TYAN Toledo i3210W User manual

1
http://www.tyan.com
Toledo i3210W
Toledo i3200R /// S5211 S5211-1U
Version 1.4
Copyright
Copyright © 2009 MiTAC International Corporation. All rights reserved. TYAN®is a
registered trademark of MiTAC International Corporation.
Trademark
All registered and unregistered trademarks and company names contained in this
manual are property of their respective owners including, but not limited to the
following.
TYAN®, Toledo i3210W, Toledo i3200R are trademarks of MiTAC International
Corporation.
Intel®, Quad-Core Intel®Xeon®processor 3300 and 3200 series, Dual-Core Intel®
Xeon®processor 3100 and 3000 series, Intel®CoreTM2 Extreme / Quad processor
Q6000 sequence / Duo processor E6000 sequence, and combinations thereof are
trademarks of Intel Corporation.
Phoenix, Phoenix-AwardBIOS are trademarks of Phoenix Technologies.
Microsoft, Windows are trademarks of Microsoft Corporation.
SuSE,is a trademark of Novell.
IBM, PC, AT, and PS/2 are trademarks of IBM Corporation.
Notice
Information contained in this document is furnished by MiTAC International
Corporation and has been reviewed for accuracy and reliability prior to printing.
MiTAC assumes no liability whatsoever, and disclaims any express or implied
warranty, relating to sale and/or use of MiTAC products including liability or
warranties relating to fitness for a particular purpose or merchantability. MiTAC
retains the right to make changes to product descriptions and/or specifications at
any time, without notice. In no event will MiTAC be held liable for any direct or
indirect, incidental or consequential damage, loss of use, loss of data or other
malady resulting from errors or inaccuracies of information contained in this
document.

2
http://www.tyan.com
Table of Contents
Check the box contents! 3
Chapter 1: Introduction
1.1 Congratulations 5
1.2 Hardware Specifications 5
Chapter 2: Board Installation
2.1 Board Image 8
2.2 Block Diagram 10
2.3 Board Parts, Jumpers and Connectors 12
2.4 Tips on Installing Motherboard in Chassis 20
2.5 Installing the Memory 21
2.6 Installing the Processor and Cooling Fan 24
2.7 Attaching Drive Cables 27
2.8 Installing Add-in Cards 28
2.9 Installing Optional SO-DIMM Modules 29
2.10 Connecting External Devices 30
2.11 Installing the Power Supply 31
2.12 Finishing Up 31
Chapter 3: BIOS Setup
3.1 About the BIOS 33
3.2 Main BIOS Setup 35
3.3 Main Menu 36
3.4 Advanced Menu 43
3.5 Security Menu 62
3.6 Power Menu 63
3.7 Boot Menu 64
3.8 Exit Menu 65
Chapter 4: Diagnostics
4.1 Beep Codes 67
4.2 Flash Utility 67
4.3 Phoenix BIOS Post Code 68
Appendix: SMDC Information 71
Glossary 73
Technical Support 79

3
http://www.tyan.com
Check the box contents!
1x S5211/S5211-1U motherboard
1 x Ultra-DMA-133/100/66/33 IDE cable
6 x Serial ATA cables
1 x USB2.0 cable
1 x S5211/S5211-1U user’s manual
1 x S5211/S5211-1U Quick Reference guide
1 x TYAN®driver CD
1 x I/O shield
If any of these items are missing, please contact your vendor/dealer for
replacement before continuing with the installation process.

