TV Logic LUM-095G User manual

Operation manual_V1.1
LUM-095G
4K/UHD
Multi-Purpose Monitor

FCC (Federal Communications Commission)
This equipment has been tested and found to comply with the limits for class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interface when the equipment is operated in a commercial environment.
This equipment generates, uses and can radiate radio frequency energy and if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential to correct the interference at his own expense
CAUTION: Change or modications not expressly approved by the manufacturer responsible for
compliance could void the user’s authority to operate the equipment.
Disposal of Old Electrical & Electronic Equipment
(Applicable in the European Union and other European countries with separate collection systems)
This symbol on the product or on its packing indicates that this product shall not be treated as
household waste.
Instead it shall be handed over to the applicable collection point for the recycling of electrical and
electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequence
for the environment and human health, which could otherwise be caused by inappropriate waste
handling of this product. The recycling of materials will help to conserve natural resources.

01
02
03
04
05
06
07
08
09
04p
06p
07p
11p
12p
12p
13p
16p
17p
20p
22p
23p
29p
31p
39p
41p
Caution
Main Features
Controls & Functions
Menu Tree & Adjustment
Menu Operations
[1] PICTURE
[2] COLOR
[3] MARKER
[4] DISPLAY / VIDEO
[5] WAVEFORM
[6] AUDIO
[7] SYSTEM / GPI / UMD
Button Functions
Other Functions
Video Support Resolution
Product Specications
Contents

01 CAUTION
4
4K/UHD Multi-Purpose Monitor
4
• Make sure to connect the power supply of the
specied voltage value: DC 12V/24V MAX 2.3A.
• When using a DC Adapter other than the one
supplied by the manufacturer, please be advised
that the adapter with DC 12V/24V MAX 2.3A can
be compatible with the monitor.
• All operating instructions must be read and
understood before the product is operated.
• These safety and operating instructions must be
kept in safe place for future reference.
• All warnings on the product and in the instructions
must be observed closely.
• All operating instructions must be followed.
• Do not use attachments not recommended by the
manufacturer. Use of inadequate attachments
can result in accidents.
• This product must be operated on a power
source specied on the specication label.
• If you are not sure of the type of power supply
used in your home, consult your dealer or local
power company. For units designed to operate
on batteries or another power source, refer to the
operating instructions.
• The power cords must be routed properly to
prevent people from stepping on them or objects
from resting on them. Check the cords at the
plugs and product.
• In case of using other 12V DC adapters instead of
the standard adapter provided by the manufacturer,
please check the proper load capacity (or current
capacity) and use an adapter with stable voltage.
• Do not overload DC outlets or extension cords.
Overloading can cause or electric shock.
• Never insert an object into the product through
vents or openings. High voltage in the product,
and inserting an object can cause electric shock
and/or short internal parts. For the same reason,
do not spill water or liquid on the product.
• Do not attempt to service the product yourself.
Removing covers can expose you to high voltage
and other dangerous conditions. Request a
qualied service person to perform servicing.
• If any of the following conditions occurs, unplug
the power cord from the DC outlet, and request a
qualied service person to perform repairs.
a. When the power cord or plug is damaged.
b. When a liquid was spilled on the product or
when objects have fallen into the product.
c. When the product has been exposed to rain or
water.
d. When the product does not operate properly as
described in the operating instructions. Do not
touch the controls other than those described
in the operating instructions.
Improper adjustment of controls not described
in the instructions can cause damage, which often
requires extensive adjustment work by a
qualied technician.
e. When the product has been dropped or
damaged.
f. When the product displays an abnormal
condition.
Any noticeable abnormality in the product
indicates that the product needs servicing.
• In case the product needs replacement parts,
make sure that the service person uses replacement
parts specied by the manufacturer, or those with
the same characteristics and performance as the
original parts. Use of unauthorized parts can
result in re, electric shock and/or other danger.
• Upon completion of service or repair work, request
the service technician to perform safety checks to
ensure that the product is in proper operating
condition.
• When mounting the product on a wall or ceiling,
be sure to install the product according to the
method recommended by the manufacturer.
• Unplug the power cord from the DC outlet before
cleaning the product. Use a damp cloth to clean
the product. Do not use liquid cleaners or aerosol
cleaners.
• Unplug the power cord from the AC outlet if you
do not use the product for considerably long time.

