TWINKLE TF-102 User manual

Digital Wireless Microphone
Date: 2011-03-11
REV.:
TF
-
10
2
User Manual
Product Name：Digital Wireless Microphone
Model No：TF-102
Company Name：TWINKLE

Digital Wireless Microphone
Date: 2011-03-11
REV.:
TF
-
10
2
MIC I / O Port
MIC RX
MIC TX
Audio In
Blue LED
Power On / Off
Pairing key
Green LED
Power On / Off
Pairing key
3V Battery
9V 0.65A Adapter
Audio Out Jack
6Φ
3.5Φ

Digital Wireless Microphone
Date: 2011-03-11
REV.:
TF
-
10
2
Setup Guide
1. Put AA battery 1.5V 2 pcs in the MIC as Graph1 and close the battery cover.
2. Press the blue bottom on MIC to turn on power as Graph 2 and then the green LED will flash
slowly.
3. Connect audio out jack on the receiver to the stereo amplifier.
4. Connect power supply to power jack on the receiver. Press the blue bottom on the receiver as
Graph 3 and then the blue LED light will flash slowly.
5. First press the blue bottom on the MIC for two seconds and then do the same procedure on
the receiver to pair MIC and the receiver. The LED lights will flash quickly while pairing
process.
6. When the LED lights on MIC and the receiver are on, the pairing process is successful.
7. Just enjoy wireless MIC set after successful pairing.
(Graph 1) (Graph 2) (Graph 3)

2.4G Digital Wireless Microphone
Date: 2011-01-11
REV.:
Specification
Wireless Microphone Transmitter
2400 ~ 2483.5 MHz
Operation Frequency Range
2.4GHz ISM Band Hopping mode
ID code setting Auto Pairing by Tack Switch
Modulation Type GFSK
RF Output power 6dBm (typ.)
RF Sensitivity - 80 dBm (min.)
Supply Voltage 3V (1.5 V AAA Battery X 2 PCS)
Supply Current 70mA (max.)
Power ON / OFF By Tack Switch
Transmission range 30m (min.)
Operation Temperature 0 ℃~ + 50 ℃
Dimension 144mm x 25.4mm x1.0mm
Wireless Microphone Receiver
2400 ~ 2483.5 MHzOperation Frequency Range
2.4GHz ISM Band Hopping mode
ID code setting Auto Pairing by Tack Switch
Demodulation Type GFSK
RF Sensitivity - 80 dBm (min.)
RF Output power 6dBm (typ.)
Audio Frequency Response 20 Hz ~ 15 KHz
Audio Output Level 560mV (typ.) @ 400mV Audio Input
Supply Voltage 9V DC
Supply Current 80mA (max.)
Power ON / OFF By Tack Switch
Audio Output Connector 3.5Φ & 6
Φ
Operation Temperature 0 ℃~ + 50 ℃
Dimension 50mm x 53mm x1.0mm

2.4G Digital Wireless Microphone
Date: 2011-01-11
REV.:
Mapping Table
Search for 28CH Frequency(MHz) Search for 28CH Frequency(MHz)
CH0 2408 CH14 2450.5
CH1 2425.5 CH15 2468
CH2 2443 CH16 2418
CH3 2460.5 CH17 2435.5
CH4 2410.5 CH18 2453
CH5 2428 CH19 2470.5
CH6 2445.5 CH20 2420.5
CH7 2463 CH21 2438
CH8 2413 CH22 2455.5
CH9 2430.5 CH23 2473
CH10 2448 CH24 2423
CH11 2465.5 CH25 2440.5
CH12 2415.5 CH26 2458
CH13 2433 CH27 2475.5

Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
For Wireless Microphone Transmitter:
The equipment complies with FCC RF exposure limits set forth for an uncontrolled environment. The
equipment must not be co-located or operating in conjunction with any other antenna or transmitter.
For Wireless Microphone Receiver:
This equipment must be installed and operated in accordance with provided instructions and the antenna(s)
used for this transmitter must be installed to provide a separation distance of at least 20 cm from all
persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
End-users and installers must be provide with antenna installation instructions and transmitter operating
conditions for satisfying RF exposure compliance.