Twin-Star International Chimney Free DFI020ARU User manual

ATTENTION
IF YOU HAVE ANY PROBLEMS OR QUESTIONS, EMAIL
OR CALL CUSTOMER SERVICE BEFORE YOU RETURN
THIS PRODUCT TO THE STORE WHERE IT WAS PURCHASED.
For Customer Service: email: par[email protected]
in English Call: 800-318-9373
in Spanish Call: 800-318-9373
in French Call: 800-318-9374
ATENCIÓN
SI TIENE ALGÚN PROBLEMA O PREGUNTAS,
ENVÍE UN MENSAJE DE CORREO ELECTRÓNICO O LLAME AL SERVICIO
DE ATENCIÓN AL CLIENTE ANTES DE DEVOLVER
ESTE PRODUCTO A LA TIENDA EN LA QUE LO COMPRÓ.
Servicio de atención al cliente: Correo electrónico: par[email protected]
Línea para llamadas en inglés: 800-318-9373
Línea para llamadas en español: 800-318-9373
Línea para llamadas en francés: 800-318-9374
STOP STOP
PARE PARE
ATTENTION
SI VOUS AVEZ DES PROBLÈMES OU DES QUESTIONS,
ENVOYEZ UN COURRIEL AU SERVICE À LA CLIENTÈLE OU APPELEZ LE
SERVICE À LA CLIENTÈLE AVANT DE RETOURNER
CE PRODUIT OÙ VOUS L’AVEZ ACHETÉ.
Pour le service à la clientèle : courriel : par[email protected]
pour le service en anglais, appelez au: 800-318-9373
pour le service en espagnol, appelez au: 800-318-9373
pour le service en français, appelez au: 800-318-9374
ARRÊT ARRÊT
INSTRUCTION MANUAL ENCLOSED
MANUEL D’INSTRUCTION À L’INTÉRIEUR
MANUAL DE INSTRUCCIONES ADJUNTO
INSTRUCTION MANUAL ENCLOSED
MANUEL D’INSTRUCTION À L’INTÉRIEUR
MANUAL DE INSTRUCCIONES ADJUNTO
Meijer.com

CONSUMER SAFETY INFORMATION
PLEASE READ THIS MANUAL BEFORE USING THIS APPLIANCE.
WARNING!!
IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED
EXACTLY, AN ELECTRIC SHOCK OR FIRE MAY RESULT CAUSING
PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS
AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.
FIREPL A C E INSE R T
HOMEOWNERS OPERATING MANUAL
MODELS:DFI016ARA, DFI016ARU
V E N T FRE E F I REPL A C E WIT H H E A T E R
Thank you and congratulations on your purchase of a Twin-Star International, Inc.
(Twin-Star) fireplace. Please read the Operating Instructions before using this appliance.
IMPORTANT: Read all instructions and warnings carefully before using this appliance.
Failure to follow these instructions may result in a possible electric shock, fire hazard
and/or injury and will void the warranty.
E-1
ELEC T R I C F IRE P L A C E
Made in China
Printed in China
ALSO Requires-
Wood Fireplace Mantel
ATTENTION
E-mail: [e-mail]
In English Call: 800-318-9373
In French Call: 800-318-9374
In Spanish Call: 800-318-9373
For Customer Service:
DFI020ARA, DFI020ARU
WARNING: THIS IS AN UNVENTED,
ELECTRIC APPLIANCE. DO NOT
ATTEMPT TO BURN WOOD OR
MANUFACTURED FIRELOGS IN OR
ON THIS APPLIANCE OR GRATE.
Distributed by Twin-Star International, Inc.
Under license. duraameTM and the
duraame ame logo are trademarks
of Duraame, Inc.
Twin-Star International, Inc.
Delray Beach, FL 33445
Made in China • Printed in China
Meijer.com