01 CAUTION
5
4K/UHD Multi-Purpose Monitor
• Do not use the product near water, such as bathtub,
washbasin, kitchen sink and laundry tub,
swimming pool and in a wet basement.
• Keep the product away from direct rays of the
Sun-light.
• Do not place the product on an unstable cart,
stand, tripod or table. Placing the product on an
unstable base can cause the product to fall,
resulting in serious personal injuries as well as
damage to the product. Use only a cart, stand,
tripod, bracket or table recommended by the
manufacturer or sold with the product. When
mounting the product on a wall, be sure to follow
the manufacturer’s instruction. Use only the
mounting hardware recommended by the
manufacturer.
• When relocating the product placed on a cart, it
must be moved with the utmost care.
• The power cord plug shall be connected to a
MAINS socket outlet with a protective earthing
connection.
• Infrared devices can cause noise or malfunction
under condition as below.
- Parts of the body come into contact with the
infrared transmiter or acoustic device.
- Obstacles can cause electrical changes if there is
a partition in the middle or in the wall.
- Exposure to radio interference from medical
equipment, microwave ovens, wireless LAN
devices, etc. with the same frequency band.
• Unplug the power cord from the AC outlet when
happening any problem in the product.
• Sudden stops, excessive force and uneven oor
surface can cause the product to fall from the cart.
• The vents and other openings in the cabinet are
designed for ventilation. Do not cover or block
these vents and openings since insucient
ventilation can cause overheating and/or shorten
the life of the product. Do not place the product
on a bed, sofa, rug or other similar surface, since
they can block ventilation openings. This product
is not designed for built-in installation; do not
place the product in an enclosed place such as a
bookcase or rack, unless proper ventilation is
provided or the manufacturer’s instructions are
followed.
• In case of installation the product on the rack, the
inside of the product would be overheated due to
heat from other devices near by and the decrease
of air circulation, which could damage to the
monitor. To prevent the damage, please have
enough space for the monitors and use fan to
avoid heat and maintain the operating temperature.
(Refer to the specication of the product).
• The LCD panel used in this product is made of
glass. Therefore, it can break when the product is
dropped or applied with impact. Be careful not to
be injured by broken glass pieces in case the LCD
panel breaks.
• Keep the product away from heat sources such as
radiators, heaters, stoves and other heat generating
products (including ampliers).
• If the still image is displayed on the screen in the
same position for a long period of time, the
permanent burn-in on the LCD panel may occur. So,
do not display characters or markers continuously.
If the video signals or image patterns are
continuously displayed at the maximum or high
level of luminance, the image smearing or icker
may occur on the screen because of the LCD
panel’s structure and characteristics of materials used.
When the permanent burn-in, image smearing, or
other damages happen on the LCD panel due to the
improper use by the end user, the warranty service is
not applied.

02 MAIN FEATURES
6
4K/UHD Multi-Purpose Monitor
LUM-095G Monitor contains the following features
• Audio Level Meter
- Displays the level of the embedded audio
signal together with the video signal input
through SDI and HDMI.
- Level Meter channel number(16ch, 8ch, 4ch)
and direction(horizontal, vertical) adjustable
- Level Meter grouping available
- Audio channel Pair or Group selectable
- Level Meter size(Small, Large) changeable
• Video Range Adjustment: Limited 109%, Full
• Various Marker
• Grid Display: 3x3, 4x4, 5x5, 6x6
• Timecode Display: LTC, VITC
• ARRI Camera Status: LDS Info, Index Letter
• Scan: Zero Scan, Over Scan, 1:1 Scan
• User Aspect
• H Flip, V Flip, H/V Flip: Manual, Auto
• Focus Assist
• Dynamic UMD Display
• H/V Delay
• Blue/Mono Only
• Various Aspect: 16:9, 4:3, 2.35:1, 1.85:1, 15:9,
16:10
• Anamorphic: 1.3X, 1.5X, 1.8X
• Luma(Y’) Zone Check
• Range Error
• Closed Caption: CC-608, CC-708
• Zoom: 10%, 20%, ..., 90%
• Zoom Split: Left-Top, Right-Top, Left-Bottom,
Right-Bottom, Center
• Freeze
• Internal Pattern Display
• Tally Lamp and Screen Tally
• Remote Control via RS-422(RJ-45)
• GPI Control via REMOTE port
• Firmware Update & Calibration via USB(A Type)
• DC 12V to 24V supported
• Various 4K/UHD Video Input Interface
- 12G-SDI Single Link Input
- 3G-SDI Quad Link Square Division Input
- 3G-SDI Quad Link 2-Sample Interleave Input
- HDMI 2.0 Input
• HDR Emulation
- Supports various HDR EOTF such as PQ, HLG,
S-Log3
• IPS LCD Panel
- Oers the wide viewing angle with IPS
technology
• Easy & Simple Control
- Various OSD Key buttons and Input Signal
Indicators on the front panel
• Custom 3D LUT Import
- Allows the users to load their own created 3D
LUT les generated by color grading tools and
apply them to the monitor.
• Integrated Camera LUT
- LUTs for every major camera manufacturers are
integrated to the LUM-095G, and they can be
applied to the live input video.
- Log-C, C-Log, S-Log1, S-Log2, S-Log3, RED
Gamma 3, RED Gamma 4
• Advanced Color Adjustment OSD
- Provides various color adjustment menus
which enable the user to monitor the video
signal in the optimal settings.
• Waveform & VectorScope
- Provides various modes: Waveform,
VectorScope, Waveform Wide, Waveform YCbCr,
Waveform RGB, Waveform&VectorScope,
Waveform YCbCr&VectorScope, Waveform Full,
VectorScope Full

