Turbosound MILAN MI5 User manual

USER GUIDE
Turbosound Ltd
Star Road, Partridge Green
West Sussex RH13 8RY United Kingdom
Tel: [phone] Fax: [phone]
web: www.turbosound.com
Issue 1.0 © Turbosound Ltd

user manual
MILAN
MILAN user manual
Page 2
Contents
USER GUIDE ................................................................................................................................................................... 1
Contents .......................................................................................................................................................................... 2
EC Declaration of Conformity.................................................................................................................... 4
Safety considerations................................................................................................................................ 5
Introduction ................................................................................................................................................ 6
Thanks.........................................................................................................................................................................6
Unpacking ..................................................................................................................................................................6
Contents .................................................................................................................................................................6
Getting Started ........................................................................................................................................... 7
Self-Powered Loudspeakers..................................................................................................................... 8
Signal Flow Block Diagram .....................................................................................................................................8
Bass Mode.................................................................................................................................................. 9
Using Milan with Subwoofers ............................................................................................................................9
Using Milan as a Floor Monitor..........................................................................................................................9
Model Information.................................................................................................................................... 10
Milan MI5 Self-Powered Loudspeaker...........................................................................................................10
Milan MI5 Features ............................................................................................................................................11
Connector wiring...................................................................................................................................... 12
Connecting to the Milan MI5................................................................................................................... 13
1. Mains Connector and Fuseholder ...............................................................................................................13
2. Mains Switch...................................................................................................................................................13
3. Signal Input......................................................................................................................................................13
4. Mic / Line Switch ............................................................................................................................................13
5. Level Control....................................................................................................................................................13
6. Bass Control and 7. Treble control ..............................................................................................................13
8. Bass Mode switch..........................................................................................................................................14
9. Mix Out .............................................................................................................................................................14
10. Power Indicator ............................................................................................................................................14
11. Signal Indicator.............................................................................................................................................14
12. Limit indicator................................................................................................................................................14
Connection Diagrams .............................................................................................................................. 15
Small band setup using the integrated mixer and Mix Out.........................................................................15
Stereo PA with an external mixer....................................................................................................................16
Stereo PA with an external mixer and subwoofer(s)...................................................................................17
Stereo PA with powered wedge monitors.....................................................................................................18
Loudspeaker Placement.......................................................................................................................... 19
Installing the Milan loudspeaker............................................................................................................ 20
Using the M10 rigging points............................................................................................................................20
Wall Mounting.....................................................................................................................................................20
Troubleshooting ....................................................................................................................................... 21
Product Dimensions................................................................................................................................. 22
Milan MI5 .............................................................................................................................................................22
Technical Specifications......................................................................................................................... 23

user manual
MILAN
MILAN user manual
Page 3
Spare Parts................................................................................................................................................24
Accessories ............................................................................................................................................................ 24
Warranty ....................................................................................................................................................25
Contact Information..................................................................................................................................26
Customer Service................................................................................................................................................... 26
Product Information............................................................................................................................................... 26
Notes..........................................................................................................................................................27

user manual
MILAN
MILAN user manual
Page 4
EC Declaration of Conformity
Manufacturer
Turbosound Ltd, Star Road, Partridge Green, West Sussex, RH13 8RY, UK
tel: [phone] fax: [phone] www.turbosound.com
Products:
Milan MI5
Standards:
Relevant Specifications used as basis for tests EN55103-1:1996
Directive 1999/5/EC
Category
Professional apparatus for use in Commercial Light Industrial and controlled EMC environments.
CE Marking
All products are marked in accordance with the relevant statutory requirements.
Signatories
Simon Blackwood (Managing Director)
Dominic Harter (Sales Director)
July 2009

user manual
MILAN
MILAN user manual
Page 5
Safety considerations
Before using your Milan loudspeaker please read the following information as it pertains to your
safety and the reliability of your product.
1. Read and retain these instructions.
2. Heed all warnings.
3. Follow all instructions.
4. Do not use this product near water.
5. Do not install near any heat sources such as radiators, stoves, boilers, or other apparatus
that produces heat.
6. Do not allow the mains cable to become damaged, twisted, cut or caught under other
equipment.
7. Do not use the loudspeaker with AC mains supplies lower than 100v or higher than 240v,
as damage may result.
8. Use only accessories and attachments approved by the manufacturer. If the product is to
be permanently installed use only rigging hardware approved by Turbosound.
9. Unplug the loudspeaker during lightning storms or when it is not to be used for long
periods of time.
10. This equipment must be grounded (earthed).
11. Be careful when lifting the loudspeaker, for instance when placing onto speaker stands or
poles. Make sure that you are lifting within your personal capability.
12. Keep the exterior of the loudspeaker enclosure clean, and clean only with a dry cloth.
13. Do not install the loudspeaker in outdoor environments where the product could be
subjected to moisture, excessive temperatures or prolonged UV light exposure.
Electrically powered devices such as this product can present dangerous shock hazards
when wet or exposed to moisture.
14. This product is not suitable for fixed installation in outdoor environments.