SAVE THESE
INSTRUCTIONS
E-2
1. Read all instructions before using this appliance.
2. This appliance is hot when in use. To avoid burns,
do not let bare skin touch hot surfaces. If provided,
use handles when moving this appliance. Keep
combustible materials, such as furniture, pillows,
bedding, papers, clothes and curtains at least 3 feet
(0.9 m) from the front of this appliance.
WARNING: In order to avoid overheating, do not
cover the heater. It can not be used in a wardrobe.
3. CAUTION: Whenever the heater is left operating
and unattended, extreme caution is necessary if
children or invalids are nearby.
4. The appliance is not to be used by children or
persons with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or
instruction.
5. Children should be supervised and not allowed to
play with the appliance.
6. If possible, always unplug this appliance when
not in use.
7. Do not operate any heater with a damaged cord or
plug or after the appliance malfunctions, or if it has
been dropped or damaged in any manner.
8. If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
9. Any repairs to this fireplace should be carried out
by a qualified service person.
10. Under no circumstance should this fireplace
be modified. Parts having to be removed for
servicing must be replaced prior to operating this
fireplace again.
11. Do not use outdoors.
12. This heater is not intended for use in bathrooms,
laundry areas and similar indoor locations. Never
locate this appliance where it may fall into a
bathtub or other water container.
13. Do not run cord under carpeting. Do not cover
cord with throw rugs, runners or the like. Arrange
cord away from traffic areas and where it will not
be tripped over.
14. To disconnect this appliance, turn controls to the
off position, then remove plug from outlet.
15. Connect to properly grounded outlets only.
16. This appliance, when installed, must be electrically
grounded in accordance with local codes or, in the
absence of local codes, with the current CSA C22.1
Canadian Electrical Code or for U.S.A. installations,
follow local codes and the National Electrical
Code, ANSI/NFPA NO.70.
17. There is a thermostat limiter inside the heater.
When the inner temperature over-heats or abnormal
heating occurs, the thermostat protective device will
cut-off the power supply to avoid damage to the
fireplace or risk of fire.
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire,
electrical shock, and injury to persons including the following:
18. The heaters must not be located immediately
below a socket-outlet.
19. Do not insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause an
electric shock or fire, or damage the appliance.
20. To prevent a possible fire, do not block air intakes
or exhaust in any manner. Do not use on soft
surfaces, like a bed, where opening may become
blocked.
21. This appliance has hot and arcing or sparking parts
inside. Do not use it in areas where gasoline, paint
or flammable liquids are used or stored. This
fireplace should not be used as a drying rack for
clothing. Christmas stockings or decorations should
not be hung in the area of it.
22. Use this appliance only as described in the
manual. Any other use not recommended by the
manufacturer may cause fire, electric shock or
injury to persons.
23. Avoid the use of an extension cord because the
extension cord may overheat and cause risk of
fire. However, if you have to use an extension
cord, the cord must be No.14 AWG minimum size
and rated not less than 1875 Watts. The extension
cord must be a three wire cord with grounding type
plug and cord connection. The extension cord shall
not be more than 20 feet (6 m) in length.
24. See directions in Figure 1.
This heater is for use with 120 Volt outlet. The cord has
a plug as shown in Figure 1. See Figure 1 for grounding
instructions. An adapter as shown at C is available for
connecting three-blade grounding type plugs to two-slot
receptacles. The green grounding plug extending from
the adapter must be connected to a permanent ground
such as a properly grounded outlet box. The adapter
should not be used if a three-slot grounded receptacle
is available.
Figure 1
GROUNDING PIN
METAL SCREW
COVER OF GROUNDED
OUTLET BOX
B
A
C
GROUNDING PIN
D
ADAPTER
GROUNDING
MEANS
IMPORTANT INSTRUCTIONS
Meijer.com

E-3
Logs & Emberbed
Heater/Blower Assembly
Thermostat
Control Panel Circuit Board
Main Control Circuit Board
Flame Generator Drive Motor
Flame Generator/Spinner
Remote Control - 4 Buttons
PARTS LIST
DFI016ARU
Part Name
Main Power Switch
Knob for Heater Temperature control
Fig, 2
PORDUCT ORIENTATION
Flame Circuit Board
Logs And Emberbed
Faceplate
Heater / Blower
Assembly
Power Cord And Plug
Control Panel
DFI020ARU
DFI016ARA DFI020ARA
Meijer.com