03 CONTROLS & FUNCTIONS
7
4K/UHD Multi-Purpose Monitor
LUM-095G ALL PART (FRONT / REAR)
SPEAKER-RIGHT
F3
DOWN
F2
ENTER
POWER
H/V DELAY
MARKER
W-FORM/VECTOR
BLUE/MONO
ASPECT
SCAN
VOLUME
CONTRAST
MENU
UP
SPEAKER-LEFT
APERTURE
BRIGHT
CHROMA
SDI
HDMI
TALLY
TALLY
F1
TALLY
REMOTE
USB
DC IN
SDI-IN A/B
SDI-OUT C/D
RS-422 IN
RS-422 OUT
AUDIO IN
AUDIO OUT
HDMI

03 CONTROLS & FUNCTIONS
8
4K/UHD Multi-Purpose Monitor
FRONT
• [SDI] Button/Lamp
- Used to select SDI-A/B input.
• [HDMI] Button/Lamp
- Used to select HDMI input.
• [SCAN] Button/Lamp
- Used to change the scan mode.
- Press the button to activate through the scan
modes: [ZERO SCAN] -> [OVER SCAN] ->
[1:1 SCAN] -> [USER ASPECT]
*[USER ASPECT]: User can adjust width and
height of the display.
*Check“7. Other Functions [1] User Aspect”
for more information.
• [ASPECT] Button/Lamp
- Used to change the various display ratio.
Activates in order of [16:9] -> [4:3] -> [2.35:1] ->
[1.85:1] -> [15:9] -> [16:10] -> [ANAMORPHIC
1.3X] -> [ANAMORPHIC 1.5X] -> [ANAMORPHIC
1.8X] -> [AUTO]
• [MARKER] Button/Lamp
- Used to activate/deactivate the Marker.
The type of marker at work can be selected on
the main menu.
• [H/V DELAY] Button/Lamp
- Used to check horizontal sync and vertical
sync simultaneously by moving the display
left, right, up and down.
- In this mode, the brightness of the image
automatically increase for easy verication of
synchronized signals.
• [BLUE]/[MONO] Button/Lamp
- Activates in the order of [O]-[Blue Only]-
[Mono]-[O]
- Press the button to remove red and green
from the input signal and display the screen
only under a blue signal. Press the button
again to activate mono mode.
• [W-FORM/VECTOR] Button/Lamp
- Used to activate/deactivate the Waveform.
- The type of Waveform at work can be selected
on the main menu.
• [F1][F2][F3] Button/Lamp
- Used to activate the [F1]~[F3] function.
*Check“6. Button Functions [5] Function Key Set
Button”for more information.

03 CONTROLS & FUNCTIONS
9
4K/UHD Multi-Purpose Monitor
FRONT
• [MENU] Button
- Used to activate the OSD menu.
- When the OSD menu is activated, press this
button to exit from the menu.
• [UP] / [DOWN] Button
- Used to move within the menu when the OSD
menu is activated and is also used to increase
or decrease the value of selected feature.
• [ENTER] Button
- Used to select the feature of main menu and
the sub menus.
• [POWER] Switch
- Used to turn the power on and o.
• [POWER INDICATOR] Lamp
- Indicates condition and power status of unit.
- Light turns o when the power is disconnected.
- Standby mode is indicated by a red LED light.
- Normal (active) mode is indicated by a Green
LED light.
- The Green light turns o when the monitor is
Normal(active) mode without input signal.
• [TALLY] Lamp
- Tally lamp that can be toggled in green or
red using the REMOTE(RJ-45) port or RS-422
serial communication.
• [APERTURE] Knob
- Used to adjust the picture sharpness.
- The value is selectable between -12 ~ 12.
• [BRIGHT] Knob
- Used to adjust the degree of brightness.
- The value is selectable between -100 ~ 100.
• [CHROMA] Knob
- Used to adjust the saturation of the image.
- The value is selectable between -50 ~ 50.
• [CONTRAST] Knob
- Used to adjust the contrast.
- The value is selectable between -100 ~ 100.
• [VOLUME] Knob
- Used to adjust the volume for internal speaker
and external output.
- The value is selectable between 0 ~ 30.