user manual
MILAN
MILAN user manual
Page 6
Introduction
Congratulations, you have purchased a professional loudspeaker product from the Milan series of
loudspeakers, designed to give you the best in audio quality and many years of reliable, trouble-
free operation. It offers excellent pattern control, safe and practical rigging hardware, superior
audio quality, proven reliability, ease of setup, consistent performance, and the backing of a world
leader in acoustics technology including a comprehensive warranty against manufacturing
defects. Please read through this manual carefully before you attempt to operate the loudspeaker
system. It contains valuable information which will enable you to quickly and easily connect the
loudspeakers to your outboard equipment; and important system and set-up checks.
Thanks
Thank you for choosing a TURBOSOUND loudspeaker product for your application.
By engaging in an on-going rigorous program of research and development all TURBOSOUND
products are carefully engineered for world class performance and reliability.
If you would like further information about this or any other TURBOSOUND product, please
contact us. Detailed product information is available on our website at: www.turbosound.com
We look forward to helping you in the near future.
Unpacking
After unpacking the unit please check carefully for damage. If damage is found, please notify the
carrier concerned at once. You, the consignee, must instigate any claim. Please retain all
packaging in case of future re-shipment.
Contents
Milan MI5 loudspeaker
IEC mains cable
User Guide
Turbosound logo sticker

user manual
MILAN
MILAN user manual
Page 7
Getting Started
LINE LINEMIC MIC
BASS TREBLE MIX OUT
BASS
MODE
LIMIT
-6dB
POWER
_
0
+_
0
+
LEVEL INPUT 1 INPUT 2 LEVEL
MIN MAX MIN MAX
AB
1. Turn the level controls fully anticlockwise (MIN) on both input channels.
2. Set the Bass and Treble tone controls to their centre position (no boost or cut).
3. Connect your signal sources (mixing console, keyboard, microphone, acoustic guitar) to
the input connectors and select MIC or LINE as appropriate for that source.
4. If the loudspeaker is to be used as a floor monitor, or for use with subwoofers, set the
BASS MODE switch to the ‘B’ position; otherwise select the ‘A’ position.
5. Switch on the mixer or other source and make sure the output faders or master output
level controls are turned fully down.
6. Connect the AC mains cable to the Milan loudspeaker and turn on the mains switch. The
blue POWER LED will illuminate to indicate that mains power is connected.
7. Increase the output level of the signal source to a normal operating level.
8. Slowly turn up the Milan loudspeaker’s level control(s) until a suitable volume level is
reached. The green SIGNAL LED illuminates when the input signal is -6dB from limiting.
It is normal for the LIMIT LED to flash occasionally, but excessive or prolonged
illumination indicates that the input signal is too high or additional speakers are required.
9. When shutting down the Milan system, first turn down the input level controls, then
switch off the mains power before turning off the mixer or signal source.

