TVS electronics BS-i203G BT User manual

BS-i203G BT / BS-i203G+BT
1.Open the package and check the appearance
and accessories
2. Please press the button to turn the scanner on
3. Connecting and transmitting schemes
Attention please: The default connection mode of the scanner
is 2.4G, which can be configured into Bluetooth mode as needed.
After booting, it will try to connect according to the connection
method before shut down. For example, before the scanner turns
off, the scanner and the mobile phone Bluetooth pair successfully.
After rebooting, the scanner will automatically connect to the
mobile phone while the mobile phone has not ignored the scanner
and its Bluetooth on.
Scanner function setting step:
3.1 Bluetooth mode
Turn on the Bluetooth of terminal devices and use the scanner
scans“EnterSettings”-“BluetoothHID Mode”-“Searching”-“Exit
Settings” in sequence. Find and choose the “Barcode Scanner
HID” on the terminal device to connect. If successfully, the blue
colored indicator will be on. (Note: For the meaning of indicator
refer to part 8).
①Enter Settings
②Bluetooth HID Mode
③Searching
④Exit Settings
3.2 2.4G mode
After plugging Dongle into the computer and the computer
identifying Dongle successfully, pls. scan “Enter Settings”-“2.4G
Mode”-“Connect Dongle”-“Exit Settings” in sequence to pair.
After connect successfully, the blue colored lights will be on.
(Note: For the meaning of indicator refer to part 7).
①Enter settings
②2.4G Mode
③Connect Dongle
④Exit Settings
4. Active Factory Defaults
Scanning the “Active Factory Defaults” barcode below will
return the scanner to its factory configuration. This barcode does
not change the connection and transmission method.
Active Factory Defaults
5. Function configuration
5.1 Configure carriage return (CR),line feed (LF)
Scan “Enter Settings” to start functional setting. To scan one
of the functional barcode below as you needed, then need to scan
“Exit Settings” to complete the functional setting.
Enter settings
Add CR suffix
Add LF suffix
Add CR+LF suffix
Clear CR+LF suffix
Exit Settings
6. Power down method
When you do not use the scanner device, you can scan the
following barcodes in sequence to shut down the scanning device
directly.
①Enter Settings
Enter Settings
Reading function barcode
Exit Settings

②Power Down
7. Operating Modes
The barcode scanner has two operating modes: normal
mode and inventory mode, through a different set code to
operate the mode switch
Normal mode, the scanning data directly through the
cable or wireless transmission to the computer, after the
success of the scanning, it will issue a low frequency short
tone. If the transmission fails, issue a 3-channel
low-frequency tone to alert. In normal mode, if the
transmission fails, the sweep of the bar code will be lost.
Normal Mode
If the barcode scanner works beyond 2.4G or Bluetooth
transmission range, it is recommended to use storage mode.
WireleaIf the internal storage is full, the scanner will send three low
frequency short tone alarm.
Inventory Mode
Scan the number of bar codes stored in the storage area by
scanning the "Total unmber of Storage" barcode:
Total number of Storage
Upload the stored data by scanning the "Data Upload"
barcode. After the data is uploaded, the barcode stored in the
barcode scanner is not automatically deleted. The user
uploads the storage data multiple times by scanning the "data
upload".
Data upload
Note: When data upload, please try to ensure that the wireless
signal connection is good, or in the connection of data line.
Clear data
By scanning the "clear data" bar code to clear the storage area
of the bar code data, bar code will not be able to upload after
the clear, please confirm whether the data has been uploaded
8. Meaning of indicator status &beeper tone
The blue colored light and the green colored light flash
alternately: The scanner under Bluetooth searching.
The green colored light single flashes: The scanners try to
pair with the Dongle through 2.4G mode.
The blue colored light always on: The scanner under
connection. The light will turn off after disconnect.
The two green colored lights flash one after one: The scanner
under connection. Decoding and transmitting are successful.
One green light colored flashes while the other one flashes
two times: The scanner disconnected, the decoding is successful
but transmitting fails.
Beep three times: The device receives message abnormally
from Scanner.
Beep twice: Disconnected.
Beep once: Good connection. Scanner power on. Good
transmission.
Beep always: Low battery Alert. Shut down and charge
ASAP.
The red colored light always on: The scanner is charging, and
light will off after charging completion.
9. Common Questions
9.1 What to do if can not connect to Bluetooth?
Make sure the phone is android 3.0 or above, go to 3.1
Bluetooth Mode setting and scan functional barcodes in sequence,
open the mobile phone Bluetooth, search for a new device, and
click “Barcode Scanner HID” to connect.
9.2 Why part of the barcodes can not scan?
Because some uncommon barcode types are turned off by
default, you can scan functional barcode to open the dedicate
barcode types. If you do not know the functional barcode, please
contact your supplier.
9.3 Why barcodes can not be uploaded to a computer