03 CONTROLS & FUNCTIONS
10
4K/UHD Multi-Purpose Monitor
REAR
• USB
- This terminal is used to upgrade the rmware
or color calibration made by TVLogic.
• REMOTE (RJ-45)
- Used to form a parallel switch and control the
monitor externally.
- Features can be changed in the [SYSTEM / GPI /
UMD] section of OSD menu.
• DC IN (XLR, 4 pins)
- DC power input terminal for DC 12V/24V.
* When using a DC Adapter other than the one
supplied by the manufacturer, please be
advised that the adapter with DC 12V/3A ~ 6A
can be compatible with the monitor.
• [SDI IN-A (12G)] (BNC)
- 12G/HD/SD SDI signal input
• [SDI IN-B (3G)] (BNC)
- HD/SD SDI signal input
• [SDI IN-C / SDI OUT] (BNC)
- HD/SD SDI signal input(for Quad-Link 4K/UHD
input) or 12G/HD/SD SDI Through Out for
SDI A input
• [SDI IN-D / SDI OUT] (BNC)
- HD/SD SDI signal input(for Quad-Link 4K/UHD
input) or 12G/HD/SD SDI Through Out for
SDI B input
• [HDMI IN]
- HDMI signal input
• [RS-422 IN/OUT]
- Used for the control of the monitor with
protocol provided by TVLogic or for Dynamic
UMD function by TSL protocol.
• [AUDIO IN] (Phone Jack)
- Insert the external stereo audio signal.
• [AUDIO OUT] (Phone Jack)
- The audio signal which is disembedded from
SDI or HDMI input signal or the external audio
signal which is inserted to [AUDIO IN] is output
through the phone jack.
<WARNING!!>
When using the product make sure to ground,
whenever possible, before connecng the
input signal cable in order to prevent any
possible damage to the product or connected
devices. The damage may include signal noise,
malfuncon of main board or display panel.
And the connected devices such as camera or
video source player may also be inuenced
through signal cable. Please check if the AC
power source and the power extender or
power distributor is grounded.
DC IN
socket
1: GND
4: +12V/
+24V
1
2
3
4

04 MENU TREE & ADJUSTMENT
MENU TREE & MENU CONTROL & MENU CONTROL SEQUENCE
11
4K/UHD Multi-Purpose Monitor
• OSD(On-Screen Display) Menu helps to use
various dierent functions.
•This Picture is the menu structure for LUM-095G.
[1] MENU TREE [3] MENU CONTROL SEQUENCE
[2] MENU CONTROL
• User may control various functions using the
MENU button and the Knob on the top of the
monitor.
• Menu control sequence follows the order below.
1. Press MENU button to activate the OSD menu.
2. Move to a desired menu using the Knob.
3. Press the Knob to select a menu and move to
select a sub-menu by scrolling the Knob.
4. Press the Knob to select the desired sub menu.
(The selected sub-menu will be highlighted)
5. Press the ENTER button or the MENU button
to save the new value after adjusting the value
by scrolling the Knob.
6. Press MENU button to return to previous menu
and if there is no previous menu, the OSD menu
will be removed from the screen.
UNLOCK
REC 709
SYNCHRONIZATION
NONE 1
NONE 1
NONE 1
PICTURE 같이 LUM-095G
BRIGHTNESS
CONTRAST
CHROMA
SHARPNESS
PEAKING BOOST
KNOB LOCK
3DLUT LOAD
3DLUT SYNC
3DLUT IMPORT 1
3DLUT IMPORT 2
3DLUT IMPORT 3
+90
+90
+40
0
0

05 MENU OPERATIONS
12
4K/UHD Multi-Purpose Monitor
[1] PICTURE
UNLOCK
REC 709
SYNCHRONIZATION
NONE 1
NONE 1
NONE 1
PICTURE 같이 LUM-095G
BRIGHTNESS
CONTRAST
CHROMA
SHARPNESS
PEAKING BOOST
KNOB LOCK
3DLUT LOAD
3DLUT SYNC
3DLUT IMPORT 1
3DLUT IMPORT 2
3DLUT IMPORT 3
+90
+90
+40
0
0
• BRIGHTNESS
- Used to set the brightness(=oset) level from
-100 to 100.
* Brightness can be adjusted by using [UP] and
[DOWN] button on the front of the monitor.
• CONTRAST
- Used to set the contrast(gain) level from
-100 to 100.
* Contrast can be adjusted by using [UP] and
[DOWN] button on the front of the monitor.
• CHROMA
- Used to set the saturation level from -50 to 50.
* Chroma can be adjusted by using [UP] and
[DOWN] button on the front of the monitor.
• SHARPNESS
- Used to set the Sharpness level from 0 to 24.
* Sharpness can be adjusted by using [UP]
and [DOWN] button on the front of the
monitor.
• PEAKING BOOST
- Used to set the Peaking Boost level from 0 to 24.
* Peaking Boost can be adjusted by using
[UP] and [DOWN] button on the front of
the monitor.
• KNOB LOCK
- Locks the Knob control.
• 3DLUT LOAD
- Used to apply the internally stored 3DLUT.
- Maximum 3 x 3DLUT les can be stored.
- The le name can be set up to 20 characters
including the extension.
• 3DLUT SYNC
- Used to load a list of available 3DLUT les
currently stored in the FLASH MEMORY.
- Available 3DLUT formats are Cube, GV Lut,
Quantel, Davinci and Assimilate Scratch.
- Available sizes of the 3DLUT are 17 or 33.
• 3DLUT IMPORT 1/2/3
- Used to save the 3DLUT stored in the external
memory to the internal memory 1/2/3 area.
- Once saved, the 3DLUT can be maintained even
when the power is turned ON/OFF.
- The le name can be set up to 20 characters
including the extension.