1. No power, the power switch is in“”ON position. 1. Check that the unit is plugged into a standard
120V outlet.
3b. Make sure that the TEMPERATURE knob is set to
the max setting.
2. Logs Glow, flame effect does not work.
3. Flame effect operates, but heater does not
blow warm air.
4. Unit heater does not work.
2. Check whether Flame Generator drive motor is
running . If not call the customer service.
4. Turn all switches to the
“”OFF position and unplug
the unit from the wall outlet for 5 minutes. After 5
minutes, plug the unit back into the wall outlet and
operatate as normal.
3a. Try to trun ON/OFF HEATER button several times
to make sure it is in ON position.
FIREPLACE LOCATION
When choosing a location for your new fireplace,
ensure that the general instructions are followed.
Also, for best effect, install the fireplace out of
direct sunlight.
Cold climate installation recommendation:
when installing this unit against a
non-insulated exterior wall or chase, it is
mandatory that the outer walls be insulated
to conform to applicable insulation codes.
ELECTRICAL CONNECTION
A 15 AMP, 120 Volt, 60 Hz circuit with a
properly grounded outlet is required. Preferably, the
fireplace will be on a dedicated circuit as other
appliances on the same circuit may cause the circuit
breaker to trip or the fuse to blow when the heater is
in operation. The unit comes standard with 6 feet
(1.8 m) three wire cord, exiting from the rear of the
fireplace. Plan the installation to avoid the use of
an extension cord. If an extension cord must be
used, it must be a minimum 14 AWG ; three wires
with grounding type plug connector and rated
not less than 1875 Watts. The cord shall not be
more than 20 feet (6 m) in length.
ELECTRICAL SPECIFICATIONS
Voltage: 120VAC, 60Hz
Amps: 11.7 Amps
Watts: 1400 Watts
CLEARANCE TO COMBUSTIBLES
Keep electrical cords, drapery, furniture and other
combustibles at least 3 feet (0.9 m) from the front of the
heater and away from the sides.
CLEANING TRIM
Clean the metal trim using a soft cloth, slightly
dampened with citrus oil based product and buff with
a clean soft cloth. DO NOT use brass polish or
household cleaners as these products will damage
the metal trim. Citrus oil based products can be
obtained at supermarkets or hardware stores.
TROUBLE SHOOTING GUIDE
PROBLEM SOLUTION
E-4
Meijer.com

OPERATING INSTRUCTIONS CONTROL FUNCTIONS
POWER
HEAT
TEMPERATURE
FLAME
5
Fig. 3
Models: DFI016ARA/DFI016ARU/DFI020ARA/DFI020ARU
The POWER switch supplies power to all of the
function of the fireplace. This switch must be in
“ ” position for any functions including the
remote to work.
Each time the FLAME button is pressed, the
intensity of the flame decreases. There are six
brightness levels you can cycle through including
the “ ” OFF setting.
The HEAT button will turn ON/ OFF he heat out-
put. When the heater is turned on it will take
several seconds for the unit to begin blowing
hot air. The heat indicator was installed in log set.
When the unit was ON the log set will be light up
to indicate the unit was on.
The TEMPERATURE control knob regulates the tem-
perature level of the heater. The further the knob is
rotated clockwise, the higher the set point temperature.
Turning the knob counter-clock-wise will lower the set
point temperature. Use this function to help regulate
the ambient temperature level.
WARNING: During any service of this appliance,
the power to the unit must be turned off. First turn
the main power switch to the “ ” OFF position.
Then remove the electrical plug from the wall outlet.
Meijer.com