user manual
MILAN
MILAN user manual
Page 8
Self-Powered Loudspeakers
Milan series self-powered loudspeakers are equipped with an integrated Class D amplifier module,
taking consistent performance, convenience and ease of use to a new level. Featuring lightweight
high-power amplifiers using 48kHz DSP and operating at better than 90% efficiency, Milan
eliminates the need for separate amplifier racks and controllers, as well as the attendant cabling.
This makes setting up at gigs and obtaining a consistent sound in different venues a faster and
simpler process.
The amplifier is exactly matched to the known parameters of the loudspeaker components, and is
therefore able to produce the optimum power for the drivers. By placing the amplifier in the
cabinet it is possible to keep the loudspeaker cables extremely short to eliminate resistive losses,
so effectively all the power from the amplifier is transferred to the drivers.
The availability of on-board electronics provides an opportunity to build in a two-channel mixer
offering both mic and line inputs with two band EQ and sophisticated DSP-based limiting. These
fast-acting, frequency-dependent limiters allow you to achieve higher average sound pressure
level, reduce the possibility of driver damage, and help to ensure better long-term system
reliability.
A professional quality crossover network filters the low and high frequencies appropriately to each
driver, to ensure that each is working in its optimum frequency band. The high-grade circuit
components ensure that every loudspeaker performs consistently.
Due to the extremely high efficiency and modern, high performance power supply, the Milan
amplifier module only adds less than 2 kilos to the overall net weight of the loudspeaker, and this
is an important factor in portable applications where the loudspeaker is to be transported and set
up frequently in a variety of venues.
Signal Flow Block Diagram
+TREBLE
LEVEL
TO 20dB
MIC +24.6dB
LINE -3.5dB
LEVEL
TO 20dB
MIC +24.6dB
LINE -3.5dB
JACK
CHANNEL 2
XLR
JACK
CHANNEL 1
XLR
BASS
LEVEL
DETECT
CLIP/LIMIT
MIX OUT
-6dB
VOICED
HIGH PASS
BASS
MODE
PARAMETRIC
EQ
USER EQ
DYNAMIC
PROTECTION AMPLIFIER
TREBLE BASS
1
2
3
1
2
3
1
2
3

user manual
MILAN
MILAN user manual
Page 9
Bass Mode
The BASS MODE switch introduces a 100Hz filter in the bass part of the frequency response. In the
‘B’ position it allows better integration of sub-bass loudspeakers with Milan MI5 loudspeakers by
preventing an overlap in the bass frequencies. The subjective result is extended bass response.
If you are using Milan without subwoofers we recommend that you select the ‘A’ position, which
will ensure the frequency response is unaffected.
Using Milan with Subwoofers
Improved bass response and higher overall sound pressure level can be achieved by adding sub-
bass loudspeakers to the Milan system. This also reduces mechanical stress on the Milan
loudspeaker’s low frequency driver, since most of the low frequency content in the signal is routed
to the subwoofer.
It is recommended that you connect the full range signal from the mixer
first to the subwoofer(s), and from there to the Milan MI5. Make sure the
BASS MODE switch is correctly selected to the ‘B’ position.
When using non-powered subwoofers, take a separate output from the
mixer and run it to the sub-frequency amplifier(s). Connect directly from the
mixer outputs to the Milan loudspeaker as in the example without
subwoofers, but select the ‘B’ position on the BASS MODE switch to allow
the majority of low frequencies to be handled by the subwoofers.
Using Milan as a Floor Monitor
You can select the ‘B’ position on the BASS MODE switch when using Milan
as a floor monitor, which will avoid any low frequency boominess due to
the proximity of the floor that can detract from clear and intelligible monitor
sound.
If you are using Milan as part of a larger multi-channel monitor system and
where drums may be part of the monitor mix, BASS MODE ‘A’ can be
selected provided that kick drum EQ is used sparingly and carefully.

user manual
MILAN
MILAN user manual
Page 10
Model Information
Milan MI5 Self-Powered Loudspeaker
The Milan MI5 is a self-powered sound reinforcement
loudspeaker designed for many different portable and
permanently installed applications.
It consists of a 450 watt program 15” neodymium low
frequency driver, matched with a 1” neodymium high
frequency compression driver on a 90°horizontal x 60°
vertical horn, together with a Class D amplifier module
providing two input channels and on-board DSP.
The low frequency driver is a custom-designed 15” unit
using a 2.5” voice coil driven by a neodymium ring
magnet. The custom-developed 1” exit HF compression
driver feeds a wide dispersion Converging Elliptical
Waveguide for smooth and even coverage over a wide
audience area.
These high quality professional components are
housed in a lightweight, stylish and durable trapezoidal
moulded polypropylene cabinet that is instantly
adaptable to front-of-house or floor monitoring
applications. The cabinet is extensively ribbed and
internally damped. This design feature increases the
cabinet’s rigidity and eliminates internal reflections, which translates into better transient
response and improved bass reproduction. It also keeps the weight of the cabinet as low as
possible.
Milan is equipped with a dual angle pole mount socket which allows it to be angled down for
better coverage when used with tripod stands or for mounting on top of bass cabinets. Lifting and
carrying is made easy with the provision of built-in handles on the sides, as well as a scoop handle
on the top of the cabinet.
The Milan cabinet provides M10 rigging points on the top and bottom for suspending horizontally
or vertically in permanent installs.