05 MENU OPERATIONS
13
4K/UHD Multi-Purpose Monitor
[2] COLOR
COLOR같이 LUM-095G
STANDARD
VIDEO RANGE
PEAK LUMINANCE
BLACK LEVEL
COLOR GAMUT
COLOR TEMP
EOTF
LOCAL DIMMING
EETF
HLG SG
SG
CAM LUT
UHD
LIMITED109
100
0.001
BT.2020
6500K
2.4
OFF
OFF
OFF
OFFc
PAGE (1/2)
• STANDARD
- Used to select the color and dynamic range of
the screen.
- Available options are HD, UHD, DCI-P3, PQ, HLG,
SLog3 and User1/2/3.
• VIDEO RANGE
- Used to select the range of digital video signal.
- [FULL]: Input signal 1~254(8bit), 4~1019(10bit)
- [LIMITED109]: Input signal Y': 16~254, CbCr:
16~240(8bit) / Y': 64~1019, CbCr: 64~1019(10bit)
*Activates only in [STANDARD - USER 1/2/3] mode.
• PEAK LUMINANCE
- Used to select the Peak Luminance of the
monitor.
- Selectable levels are [100] ~ [1000] with 100
increment, [1000] ~ [10000] with 1000 increment.
*Activates only in [STANDARD - USER 1/2/3] mode.
• BLACK LEVEL
- The minimum black level of the video signal
can be set dierently depending on the
performance of the monitor or the lighting
environment.
- Available modes are from [0.000] to [0.010] with
0.001 increment, from [0.010] to [0.100] with
0.010 increment, from [0.100] to [0.900] with
0.100 increment.
* Activates only in the User1/2/3 mode.
• COLOR GAMUT
- Used to select the standard color gamut.
- Available options are BT709, DCI, BT2020,
NATIVE.
* Activates only in [STANDARD - USER 1/2/3]
mode.
• COLOR TEMP (Color Temperature)
- Controls the color temperature.
- Available options are 6500K, 9300K, USER 1/2/3.
* Activates only in [STANDARD - USER 1/2/3]
mode.
• EOTF (Electro-Optical Transfer Function)
- Electrophotic conversion Functions(ex: Gamma
or HDR curve).
- Available modes are 2.2, 2.4, 2.6, PQ, HLG and
SLOG3.
* Activates only in [STANDARD - USER 1/2/3]
mode.
• LOCAL DIMMING (* Not Supported)
- Used to set the Local Dimming Backlight mode.
- This mode is supported by the local dimming
backlight model and does not support F-7HS.

05 MENU OPERATIONS
14
4K/UHD Multi-Purpose Monitor
[2] COLOR
• EETF (Electrical-Electrical Transfer Function)
- Used to display the HDR image(without clipping)
within the actual luminance range (black level
and peak luminance) that the monitor can
express. In the ON mode, the HDR image is
converted within the range of set peak luminance
and black level. In the OFF mode, the video
signal outside of the set range is clipped.
- Available modes are OFF and ON.
- Available only when the EOTF is set to PQ or
SLOG3.
* Activates only in [STANDARD - USER 1/2/3]
mode.
• HLG SG (HLG System Gamma)
- Used to set the System Gamma of HLG mode.
- In the ON mode, the value of the System
Gamma changes automatically according to the
previously set peak luminance. When it is OFF,
the value is set to default value of 1.2.
* Activates only when the EOTF is set to HLG.
and STANDARD is set to USER 1/2/3.
• SG (System Gamma)
- The System Gamma of HLG is automatically
calculated and displayed according to the set
[PEAK LUMINANCE].
- Activates only when the EOTF is set to HLG and
the HLG SG is ON.
COLOR같이 LUM-095G
STANDARD
VIDEO RANGE
PEAK LUMINANCE
BLACK LEVEL
COLOR GAMUT
COLOR TEMP
EOTF
LOCAL DIMMING
EETF
HLG SG
SG
CAM LUT
UHD
LIMITED109
100
0.001
BT.2020
6500K
2.4
OFF
OFF
OFF
OFF
PAGE (1/2)
• CAM LUT (Camera LUT)
- Used to change the Camera LUT.
- Available LUTs are LOG-C, C-LOG, S-LOG1,
S-LOG2, S-LOG3, REDGAMMA3, REDGAMMA4.
* Activates only when STANDARD is set to USER
1/2/3], and EOTF is set to 2.2, 2.4, 2.6.
PEAK LUMINANCE SG (System Gamma)
100 0.78
200 0.91
300 0.98
400 1.03
500 1.07
600 1.11
700 1.13
800 1.16
900 1.18
1000 1.20
2000 1.33
3000 1.40
4000 1.45
5000 1.49
6000 1.53
7000 1.55
8000 1.58
9000 1.60
10000 1.62

