TV One Voyager User manual

USB 2.0 Fiber Optic
KVM Extender System
User Guide
USB

Thank you for purchasing the
Voyager USB 2.0 Fiber Optic KVM extender
Please read this guide thoroughly.
This document applies to Part Numbers: 2350101-01 and 2350201-01.
Regulatory Agency Acceptance
We hereby certify that the Voyager USB 2.0 Fiber Optic KVM Extender to which this declaration relates
conforms to the protection requirements of the EMC Directive as determined by the following standards:
Applied and met EMC emission test standards:
Emission General Standard Referenced Standard
Radiated Emissions, Class B
EN 55022:2010/AC:2011
FCC CFR 47, Part 15
Subpart B
ICES-003 Issue 4
EN55022:2010/AC:2011
Conducted emissions, Class B EN55022:2010/AC:2011
Harmonic Current Emissions, Class A EN 61000-3-2:2006/
A2:2009
Flicker Emissions EN 61000-3-3:2008
Applied and met EMC immunity test standards:
Immunity General Standard Referenced Standard
Electrostatic discharge Immunity, Criterion B
EN 55024:2010
EN 61000-4-2:2009
Radiated RFImmunity, Criterion A EN 61000-4-3:2006/
A2:2010
EFT Immunity, Criterion B EN 61000-4-4:2004/
A1:2010
Surges Immunity, Criterion B EN 61000-4-5:2006
Conducted RFImmunity, Criterion A EN 61000-4-6:2009
Magnetic field Immunity EN 61000-4-8:2010
Voltage Dips & Interruptions Immunity,
Criterion B/C/C
EN 61000-4-11:1994
FCC Radio Frequency Interference Statement Warning
Class A Device: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide a reasonable
protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the Instruction Manual, may cause harmful interference to radio communications.
Caution: This equipment is intended for use in the manner prescribed in the Instruction Manual. Any
user changes or modifications not expressly approved by TV One Multimedia Solutions could void
the user’s authority to operate the equipment. The Instruction Manual shows or describes the proper
connection of this equipment for operation that insures FCC compliance

CE Statement
We declare under our sole responsibility that the USB 2.0 Voyager USB, to which this declaration
relates, is in conformity with European Standard EN 55022 Class B, EN 61000 and EN 55024.
IC Statement
This Class B digital apparatus complies with Canadian ICES-003.
©2014 All rights reserved. Products referred to herein are either the trademarks or the registered trademarks of tvONE. All other
trademarks are property of their respective owners. tvONE assumes no responsibility for errors that may appear in this manual.
Information contained herein is subject to change without notice.
Document # 90-01251-A01

Contents
Introduction ………………………………………………………………………………………………………………………… 3
Voyager USB 2.0 Fiber Optic KVM Extender Product Contents …………………………………… 3
Requirements……………………………………………………………………………………………………………………… 3
About the Voyager USB 2.0 Fiber Optic KVM Extender ………………………………………………… 3
CPU Transceiver Description …………………………………………………………………………………………… 4
REMOTE Transceiver Description ……………………………………………………………………………………… 5
Installation guide ………………………………………………………………………………………………………………… 6
Installing the CPU Transceiver…………………………………………………………………………………………… 6
Installing the REMOTE Transceiver …………………………………………………………………………………… 6
Connecting the CPU Transceiver to the REMOTE Transceiver ……………………………………… 7
Checking the Installation …………………………………………………………………………………………………… 7
Connecting a USB Device ………………………………………………………………………………………………… 8
Troubleshooting ………………………………………………………………………………………………………………… 8
Specifications ……………………………………………………………………………………………………………………… 11
Contacting Technical Support …………………………………………………………………………………………… 12
Technical Glossary …………………………………………………………………………………………………………… 13

Introduction
The instructions in this guide assume a general knowledge of computer installation procedures,
familiarity with cabling requirements, and some understanding of USB devices.
NOTE: Notes provide additional information that could be useful.
CAUTION: Cautions provide important information about an operational requirement.
Voyager USB 2.0 Fiber Optic KVM extender Product Contents
Voyager USB Kit is packaged with:
• CPU Transceiver
• REMOTE Transceiver
• AC Power Adapter
Regionally specific power cord
• 2x Multimode SFPs (singlemode available)
• Quick Start Guide
An additional AC power adapter may be purchased for the CPU Transceiver in the event that your USB port
cannot supply the required 500mA current.
Requirements
To complete the installation, you will also require the following items that are not included with the
product:
• USB 1.1 or 2.0 compatible computer (host computer) with a USB compliant operating system
• USB 1.1 or 2.0 compatible device(s)
• 2-strand fiber optic cable with Duplex LC connectors (if using surface cabling), or 2-strand
fiber optic cabling with two information outlets and two 2-strand fiber optic patch cords with
Duplex LC connectors (if using premise cabling)
The maximum length of the multimode fiber optic cable (MMF) supported by the Voyager USB system, including
patch cords is 500m over OM2 (or greater), or 275m over OM1. *Singlemode SFPs available for distances up to
10Km
About the Voyager USB 2.0 Fiber Optic KVM extender Product Contents
The Voyager USB 2.0 Fiber Optic KVM extender enables users to extend beyond the standard 5m
cable limit for USB peripheral devices. With the Voyager USB 2.0 Fiber Optic KVM extender, USB
devices can be located up to 500 meters from the computer. The Voyager USB 2.0 Fiber Optic KVM
extender is composed of two individual units: the CPU Transceiver and the REMOTE Transceiver.
note
note
note
3
The Voyager USB 2.0 Fiber Optic KVM extender includes the Voyager USB suite of features:
• Transparent USB extension
• True plug and play; no software drivers required
• Works with all major operating systems: Windows®, Mac OS X®, and Linux®
USB