4
http://www.tyan.com
NOTE

5
http://www.tyan.com
Chapter 1: Introduction
1.1 - Congratulations
You have purchased one of the most powerful server solutions available. The
Toledo i3210W/i3200R (S5211/S5211-1U) is a flexible Intel®platform for multiple
applications, based on the Intel®3210 (S5211) or 3200 (S5211-1U) MCH and
ICH9R chipsets.
Designed to support the family of Intel®Socket 775 processors and 8GB of DDR2
800/667 memory, the S5211/S5211-1U has integrated Dual Ethernet LAN’s, a built-
in 32MB XGI Z9S video controller and six SATA-II ports. This motherboard
represents the best choice for a server platform product.
Remember to visit TYAN®Website at http://www.tyan.com. There you can find
information on all of TYAN®products with FAQs, online manuals and BIOS
upgrades.
1.2 - Hardware Specifications
Processor
•Single LGA775 socket
•Support Intel®processors
- Quad-Core Intel®Xeon®processor
3300 and 3200 series
- Dual-Core Intel®Xeon®processor
3100 and 3000 series
- Intel®CoreTM 2 Extreme
- Intel®CoreTM 2 Quad processor
Q6000 sequence
- Intel®CoreTM 2 Duo processor
E6000 sequence
•1333/1066/800 FSB supported
Expansion Slots
S5211
•Two (2) PCI-E x 16 slots (w/x8 bus)
NOTE: If a PCI-E x16 VGA adapter is
inserted into PCI-E slots, the VGA
card will only work at PCI-E x1 speed;
this is a chipset limitation.
•Two (2) PCI-X 1.0 64/133 slots
•Two (2) 32/33 PCI 2.3 slots
S5211-1U
•One (1) PCI-E slot (w/x8 bus)
NOTE: If a PCI-E x16 VGA adapter is
inserted into this slot, the VGA card
will only work at PCI-E x1 speed; this
is a chipset limitation.
Integrated LAN Controllers
•Two (2) Intel i82573 GbE NICs
(1*82573V+1*82573L)
- operating at independent PCI-E x1
interface
Integrated I/O
•One IDE connector
•Six SATA (3Gb/s) ports
•Six USB 2.0 ports (2 at rear, 4 via
cable)
•Two COM ports (1 at rear, 1 via cable)
•TYAN®2x9 front-panel pin header
•TYAN®2x6 front-panel pin header for
LAN LED and ID LED/Switch
(reserved for OEM only)
•2x7 pin Fan header (reserved for OEM
only)
•2x3 pin LCM header (reserved for
OEM only)
•200pin vertical SO-DIMM for optional
TYAN®IPMI SMDC
Integrated USB IDE
(CY7C68300C)
•Single Ultra ATA channels for dual
ATA devices

6
http://www.tyan.com
Integrated SATA II (ICH9R)
•Supports six SATA-II ports running at
3.0Gb/s
•RAID 0/1/5/10 capable (Windows
driver support only)
Chipset
•Intel®3210 (S5211) or 3200 (S5211-
1U) MCH
•ICH9R South Bridge
•PXH-V 64-bit PCI Hub (S5211)
•SMSC SCH5027 Super I/O chip
•EZ-USB AT2 (CY7C68300C) Ultra
ATA controller
Integrated 2D PCI Graphics
•XGI Z9S
•32MB DDR2 frame buffer memory
Memory
•Four 240-pin DDR2 DIMM sockets
•Supports Un-buffered ECC DIMMs
•Maximum of 8GB DDR2-800/667
System Management
•SMSC SCH5027 and EMC6D103 with
hardware monitoring
•One (1) 3+1-pin CPU fan header with
tachometer monitoring and smart
FAN control (by SCH5027)
•Five (5) 3+1-pin system fan headers
with tachometer monitoring, three (3)
of them support smart FAN control
•Temperature and voltage monitoring
•Watchdog timer support
•Port 80 code display LED
Back Panel I/O Ports
•Stacked PS/2 mouse & keyboard ports
•Stacked 2 USB ports & RJ45 port for
OPMA
•One 9-pin COM port
•One 15-pin VGA port
•Two side-by-side RJ-45 ports
Optional Modules
•M3295, IPMI 2.0 Remote System
Management card
- Renesas H8S2167 BMC controller
- BT, KCS, logging support
- IPMI-over-LAN
- Remote power on/off and reset
•M3296, IPMI 2.0 Remote System
Management card
- KIRA100 (Single chip KVM/IP +
IPMI processor)
- 32MB SDRAM, 8MB Flash, 8MB
Video RAM
- Video output over LAN (1280x1024)
- USB 2.0 High Speed Interface
- LPC, GPIO, SMBUS
- 10/100 Mbps Ethernet Interface for
direct RJ45 connection
BIOS
•Phoenix BIOS on 8Mbit LPC Flash
ROM
•Serial Console Redirect
•USB boot supported
•Supports ACPI
•PnP, DMI2.0, WfM2.0 power
management
•S0/S1/S4/S5 states supported
Power Supply
•ATX 12V
•Universal 24-pin + 8-pin power
connectors
Regulatory
•FCC Class B (DoC)
•European Community CE (DoC)
•BSMI
Form Factor
•ATX footprint
•12” x 9.6” (305mm x244mm)