05 MENU OPERATIONS
15
4K/UHD Multi-Purpose Monitor
[2] COLOR
COLOR같이 LUM-095G
COLOR TEMP
GAIN RED
GAIN GREEN
GAIN BLUE
BIAS RED
BIAS GREEN
BIAS BLUE
COLOR COPY
COLOR SPACE
6500K
6500K
BT.709
+ 0
+ 0
+ 0
+ 0
+ 0
+ 0
PAGE (2/2)
• COLOR COPY
- Used to copy the R/G/B Gain value of pre-stored
color temperature settings.
- In User mode, nd and select the color
temperature and press the Knob to copy and
apply the Gain value to GAIN RED, GAIN GREEN,
GAIN BLUE.
* Available only in User 1/2/3 mode.
• COLOR SPACE
- Used to select the standard color space.
- Available options are BT.709, DCI, BT.2020,
NATIVE.
• COLOR TEMP
- Controls the color temperature and allows
instant access to preset the color temperature
settings.
- Available color temperatures are 6500K, 9300K
and User1/2/3.
* In User 1/2/3 modes, user can dene custom
RGB GAIN, BIAS (=Oset) and Color Copy values.
• GAIN RED / GREEN / BLUE
- Used to set Red/Green/Blue Gain (or Picture,
Contrast) level from -256 to 255.
* Available only in User 1/2/3 mode.
• BIAS RED / GREEN / BLUE
- Used to set Red/Green/Blue Bias (or Oset,
mainly aects on Black level) from -100 to 100.
* Available only in User 1/2/3 mode.

05 MENU OPERATIONS
16
4K/UHD Multi-Purpose Monitor
[3] MARKER
MARKER같이 LUM-095G
ENABLE
MARKER
CENTER MARKER
SAFETY AREA
FIT MARKER
MARKER MAT
MARKER COLOR
THICKNESS
USER MARKER H1
USER MARKER H2
USER MARKER V1
USER MARKER V2
GRID ENABLE
GRID TYPE
GRID THICKNESS
GRID TRANS
ON
OFF
OFF
OFF
OFF
OFF
WHITE
2
OFF
OFF
1
OFF
+ 0
+1920
+ 0
+1080
• ENABLE
- Used to activate the Marker function.
• MARKER
- Available Marker types are OFF, 16:9, 4:3, 4:3 ON
AIR, 15:9, 14:9, 13:9, 1.85:1, 2.35:1, 1.85:1& 4:3 and
USER.
• CENTER MARKER
- Displays the Center Marker on the screen.
• SAFETY AREA
- Used to select and controls the size and
availability of the Safety Area.
- Available sizes are 80%, 85%, 88%, 90%, 93%,
100%, EBU ACTION 16:9, EBU GRAPHIC 16:9, EBU
ACTION 14:9, EBU GRAPHIC 14:9, EBU ACTION 4:3
and EBU GRAPHIC 4:3.
• FIT MARKER
- Used to activate or inactivate the Fit Marker
function.
- When the Marker type is selected in the Marker
menu, a border line of the Safety Area will be
displayed inside the Marker. Images below show
the dierence between Fit Marker ON and OFF.
• MARKER MAT
- Used to set the darkness level outside of the
MARKER area from OFF(transparent) to 7(Black).
- The bigger the value, the darker the color.
• MARKER COLOR
- Used to set the color of the MARKER lines.
- Available colors are WHITE, YELLOW, CYAN,
GREEN, MAGENTA, RED, BLUE, BLACK.
• THICKNESS
- Used to set the thickness of the MARKER lines.
- Thickness level is from 1 to 7 by the pixel unit.
• USER MARKER H1
- Used to set the position of the rst horizontal
marker line.
- Displayed when the MARKER menu is set to
USER.
• USER MARKER H2
- Used to set the position of the second horizontal
marker line.
- Displayed when the MARKER menu is set to
USER.
• USER MARKER V1
- Used to set the position of the rst vertical
marker line.
- Displayed when the MARKER menu is set to
USER.
• USER MARKER V2
- Used to set the position of the second vertical
marker line.
- Displayed when the MARKER menu is set to
USER.
• GRID ENABLE
- Used to activate the GRID lines.
• GRID TYPE
- Available grid types are 3X3, 4X4, 5X5, 6X6.
• GRID THICKNESS
- Used to set the thickness of the grid lines.
- Thickness level is from 1 to 5 by the pixel unit.
• GRID TRANS
- Used to set the transparency level of the grid lines.
- [ON]: transparent
- [OFF]: opaque
MARKER : 4:3
SAFETY AREA : 90%
FIT MARKER : OFF
MARKER : 4:3
SAFETY AREA : 90%
FIT MARKER : ON

