TVS electronics BS-i201G User manual

8. Buzzer Pitch
Buzzer pitch code, Modify the Tone of beep sounded
by the Scanner when reading well, Default=medium
(8410061600)
Low (1600 Hz)
(8410062400)
Medium(2400 Hz)
(8410064200)
High(4200 Hz)
9. Version
Show version
Barcode
Scanner
BS-i201G/BS-i203G
Barcode Scanner-
Quick Reference Guide
Barcode Scanner- Quick Reference Guide
E Waste Management Instructions:
Do's and Dont's
Do's:
Always drop your used electronic products &
Accessories/Consumables /spares/ batteries
and packaging materials after the end of their
life at the nearest collection point.
Separate the packaging material according to
responsible waste disposal options and sorting
for recycling.
Keep the product in isolated area, after it
becomes non-functional/un-repairable so as to
prevent its accidental breakage
Dont's:
The product is not meant for re-sale of any
unauthorized agencies/scrap dealers
Never dump e-waste in garbage bins
Do not dispose off your product in at municipal
waste bins
Do not throw used batteries into household
waste.
Waste Collection:
TVS-E has put in place a pan India collection
mechanism to assist its customers in depositing
their e-waste as per the new E-waste
(Management) Rules, 2016 effective from 1st
October, 2016.
You can deposit the WEEE at the nearest
Collection Point. Details of the location of
Collection Points and Collection Centres
information are also available on this website.
TVS-E assures all its customers that all its
e-waste collected under these Rules will be
recycled/ disposed of by an authorized e-waste
Recycler as per the E-waste Management
Rules, 2016.

BS-i201G/BS-i203G Quick Reference Guide
1、Open the package and check the appearance and
accessories
2、Getting started
Before connecting the scanner, please don’t turn on the
computer until the scanner is fully connected.
3、Connecting and transmitting schemes
3.1 USB connection
Connecting the computer and scanning "USB Keyboard"
barcode, you can configure the device for USB keyboard
mode. When the application software need the serial com
input, the USB device could be configured as "USB COM"
type. User need to install the USB COM driver. (The default
configuration of this barcode is 115200 baud rate, 8 data bits,
no parity, 1 stop bit).
USB Keyboard
USB COM
3.2 RS232 connection
The "RS232" barcode is used when connecting to the
serial port of a PC or terminal. The following "RS232" barcode
also programs a carriage return(CR) and a line feed(LF) suffix.
The serial configuration is: 115200 baud rate, 8 data, no parity,
1 stop bit.
RS232
4、Active Factory Defaults
Scanning the "Active Factory Defaults" barcode
below will default the device to its factory condition.
Active Factory Defaults
5、Function configuration
5.1 Configure carriage return(CR),line feed(LF)
Add CR suffix
Add CR suffix and LF suffix
Clear CR suffix and LF suffix
5.2 Scan mode
The default mode is Manual trigger mode, please scan
the configuration code to auto scanning mode.
Auto scanning mode
Manual trigger mode
6、Troubleshooting
6.1 Power failure
First check the host device whether it is properly powered;
Secondly check the USB cable whether it connect properly.
6.2 Scan once, no light and no scanning
Firstly, check if the device connection is stable (the blue
colored light always on). Secondly, check if the USB COM
barcode has been scanned mistakenly (no transmission). If
scanned mistakenly, please power cycle and scan the USB
Keyboard barcode.
6.3 Transmission failure
S1 Connection check: Please make sure the connection
between the scanner and the terminal is successful. If
successfully, the power-on tone will be heard.
S2 Transmission check: Please scan the sample code
below. If the sample code is transmitted, please go to S3. If the
sample code is not transmitted but there is a decoding tone,
go to S4. If the sample code is not transmitted and there is no
decoding tone, please contact technical support.
S3 Barcode check: Please rescan the same type of
barcode without defacement. If transmitted, it’s due to
defacement. If not please contact technical supporter.
S4 Transfer software check: Please open the text file and
serial port transmission tools. If there is output in one of these
tools, please refer to the 3.1 USB connection section in this
manual for the configuration of what you need. If there is no
output, please contact technical supporter.
12345
7、Technical supporting
If this manual doesn’t solve your problem, please contact
your supplier.
Clear CR suffix