or phone?
S1 Make sure the scanner turns on and works normally.
S2 Determine whether the scanner and the terminal device are
under good connection. The blue colored light on scanner is off pls.
go to S3. It is on pls. go to S4.
S3 The scanner and the terminal device do not connect
successfully, please go to 3.1 Bluetooth Mode setting or 3.2 2.4G
Mode setting. Confirm good connection and then scan the barcode
to transmit.
S4 Please check if there is other terminal device in the
communication range. If the scanner connects to other terminal
device, please disconnect and go to 3.1 or 3.2 to connect with this
terminal device.
9.4 How to do if computer or mobile phone cannot
find the Bluetooth scanner?
First pls. check if the Bluetooth of the terminal device works
normally. If yes, pls. go to 3.1 Bluetooth Mode setting.
9.5 Bluetooth scanner has been connected with the
phone or computer through Bluetooth before, how to
pair with the phone or computer again?
If the scanner does not connect with other devices after
disconnecting with this terminal device, the scanner will connect
with the terminal device automatically while both of them turn on.
If the scanner has connected with other devices, or the automatic
connection with this device fails, pls. delete the paired Bluetooth
(“Barcode Scanner HID”)on the terminal device and go to 3.1
Bluetooth Mode setting.
9.6 The Bluetooth of the scanner connects with
device-A first, then connects with device-B, and then
disconnects with device-B, will it connect with
device-A automatically?
It will not connect with device-A automatically. You need
delete the paired Bluetooth (“Barcode Scanner HID”) on the A
device and go to 3.1 Bluetooth Mode setting.
9.7 The scanner connects to the terminal device, how
to connect with another terminal device?
9.8 Will it reconnects automatically after turning it
off?
2.4G mode: When Dongle connects to the terminal device
and the scanner has not established a new connection with other
terminal devices, the scanner will connect automatically after
re-power on.
Bluetooth mode: The terminal device establishes a
connection through Bluetooth Mode before the scanner turns off.
After shutting down, there is no deletion on the Bluetooth list of
the terminal device, the scanner will connect automatically after
re-power on.
If the connection is not successful, go to 3.1 or 3.2.
9.9 Why Red light does not shine when charging?
Please confirm the power supply device turns on, let the
scanner power off and charge again.
10. Technical supporting
If this manual doesn’t solve your problem, please contact
your supplier.
E Waste Management
Instructions: Do's and Dont's
Do’s
Always drop your used electronic products & Accessories/Consumables
/spares/ batteries and packaging materials after the end of their life at the
nearest collection point.
Separate the packaging material according to responsible waste disposal
options and sorting for recycling.
Keep the product in isolated area, after it becomes non-functional
un-repairable so as to prevent its accidental breakage
Dont's
The product is not meant for re-sale of any unauthorized agencies/scrap
dealers
Never dump e-waste in garbage bins
Do not dispose off your product in at municipal waste bins
Do not throw used batteries into household waste.
Waste Collection
TVS-E has put in place a pan India collection mechanism to assist its
customers in depositing their e-waste as per the new E-waste (Management)
Rules, 2016 effective from 1st October, 2016.
You can deposit the WEEE at the nearest Collection Point. Details of the
location of Collection Points and Collection Centres information are also
available on this website.
You can dispose of a used TVS-E product very easily and responsibly.
Simply call at 1800425 4528 and drop it at your nearest Collection points .
All these E-waste will be consolidated and forwarded to Tumkur Collection
point for final disposal through Authorized E-waste Recycler
TVS-E assures all its customers that all its e-waste collected under these
Rules will be recycled/ disposed of by an authorized e-waste Recycler as
per the E-waste Management Rules, 2016.
TVS-E Commitment:
TVS-E is committed to environmentally sound management of e-waste
taking all steps required to ensure that e- waste are managed in a manner
which shall protect health and environment against any adverse effects
which may result from hazardous substance contained in such wastes.
TVS-E assures that the covered products do not contain lead, mercury,
cadmium, hexavalent chromium, poly- brominated biphenyls or
poly-brominated di-phenyl ethers above a specified threshold. The
threshold for cadmium is 0.01% by weight in homoge- neous material, for
all other substances, the threshold is 0.1% by weigh t in homogeneous
material.
Connect A in 2.4G mode
Pull the dongle out of A
Scan required barcode
Plug dongle into B or
open B’s Bluetooth
connect B
connect A in Bluetooth mode
Close A’s Bluetooth