05 MENU OPERATIONS
17
4K/UHD Multi-Purpose Monitor
[4] DISPLAY / VIDEO
VIDEO이 LUM-095G
SCAN
ASPECT
H/ V DEL AY
BLUE ONLY
USER ASPECT HOR
USER ASPECT VER
3G FORMAT
H/V FLIP
ZOOM
ZOOM SPLIT
CCAPTION
CC INFO
CHANNEL (608)
SERVICE (708)
ZERO SCAN
AUTO
OFF
OFF
NORMAL
OFF
OFF
OFF
OFF
CC 1
SERVICE 1
+1920
+1080
PAGE (1/2)
• SCAN
- Used to change the Scan mode.
- Available modes are ZERO SCAN, OVER SCAN,
1 : 1 SCAN, USER ASPECT
* [1 :1 SCAN] : When the UHD(3840x2160) or
4K(4096 x 2160) image is fed, this function
displays the image pixel to pixel on the screen
whose panel resolution is 1920 x 1080.
See section "7. Other Functions [1] 1 : 1 SCAN
* [USER ASPECT] : User can control the aspect
ratio by adjusting width and height of the display.
• ASPECT
- Used to change the Aspect Ratio.
- Regardless of the original Aspect ratio of the
input signal, the Aspect Modes are changed as
follow sequence. : [Auto][16:9][4:3][2.35:1][1.85:1]
[15:9][16:10][Anamorphic1.3x][Anamorphic1.5x]
[Anamorphic1.8x]
* [Auto] mode enables the Aspect Ratio of the
output signal to be synchronized to the original
Aspect Ratio of the input signal.
• H/V DELAY
- Used to monitor the Blanking area of H sync and
V sync.
• BLUE ONLY
- Available modes are [OFF] [BLUE ONLY] [MONO].
-[BLUEONLY]:Removeredandgreencomponents
from the input signal and display blue componet
only.
- [MONO] : Used to remove the color(Chroma) from
the input signal and display the monochrome
component only.
• USER ASPECT HORIZONTAL/USER ASPECT
VERTICAL
- Activated only when the [SCAN] mode is set to
[User Aspect].
- User can adjust the Horizontal and Vertical size
of the screen.
- See section “7. Other Functions [2] User Aspect"
for more information.

05 MENU OPERATIONS
18
4K/UHD Multi-Purpose Monitor
[4] DISPLAY / VIDEO
VIDEO이 LUM-095G
SCAN
ASPECT
H/ V DEL AY
BLUE ONLY
USER ASPECT HOR
USER ASPECT VER
3G FORMAT
H/V FLIP
ZOOM
ZOOM SPLIT
CCAPTION
CC INFO
CHANNEL (608)
SERVICE (708)
ZERO SCAN
AUTO
OFF
OFF
NORMAL
OFF
OFF
OFF
OFF
CC 1
SERVICE 1
+1920
+1080
PAGE (1/2)
• 3G FORMAT
- Used to select 3G-SDI A/B input format.
[NORMAL]
[A 444 10BIT YCbCr], [A 444 10BIT RGB]
[A 444 12BIT YCbCr], [A 444 12BIT RGB]
[A 422 12BIT YCbCr], [B 444 10/12BIT YCbCr]
[B 444 10/12BIT RGB], [B 422 12BIT YCbCr]
[B 422 10BIT YCbCr 60P]
- In NORMAL MODE, automatically detected when
Payload signal is contained.
• H/V FLIP
- Allows the displayed image to be ipped
horizontally or vertically.
- This feature provides exible mounting options
for camera operators.
- Activates in the order : [H Flip]-[V Flip]-[H/V Flip]-
[AUTO]
- In the [AUTO] mode, the vertical FLIP operates
automatically according to the position of the
unit.
• ZOOM
- Used to magnify the image up to 90% on a pixel
basis and display on full screen.
- ZOOM range is 10% to 90% by 10% increment.
* ex) 10% Zoom : If the input signal’s resolution is
1920 x 1080, only 90% (1728(H) x 972(V)) of the
image would be shown on full screen without
the remaining 10% (192(H) x 108(V)) of the image.
* See section “7. Other Functions [5] Zoom" for
more information.
• ZOOM SPLIT
- Used to magnify the image.
- Used to zoom the specied area sequentially.
- Designable areas are Left-Top, Right-Top, Left-
Bottom, Right-Bottom and Center.
• CCAPTION (Closed Caption)
- This function controls the Closed Caption.
- Available modes are ANC(608), LINE21(60.8),
ANC(708).
- Captions which meet the standard of '608 :
CEA-608-B' and '708 : CEA-708-C' are only
displayed on the screen.
• CC INFO (Closed Caption Infomation)
- Displays the Closed Caption information which
the monitor currently receives.
• CHANNEL (608)
- Sets the channel of Closed Caption 608.
- Available modes are CC 1 to CC 4.
• SERVICE (708)
- Sets the service of Closed Caption 708.
- Available modes are SERVICE 1 to SERVICE 6.