user manual
MILAN
MILAN user manual
Page 11
Milan MI5 Features
•450 watt lightweight digital Class D amplifier for excellent audio quality
•Internal DSP with frequency-dependent limiting ensures long term reliability
•Integrated mixer provides two input channels each with microphone and line inputs via
combination jack/XLR connectors
•Two-band EQ with 12dB of cut and boost on both input channels
•Mix Out function allows daisy-chaining of Milan loudspeakers and simple expansion of
your sound system
•Trapezoidal shape with symmetrical 43°wedge angle allows the loudspeaker to be used
as a floor monitor
•Ergonomically placed aluminium handles for easy lifting and carrying
•Professional quality 1” high frequency compression driver with wide dispersion
Converging Elliptical Waveguide
•Custom developed 15” LF driver with neodymium magnet assembly provides high
performance and contributes to lower weight
•Dual angle pole mount socket allows the loudspeaker to be used vertically or angled
downwards for improved coverage
•Durable, stylish and lightweight moulded composite enclosure
•Internal M10 rigging points for easy suspension in permanent installs
•Attractive powder coated and galvanised perforated steel grille

user manual
MILAN
MILAN user manual
Page 12
Connector wiring
The amplifier inputs are designed to accept balanced (three conductor) connections, and it is
recommended that this method be used since it offers the best rejection of noise, hum and radio
interference, especially where long cable runs are involved. XLR connectors should be wired pin 2
hot, while the standard wiring for 3-pole jack plug connectors is tip hot (+ve) and ring cold (-ve) as
shown below.
ground
hot
cold
ground
hot
cold
Balanced male XLR Balanced female XLR
Some signal sources such as keyboards, acoustic guitars with on-board electronics, and some
microphones commonly provide only an unbalanced output on a 2-pole jack connector. The Milan
loudspeaker can handle these connections without any rewiring since pin 3 (-ve) of the input is
automatically grounded by the jack plug.
3-pole jack (balanced) sleeve - ground
tip - hot
ring - cold
2-pole Jack (unbalanced)
ground
tip - hot
cold
If an unbalanced source is to be connected to an input channel via the XLR input connector, either
2-pole or 3-pole jack plugs can be used. In both cases pin 3 should be connected to pin 1 (ground)
at the XLR as shown here.
1 (ground)
2
3
tip
ring
sleeve
1 (ground)
2
3
tip
sleeve
Some sources such as mp3 players or CD players commonly provide 2-pole unbalanced phono
connectors, and these can be connected to a Milan input channel via either the XLR connector or
jack connector. In either case wire the connectors as follows:
1 (ground)
2
3
tip
sleeve
tip
sleeve
tip
sleeve

user manual
MILAN
MILAN user manual
Page 13
Connecting to the Milan MI5
1. Mains Connector and Fuseholder
Mains power is connected to the loudspeaker via a
combination IEC connector and fuseholder. The power supply
is auto-sensing and can be connected to mains supplies
ranging from 110 volts to 240 volts AC without the need to
change any settings.
2. Mains Switch
Rocker switch turns mains power on to the loudspeaker. Make
sure the level controls are fully off (MIN) before switching on.
3. Signal Input
These combo female XLR/jack connectors accept both XLR
connectors and mono (2 pole) or stereo (3 pole) ¼” jack plugs
for use with a variety of balanced and unbalanced
microphones, instruments and line sources. The inputs are
balanced to avoid hum loops and RF interference, and are
wired pin 2 hot, pin 3 cold.
4. Mic / Line Switch
Selects the input for that channel to accept either a low level,
low impedance microphone, or a high level, high impedance
source such as a mixing console, keyboard or acoustic
instrument with onboard electrics. The mic input is not suitable
for condenser microphones that require phantom power.
5. Level Control
Rotary level control which attenuates the input signal level of
the connected instrument / line source for that input channel.
The range (mic) is from -∞(MIN) to +16.5dB (MAX) and (line)
from -∞(MIN) to +40.6dB (MAX).
6. Bass Control and 7. Treble control
The bass control provides ±12dB of shelving at 200Hz, and the
treble control provides ±12dB of shelving at 4kHz. Always use
equalisation sparingly, aiming to cut rather than boost
especially when the loudspeaker is used near boundaries such
as walls or floors.
LINE LINEMIC MIC
BASS TREBLE MIX OUT
BASS
MODE
LIMIT
-6dB
POWER
_
0
+_
0
+
LEVEL INPUT 1 INPUT 2 LEVEL
MIN MAX
FUSE T10AL
REPLACE ON LY WITH SAME
TYPE AND R ATING OF FUSE
MIN MAX
POWER
100-230V
450Wmax 50-60Hz
ON
AB
2
1
5
6 7 8 9
5
4334