7
http://www.tyan.com
Chapter 2: Board Installation
You are now ready to install your motherboard. The mounting hole pattern of the
Toledo i3210W/i3200R (S5211/S5211-1U) matches the ATX specification. Before
continuing with installation, confirm that your chassis supports an ATX motherboard.
How to install our products right… the first time
The first thing you should do is reading this user’s manual. It contains important
information that will make configuration and setup much easier. Here are some
precautions you should take when installing your motherboard:
(1) Ground yourself properly before removing your motherboard from the
antistatic bag. Unplug the power from your computer power supply and
then touch a safely grounded object to release static charge (i.e. power
supply case). For the safest conditions, TYAN®recommends wearing a
static safety wrist strap.
(2) Hold the motherboard by its edges and do not touch the bottom of the
board, or flex the board in any way.
(3) Avoid touching the motherboard components, IC chips, connectors,
memory modules, and leads.
(4) Place the motherboard on a grounded antistatic surface or on the antistatic
bag that the board was shipped in.
(5) Inspect the board for damage.
The following pages include details on how to install your motherboard into your
chassis, as well as installing the processor, memory, disk drives and cables.
NOTE DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN
DAMAGED.

8
http://www.tyan.com
2.1- Board Image
Toledo i3210W S5211
This picture is representative of the latest board revision available at the
time of publishing. The board you receive may or may not look exactly
like the above picture.

9
http://www.tyan.com
Toledo i3200R S5211-1U
This picture is representative of the latest board revision available at the
time of publishing. The board you receive may or may not look exactly
like the above picture.

10
http://www.tyan.com
2.2 - Block Diagram
NOTE: If a PCI-E x16 VGA adapter is inserted into PCI-E slots, the VGA card will only work
at PCI-E x1 speed; this is a chipset limitation.
Toledo i3210W S5211

11
http://www.tyan.com
NOTE: If a PCI-E x16 VGA adapter is inserted into PCI-E slot, the VGA card will only work at
PCI-E x1 speed; this is a chipset limitation.
Toledo i3200R S5211-1U

12
http://www.tyan.com
2.3 - Board Parts, Jumpers and Connectors
This diagram is representative of the latest board revision available at the time of
publishing. The board you receive may not look exactly like the above diagram.
Jumper Legend
 OPEN - Jumper OFF, without jumper cover
 CLOSED – Jumper ON, with jumper cover

13
http://www.tyan.com
Jumper/Connector Function
COM2 (J19) COM2 Header
FAN1/2/3/4/5/6 4-pin Fan Connector
USB1 (JP7) / USB2 (JP2) USB Front Panel Connector
TYFP1 (JP9) 18-pin Front Panel Connector
TYFP2 (J22) 12-pin Front Panel Connector
(reserved for OEM only)
J23 LCM Connector (reserved for OEM only)
IPMB (J4) IPMB Connector
J11 IPMI Connector (for TYAN®M3295/M3296)
J10 Riser Power Connector
J24 Barebone Fan Connector
(reserved for OEM only)
JP4 PCI-X Speed Select Jumper
CMOS (JP3) Clear CMOS Jumper