05 MENU OPERATIONS
19
4K/UHD Multi-Purpose Monitor
[4] DISPLAY / VIDEO
• FOCUS ASSIST
- Focus Assist helps the shooters to easily nd
out the exact area in the picture with good focus,
simply by adding colors on the shape or
boundaries of the object in the picture.
- Activates in order of [Mono On]-[Color On]-[O].
* [Color On] : Only the boudary of the area with
good focus is displayed with the designated
color.
* [Mono On] : The boundary of the area with good
focus is colored with the designated color, while
the rest of the areas(pixels) have only Y’(Luma)
signals to be black & white image.
* See section “7. Other Functions [7] Focus Assist”
for more information.
• FOCUS AS COLOR (Focus Assist Color)
- Used to select a color for Focus Assist among
RED, GREEN, BLUE, WHITE.
- This feature is available only when the Focus
Assist mode is activated.
• FOCUS AS LEVEL (Focus Assist Level)
- Used to set the edge dierence value between
the edges in an image.
- Available values are from 0 to 100. Larger the
value the more sophisticated the detail detection.
- Designated color is displayed when the dierence
of the edges exceeds the previously set value.
- This feature is available only when the FOCUS
ASSIST mode is activated.
• ARRI CAM STATUS (ARRI Camera Status)
- Used to display the camera status information
provided by ARRI ALEXA camera on the OSD.
- When the Arri Cam Status is activated, the
screen is squeezed to the 1742 x 980 resolution.
• LDS INFO (Lens Data System Information)
- Used to se set the information display of the Lens
Data System.
• INDEX LETTER
- Used to set the monitor identication character
notation in the upper right corner of the screen.
VIDEO이 LUM-095G
DSLR SEL
DSLR SCALE
TIMECODE
FOCUS ASSIST
FOCUS AS COLOR
FOCUS AS LEVEL
ARRI CAM STATUS
LDS INFO
INDEX LETTER
CANON 7D
O
OFF
OFF
RED
OFF
OFF
OFF
+ 90
PAGE (2/2)
• DSLR SEL
- Select the DSLR camera to be used with the
monitor. Available mode is [CANON 7D].
* DSLR cameras’ screen size and aspect ratio of
Live / Record / Playback modes vary depending
to their manufacturer.
• DSLR SCALE
- This is a special function for CANON/NIKON
DSLR cameras.
- Used to scale the image with the dierent
resolution as to the operation mode of the
camera to ll the screen fully.
- Available modes are LIVE/REC FULL, LIVE/REC
16:9, PLAYBAKC.
• TIMECODE
- Used to set the Time Code.
- Available modes are VITC (UP), VITC (DOWN),
LTC (UP), LTC (DOWN).

05 MENU OPERATIONS
20
4K/UHD Multi-Purpose Monitor
[5] WAVEFORM
OFF
OFF
OPAQUE
SAMLL
OFF
OFF
OFF
OFF
OFF
WAVEFORM LUM-095G
ENABLE
TYPE
INTENSITY
TRANS
SIZE
LINE WAVEOFORM
SEL LINE POS
LUMA CHECK
LUMA ADJUST
RANGE ERROR
Y MAX
Y MIN
C MAX
C MIN
Y PICTURE BLINK
C PICTURE BLINK
1
0
0
0
0
0
0
• ENABLE
- Used to activate/ deactivate the Waveform
which is selected in the Type menu.
• TYPE
- This function sets the Waveform and Vectorscope.
- Available options are dierent according to the
Input signal.
- Activates in the order: Waveform
- Vectorscope - Waveform Wide - Waveform YCbCr
- Waveform RGB - Wave Vector - YCbCr Vector
- Full Waveform - Full Vector - O.
• INTENSITY
- Used to set the brightness level of the Waveform/
Vectorscope display from 1 to 63.
- The higher the number the brighter the
waveform will be.
• TRANS (Transparency)
- Used to select the transparency option of the
Waveform/ Vectorscope between OPAQUE and
TRANS.
- Even though the option is set to [Opaque], it
will automatically turn to [Trans] when the
main OSD overlaps the waveform/vectorscope.
And turns back to [Opaque] when the main OSD
disappears.
• SIZE
- Adjust the size of the Waveform or Vectorscope.
- Available options are [SMALL] and [LARGE].
* See section “7. Other Function [2] Waveform /
Vectorscope“ for more information.
• LINE WAVEFORM
- This item is utilized to display one line data on
the Waveform.
• SEL LINE POS (Select Line Position)
- Used to select specic horizontal line for
Waveform / Vectorscope.
-Thisisavailable whenLINE Waveform isactivated.
- Use the Up and Down button to select a desired
vertical line.
- Control range varies according to the resolution
of the input SDI signal.
* PAL : Min. 1, Max. 625
* NTSC : Min. 1, Max. 525
* 720p : Min. 1, Max. 750
* 1080i : Min. 1, Max. 1125
* 1080p : Min. 1, Max. 1125
• LUMA CHECK
- Analyzes the Luma(Y’) level of the input image
and displays the selected zone on the screen.
- Available modes are [Color Pattern] and
[Zebra Pattern].
- After each pixel’s Y’ level is analyzed, it is
displayed as a certain color or zebra pattern
according to the Index on the right side of the
screen.
- When a pixel’s Y’ level is under 0%(16), the pixel
is displayed as green color or green diagonal
lines, and over 100%(235) as red color or red
diagonal lines.
- When the Y’ level of a pixel is between 0~100%,
the pixel is displayed as Gray level, except for
selected Luma Zone.
- In the [Color Pattern] mode, the zone the user
adjusted is displayed as Yellow (10% lower zone),
Pink (±2.5%), Cyan (10% upper zone).
- In the [Zebra Pattern] mode, ±5% of the selected
Y’Level will be displayed as diagonal lines.