMMING
5
Traffic is more important
on a traffic axis.
■Select « Uneven » mode with the +and -
(mode) user-defined keys.
■Validate.
■Switch on the remote control
■Direct it to the window display symbol
You must hear a double BEEP.
■Go to the 2nd traffic light
■Direct the remote control to the window
display symbol
■Validate.

Selection Validation
Selection Validation
▼
▲■Select the lenght of the roadwork using the +
and -(select) user-defined keys.
■Validate.
Traffic lenght programming
100m
200m
300m
…
2000m
Selection Validation
STEP 3
Traffic light 1 time programming
■Select the flashing time of the 1st light on the
1st traffic light using the +and -(select) user-
defined keys.
■Validate.
▼
▲5s
10s
15s
…
120s
Selection Validation
STEP 4
Traffic light 2 time programming
■Select the flashing time of the 2nd light on the
1st traffic light using the +and -(select) user-
defined keys.
■Validate.
You must hear a double BEEP.
Validation
STEP 5
Validation of the cycle on traffic light 2
Starting mode
STEP 1
STEP 2
FEUX: 12,0V
FLASHING M
CYCLE:
FREE
FREE
LENGHT:100m
FREE
YELLOW 1: 45s
FREE
YELLOW 2: 20s
FREE 12,0V
100m 45s 20s m
FREE 12,0V
100m 45s 20s a
▼
▲5s
10s
15s
…
120s
FREE PROGRAMMING
6
The passage time for each light is configurable.
The length of the site is adjustable up to 2000m.
■Select « Free » mode with the +and -
(mode) user-defined keys.
■Validate.
■Switch on the remote control
■Direct it to the window display symbol
■Go to the 2nd traffic light
■Direct the remote control to the window
display symbol
■Validate.
You must hear a double BEEP.
Traffic light 1
Traffic light 2

Selection Validation
Selection Validation
▼
▲■Select the redlight timing with the +and -
(select) user-defined keys.
■Validate.
Red light programming
5s
10s
15s
…
60s
Selection Validation
STEP 3
Traffic light 1 green light
programming
■Select the green light timing (flashing
orange) of the 1st traffic light with the +and -
(select) user-defined keys.
■Validate.
▼
▲5s
10s
15s
…
60s
Selection Validation
STEP 4
Traffic light 2 green light
programming
■Select the green light timing (flashing
orange) of the 2nd traffic light with the + and -
(select) user-defined keys.
■Validate.
You must hear a double BEEP.
▼
▲5s
10s
15s
…
60s
Validation
STEP 5
Repeat this operation for the third light.
Validation of the cycle on traffic lights 2 and 3
Traffic
light 1
Traffic
light 2
Traffic
light 3
Mode selection
STEP 1
STEP 2
LIGHT: 12,0V
FLASHING M
CYCLE:
CROSSROAD 3T
CROSSROAD 3T
RED:25s
CROSSROAD 3T
GREEN 1:10s
CROSSROAD 3T
GREEN 2:15s
CROSSROAD 12,0V
3T GREEN:25s P1m
CROSSROAD 12,0V
3T GREEN:25s P2a
CROSSROAD 12,0V
3T GREEN:25s P3a
Repeat this step for the light n°3.
Each light turns green one after the other Axe 1
Axe 2
Traffic
light 3
Traffic
light 1
Traffic
light 2
3 LIGHTS ALTERNATE CROSSROAD PROGRAMMING
7
■Select « Crossroad 3T » mode with the +
and -(mode) user-defined keys.
■Validate.
■Switch on the remote control
■Direct it to the window display symbol
■Go to the 2nd traffic light
■Direct the remote control to the window
display symbol
■Validate.
You must hear a double BEEP.

Selection Validation
Selection Validation
▼
▲
■Select the red light timing with the +and -
(select) user-defined keys.
■Validate.
Red light programming
5s
10s
15s
…
60s
Selection Validation
STEP 3
Axis 1 green light programming
■Select the green light timing (flashing
orange) of the 1st axis with the +and -(select)
user-defined keys.
■Validate.
▼
▲5s
10s
15s
…
60s
Selection Validation
STEP 4
Axis 2 green light programming
■Select the green light timing (flashing
orange) of the 2nd axis with the +and -(select)
user-defined keys.
■Validate.
You must hear a double BEEP.
▼
▲5s
10s
15s
…
60s
Validation
STEP 5
Mode selection
STEP 1
STEP 2
LIGHT: 12,0V
FLASHING M
CYCLE:
CROSSROAD 3X
CROSSROAD 3X
RED:25s
CROSSROAD 3X
AXE 1:10s
CROSSROAD 3X
AXE 2:10s
CROSSROAD 12,0V
3X GREEN:25s P1m
CROSSROAD 12,0V
3X GREEN:25s P2a
CROSSROAD 12,0V
3X GREEN:25s P3a
Axe 1
Axe 2
Lights 1 and 3 have the same color (axis 1).
Light 2 (axis2) is opposite axis 1.
3 LIGHTS AXIS CROSSROAD PROGRAMMING
8
■Select « Crossroad 3X » mode with the +
and -(mode) user-defined keys.
■Validate.
■Switch on the remote control
■Direct it to the window display symbol
Repeat this operation for the third light.
Validation of the cycle on traffic lights 2 and 3
7
You must hear a double BEEP.
Traffic
light 1
Traffic
light 2
Traffic
light 3
Traffic
light 3
Traffic
light 1
Traffic
light 2
■Go to the 2nd traffic light
■Direct the remote control to the window
display symbol
■Validate.