user manual
MILAN
MILAN user manual
Page 14
8. Bass Mode switch
This slide switch introduces a fourth order high-pass filter in the lower part of the frequency
response at 100Hz, and is useful to avoid boominess due to proximity to the floor when the Milan
loudspeaker is used as a floor monitor. The bass mode high-pass should also be selected when
the Milan MI5 is used with sub-bass loudspeakers. This allows bass frequencies to be routed
appropriately to the sub-bass speakers, avoiding an overlap between these and the Milan MI5, and
giving greater clarity and definition to the overall sound.
9. Mix Out
A balanced line level output on a balanced male XLR that connects to additional powered Milan
loudspeakers. This output contains a mix of all connected sources and is post-EQ, although it is
independent of the bass mode switch. Note that adjusting the equalisation will similarly affect any
additional Milan loudspeakers connected from this output.
10. Power Indicator
Illuminates blue to indicate that mains power is connected and powered up.
11. Signal Indicator
Illuminates green when the signal level reaches -6dB, and is a useful indicator of the input signal
approaching the limiter threshold.
12. Limit indicator
Illuminates red when the signal level approaches maximum and the limiters start working.
Frequent and/or continuous lighting of limit LED indicates overdriving. If this occurs reduce the
input level to the loudspeaker or enlarge your system with additional loudspeakers.

user manual
MILAN
MILAN user manual
Page 15
Connection Diagrams
Small band setup using the integrated mixer and Mix Out
The built in two channel mixer allows the simultaneous use of either two low impedance dynamic
microphones, a microphone and line level source, or two line level sources. The line level source
could be an acoustic instrument such as a guitar with either passive or active on-board electrics, a
keyboard, or MP3 player. Connect a dynamic mic directly to either of the combo jack/XLR input
connectors, switch the MIC/LINE switch to MIC and adjust the volume level. Connect line sources
to either of the combo jack/XLR connectors, switch the MIC/LINE switch to LINE and adjust the
volume control. More mics and sources can be connected by using the MIX OUT function to daisy-
chain to additional Milan loudspeakers.
LINE LINEMIC MIC
BASS TREBLE MIX OUT
BASS
MODE
LIMIT
-6dB
POWER
0
+
0
+
LEVEL INPUT 1 INPUT 2 LEVEL
MIN MAX MIN MAX
AB
LINE LINEMIC MIC
BASS TREBLE MIX OUT
BASS
MODE
LIMIT
-6dB
POWER
0
+
0
+
LEVEL INPUT 1 INPUT 2 LEVEL
MIN MAX MIN MAX
AB

user manual
MILAN
MILAN user manual
Page 16
Stereo PA with an external mixer
Two Milan loudspeakers form the left and right elements of a stereo PA setup with all signal
sources connected to an external mixing console. Ensure that the mic/line switch is set to LINE on
both loudspeakers. Set the BASS MODE switch to the ‘A’ position when not using subwoofers.
Bring up the master faders on the mixer, ensuring that the outputs are not clipping, and then
adjust both loudspeakers’ level controls to the desired loudness. For consistent balance and
response set the tone controls to approximately the same positions on both cabinets.
LINE LINEMIC MIC
BASS TREBLE MIX OUT
BASS
MODE
LIMIT
-6dB
POWER
0
+
0
+
LEVEL INPUT 1 INPUT 2 LEVEL
MIN MAX MIN MAX
AB
LINE LINEMIC MIC
BASS TREBLE MIX OUT
BASS
MODE
LIMIT
-6dB
POWER
0
+
0
+
LEVEL INPUT 1 INPUT 2 LEVEL
MIN MAX MIN MAX
AB
LEFT RIGHT

user manual
MILAN
MILAN user manual
Page 17
Stereo PA with an external mixer and subwoofer(s)
In this example, sub frequencies are routed to a separate subwoofer(s) in order to gain extended
frequency response and higher overall sound level. Connect the mixer output first to the
subwoofers and then loop up to the Milan loudspeakers. Set the MIC/LINE switch to LINE and set
the BASS MODE switch to the ‘B’ position to roll off the low frequencies to the Milan MI5
loudspeakers. The tone controls on both cabinets should be set to the same positions, nominally
flat to begin with. Ensure that the mixer outputs are not clipping, and then adjust both
loudspeakers’ level controls to the desired loudness.
POWERED
SUB-BASS
POWERED
SUB-BASS
LINE LINEMIC MIC
BASS TREBLE MIX OUT
BASS
MODE
LIMIT
-6dB
POWER
0
+
0
+
LEVEL INPUT 1 INPUT 2 LEVEL
MIN MAX MIN MAX
AB
LINE LINEMIC MIC
BASS TREBLE MIX OUT
BASS
MODE
LIMIT
-6dB
POWER
0
+
0
+
LEVEL INPUT 1 INPUT 2 LEVEL
MIN MAX MIN MAX
AB