Fig. 4
REMOTE CONTROL FUNCTIONS
E-6
4 BUTTONS REMOTE
POWER
The Power button will put the insert in a standby mode.
This will turn off all functions at once but will hold the
settings in memory. By pressing the button again the unit
will turn on at the same settings.
HEAT
This button will turn the power to the heater and
blower on and off. when the heater is turned ON it
will take several seconds for the unit to begin blowing
hot air. The rotary switch (Temperature) controls the
thermostat feature to help regulate your room’s
temperature accordingly.
FLAME
Each time this button is pressed, the intensity of the
flame decreases. There are six brightness levels you
can cycle through including the OFF setting.
NOTE: The unit Main Power Switch must be turn on
in order for the Remote Control to function.
Notice: This remote control uses 2 PCS AAA batteries. Never dispose of
batteries in fire, except under condition
controlled incineration. (Failure to observe this precaution may result in an explosion.)
MAINTENANCE
The motors used on the fan and the flame generator assembly are pre-lubricated for extended bearing life and
require no further lubrication. However, periodic cleaning/vacuuming of the fan/heater unit is recommended.
Make sure the unit is turned OFF and unplugged whenever you are cleaning the heater or fireplace.
WARNING: Make sure the power is turned off before proceeding. Any electrical repairs or
rewiring of this unit should be carried out by a licensed electrician in accordance with
national and local codes.
If repairing or replacing any electrical component or wiring, the original wire routing, color
coding and securing locations must be followed.
WARNING: Electrical outlet wiring must comply with local building codes and other applicable
regulations to reduce the risk of fire, electrical shock and injury to persons.
WARNING: Do not use this fireplace if any part of it has been under water. Immediately call a
qualified service technician to inspect the fireplace and replace any part of the electrical system.
Warning: Disconnect power before attempting any maintenance or cleaning to reduce the risk
of fire, electrical shock or personal injury.
MAINTENANCE
Warning: During any service of this appliance, the power to the unit must be turned off.
First turn the main power switch to the “OFF” position. Then remove the electrical plug from
the wall outlet.
PLAY/PAUSE
Press this button you can control the undulating flame
effect to play or pause.
Note:This button function just apply for ARU series
model.
Note: Please operate remote transmitter at a slow measured
pace. Depress the remote control buttons with an even motion
and gentle pressure. Repeatedly pressing buttons in rapid
succesion may cause the transmitter to malfunction.
Meijer.com

BASIC WARRANTY
IF WARRANTY SERVICE IS NEEDED
1 YEAR LIMITED WARRANTY
Twin-Star ™ Electric Fireplace Models
Twin-Star International, Inc.
Delray Beach, FL 33445
Made in China
Printed in China
© 2009, Twin-Star International, Inc.
E-7
Twin-Star International, Inc. (hereinafter referred to
collectively as the (“Company”) warrants that your
new Twin-Star Electric Fireplace is free from
manufacturing and material defects for a period of
one year from date of purchase, subject to the
following conditions and limitations.
1. This electric fireplace must be installed and
operated at all times in accordance with the
installation and operating instructions furnished
with the product. Any unauthorized repair, alteration,
willful abuse, accident, or misuse of the product
shall nullify this warranty.
2. This warranty is non-transferable, and is made to
the original owner, provided that the purchase was
made through an authorized supplier of the company.
3. The warranty is limited to the repair or replacement
of part(s) found to be defective in material or
workmanship, provided that such part(s) have been
subjected to normal conditions of use and service,
after said defect is confirmed by the Company’s
inspection.
4. The Company may, at its discretion, fully discharge
all obligations with respect to this warranty by
refunding the wholesale price of the defective part(s).
5. Any installation, labor, construction, transportation,
or other related costs/expenses arising from defective
part(s), repair, replacement, or otherwise of same,
will not be covered by this warranty, nor shall the
Company assume responsibility for same.
6. The owner/user assumes all other risks, if any,
including the risk of any direct, indirect or
consequential loss or damage arising out of the
use, or inability to use the product, except as
provided by law.
7. All other warranties – expressed of implied –
with respect to the product, its components and
accessories, or any obligations/liabilities on the
part of the Company are hereby expressly excluded.
8. The Company neither assumes, nor authorizes any
third party to assume, on its behalf, any other
liabilities with respect to the sale of the Twin-Star
product.
9. The warranties as outlined within this document
do not apply to non Twin-Star accessories used in
conjunction with the installation of this product.
This warranty is void if:
a. The fireplace is subjected to prolonged periods of
dampness or condensation.
b. Any unauthorized alteration, willful abuse,
accident, or misuse of the product.
c. You do not have the original receipt of purchase.
For update and revisions to this manual
please see our website
www.twinstarhome.com/instructions
U.S.A.
Contact the company, at [email protected],
or call 800-318-9373 in English, 800-318-9374 in
French, 800-318-9373 in Spanish.Make sure you have
your warranty, your sales receipt, location of purchase
and the model/serialnumber of your Twin-Star products.
For Customer Service:
E-mail: [e-mail]
In English Call: 800-318-9373
In French Call: 800-318-9374
In Spanish Call: 800-318-9373
10. This warranty gives you specific legal rights, and
you may also have other rights which vary from
state to state.
Meijer.com