4 LIGHTS ALTERNATE CROSSROAD PROGRAMMING
Each light turns green one after the other
Selection Validation
Selection Validation
■Select the red light timing with the +and -
(select) user-defined keys.
■Validate.
Red light programming
Selection Validation
STEP 3
Traffic light 1 green light
programming
■Select the green light timing (flashing
orange) of the 1st traffic light with the + and -
(select) user-defined keys.
■Validate.
▼
▲5s
10s
15s
…
60s
Selection Validation
STEP 4
Traffic light 2 green light
programming
■Select the green light timing (flashing
orange) of the 2nd traffic light with the +and -
(select) user-defined keys.
■Validate.
You must hear a double BEEP.
▼
▲5s
10s
15s
…
60s
Validation Repeat this operation for the third and
fourth light.
Traffic
light 1
Traffic
light 2
Traffic
light 3
Traffic
light 4
STEP 1
STEP 2
LIGHT: 12,0V
FLASHING M
CYCLE:
CROSSROAD 4T
CROSSROAD 4T
RED:25s
CROSSROAD 4T
GREEN 1:10s
CROSSROAD 4T
GREEN 2:15s
CROSSROAD 12,0V
4T GREEN:25s P1m
CROSSROAD 12,0V
4T GREEN:25s P2a
CROSSROAD 12,0V
4T GREEN:25s P3a
CARREFOUR 12,0V
4T GREEN:25s P4a
Axe 1
Axe 2
Traffic
light 3
Traffic
light 1
Traffic
light 4
Traffic
light 2
Repeat this step for the light n°3 and n°4.
▼
▲5s
10s
15s
…
60s
9
Mode selection
■Select « Crossroad 4T » mode with the +
and -(mode) user-defined keys.
■Validate.
■Switch on the remote control
■Direct it to the window display symbol
STEP 5
Validation of the cycle on traffic lights 2, 3 and 4
You must hear a double BEEP.
■Go to the 2nd traffic light
■Direct the remote control to the window
display symbol
■Validate.

Lights 1 and 3 have the same color (axis 1)
The light 2 and 4 (axis 2) have the same color
and are opposite the axis 1.
Selection Validation
Selection Validation
▼
▲
Red light programming
5s
10s
15s
…
60s
Selection Validation
STEP 3
Axis 1 green light programming
■Select the green light timing (flashing
orange) of the 1st axis with the +and -(select)
user-defined keys.
■Validate.
▼
▲5s
10s
15s
…
60s
Selection Validation
STEP 4
Axis 2 green light programming
■Select the green light timing (flashing
orange) of the 2nd axis with the +and -(select)
user-defined keys.
■Validate.
You must hear a double BEEP.
▼
▲5s
10s
15s
…
60s
Validation
STEP 5
STEP 2
LIGHT: 12,0V
FLASHING M
CYCLE:
CROSSROAD 4X
CROSSROAD 4X
RED:25s
CROSSROAD 4X
AXE 1:10s
CROSSROAD 4X
AXE 2:20s
CROSSROAD 12,0V
4X GREEN:25s P1m
CROSSROAD 12,0V
4X GREEN:25s P2a
CROSSROAD 12,0V
4X GREEN:25s P3a
CROSSROAD 12,0V
4X GREEN:25s P4a
Axe 1
Axe 2
4 LIGHTS ALTERNATE CROSSROAD PROGRAMMING
10
STEP 1
Mode selection
■Select « Crossroad 4X » mode with the +
and -(mode) user-defined keys.
■Validate.
■Switch on the remote control
■Direct it to the window display symbol
■Select the red light timing with the +and -
(select) user-defined keys.
■Validate.
Repeat this operation for the third and
fourth light.
Validation of the cycle on traffic lights 2, 3 and 4
■Go to the 2nd traffic light
■Direct the remote control to the window
display symbol
■Validate.
You must hear a double BEEP.
Traffic
light 1
Traffic
light 2
Traffic
light 3
Traffic
light 4
Traffic
light 3
Traffic
light 1
Traffic
light 4
Traffic
light 2

11