user manual
MILAN
MILAN user manual
Page 18
Stereo PA with powered wedge monitors
On larger gigs a separate monitor system provides good quality foldback for individual performers
and helps to keep the PA sound less cluttered. Select the BASS MODE ‘A’ or ‘B’ position as
required on the Milan monitors.
LINE LINEMIC MIC
BASS TREBLE MIX OUT
BASS
MODE
LIMIT
-6dB
POWER
0
+
0
+
LEVEL INPUT 1 INPUT 2 LEVEL
MIN MAX MIN MAX
AB
LINE LINE MIC
BASS TREBLE MIX OUT
BASS
MODE
LIMIT
-6dB
POWER
0
+
0
+
LEVEL INPUT 1 INPUT 2 LEVEL
MIN MAX MIN MAX
AB
LINE LINEMIC MIC
BASS TREBLE MIX OUT
BASS
MODE
LIMIT
-6dB
POWER
0
+
0
+
LEVEL INPUT 1 INPUT 2 LEVEL
MIN MAX MIN MAX
AB
LINE LINEMIC MIC
BASS TREBLE MIX OUT
BASS
MODE
LIMIT
-6dB
POWER
0
+
0
+
LEVEL INPUT 1 INPUT 2 LEVEL
MIN MAX MIN MAX
AB
LEFT
MON1
RIGHT
MON2

user manual
MILAN
MILAN user manual
Page 19
Loudspeaker Placement
In order to avoid the possibility of feedback locate the loudspeakers in front of your microphones
and do not point microphones directly at the front of a loudspeaker.
When using speaker stands, try to raise the loudspeakers as high as
practically possible (at least higher than the heads of the audience) since
people are very good absorbers of sound,
especially at high frequencies. You also
have the option to point them down using
the alternate angle provided for by the built-
in dual angle pole holder. Doing this will
improve the coverage for both near and far
audience members.
SAFETY PRECAUTIONS: make sure that any
speaker stands you use are capable of
taking the weight of the loudspeaker, and
that stands are placed on a flat, level and
stable surface. Make sure that the legs do
not present a trip hazard. Take care when
lifting the speakers on to the stand; ask
someone else to help you if needed.
The same applies to using Milan
loudspeakers mounted on straight poles on
top of bass cabinets or subwoofers.
Adjustable height poles or stands allow you
to fine tune the height of the loudspeakers
to suit your venue.
Do not place your loudspeakers too close to
turntables as this may induce rumble or low
frequency feedback from the tone arms.
Isolate turntables on shock mounts.
Use equalisation sparingly. Start with the bass and treble controls at their neutral position (no
boost or cut). Cut a little bass to tame any boomy frequencies in the room, and add a little treble to
help vocal intelligibility.
Consider adding subwoofers and/or further loudspeakers if the overall sound level or low
frequency response is not enough for the room.

user manual
MILAN
MILAN user manual
Page 20
Installing the Milan loudspeaker
Using the M10 rigging points
The Milan loudspeaker can be permanently installed in a venue,
suspended from eyebolts fitted to the internal M10 rigging points
on the top and bottom of the cabinet. Three possible orientations
are available: vertically upright, or upside down to position the high
frequency driver closer to the audience, or sideways if required.
Insert M10 load-rated shoulder eyebolts
into the threaded rigging points and
tighten. The front rigging points should
take the majority of the load while the rear
rigging point should be used for angling
the cabinet downwards only.
When installing the
cabinet sideways,
pick up from either of
the two front eyebolt
pairs, and bridle the two rear eyebolt points to
provide a single pull-back for adjusting the
downward angle.
Wall Mounting
The Milan loudspeaker can be conveniently wall mounted using the PB-55 pole mount wall
bracket, which simply locates into the pole mount socket in the bottom of the cabinet.
Mount the bracket to the wall using suitable fixings, and locate the loudspeaker onto the pole
mount bracket. Rotate and angle the loudspeaker to optimise coverage and tighten the locking
mechanism to stop the loudspeaker from being inadvertently removed.