14
http://www.tyan.com
FAN1
TYFP1
FAN2
FAN3
FAN6
FAN4
TYFP2
FAN5

15
http://www.tyan.com
FAN1/2/3/4/5/6/: 4-pin Fan Connector
4-pin Fan
+12V
Speed Control
GN
D
Tachometer
1
Use these headers to connect the 4-pin cooling fans
to your motherboard to keep the system stable and
reliable.
These connectors support the tachometer monitoring
and auto fan speed control.
TYFP2 (J22): TYFP2 Connector (reserved for OEM only)
1 11
2 12
Pin Signal Pin Signal
1 LAN1 LED+ 2 LAN1 LED-
3 LAN2 LED+ 4 LAN2 LED-
5 NC 6 NC
7 ID LED+ 8 ID LED-
9 ID SW+ 10 ID SW-
11 Key Pin 12 Reserved
TYFP1 (JP9): Front Panel Header
The Front Panel Header is used to connect some control or signal wires from
motherboard to chassis, such as HDD LED, power LED, power button, and
reset button.
Chassis Intrusion # 18 17 SMBUS Clock
GND 16 15 SMBUS Data
Key Pin 14 13 +5VSB
Warning LED - 12 11 NMI
Warning LED+ 10 9 GND
GND 8 7 Reset SW+
PWR SW # 6 5 GND
PWR LED- 4 3 HDD LED-
PWR LED+ 2 1 HDD LED+

16
http://www.tyan.com
COM2
IPMB
USB2
USB1
J10
J23

17
http://www.tyan.com
USB1 (JP7) / USB2 (JP2): USB Front Panel Connector
1 9
2 1 0
Pin Signal Pin Signal
1 PWR 2 PWR
3 USB_A- 4 USB_B-
5 USB_A+ 6 USB_B+
7 GND 8 GND
9 Key Pin 10 GND
Use these headers to connect to the USB devices via
the enclosed USB cable.
COM2 (J19): COM2 Header
1 9
2 10
Use these pin definitions to connect a port to COM2.
*TYAN®does not provide cable for this header. It is designed for OEM
use only.
Pin Signal Pin Signal
1 DCD 2 DSR
3 Rx 4 RTS
5 Tx 6 CTS
7 DTR 8 RI
9 GND 10 NC
IPMB (J4): IPMP Connector
1
Pin Signal Pin Signal
1 IPMB_SDA 2 GND
3 IPMB_SCLK 4 NC
J10: Riser Power Connector
GN
D
V5 +12V
GN
D
1
Pin Signal Pin Signal
1 +12V 2 GND
3 GND 4 V5
J23: LCM Header (reserved for OEM only)
5 1
6 2
Pin Signal Pin Signal
1 V5 2 RX
3 Key Pin 4 GND
5 V5DUAL 6 TX

18
http://www.tyan.com
JP4
J24
SATA3
SATA4
SATA2
SATA1
SATA5
SATA0
CMOS

19
http://www.tyan.com
J24: Barebone Fan Connector (reserved for OEM only)
1
2
13
14
Pin Signal Pin Signal
1 FAN1_TACH 2 FAN6_TACH
3 FAN2_TACH 4 Reserved
5 FAN3_TACH 6 Reserved
7 FAN4_TACH 8 Reserved
9 FAN5_TACH 10 Reserved
11 GND 12 Key Pin
13 GND 14 PWM
SATA0/1/2/3/4/5: SATA RAID Connector
7
1
Connects to the Serial ATA ready drives via the Serial
ATA cable.
Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7
GND TXP TXN GND RXN RXP GND
JP4: PCI-X Speed Select Jumper
3
1
Pin 1-2 Closed: 133MHz (Default)
13
Pin 2-3 Closed: 100MHz max.
CMOS (JP3): Clear CMOS Jumper
3
1
Normal
(Default)
13
Clear
Use this jumper when you have forgotten your
system/setup password or need to clear the system
BIOS settings.
How to clear the CMOS data
-Power off system and disconnect the power
supply from the AC source
-Use jumper cap to close Pin 2 and 3 for several
seconds to Clear CMOS
-Replace jumper cap to close Pin 1 and 2
Reconnect the power supply to the AC source
-Power on system

20
http://www.tyan.com
2.4 - Tips on Installing Motherboard in Chassis
Before installing your motherboard, make sure your chassis has the necessary
motherboard support studs installed. These studs are usually metal and are gold
in color. Usually, the chassis manufacturer will pre-install the support studs. If
you are unsure of stud placement, simply lay the motherboard inside the chassis
and align the screw holes of the motherboard to the studs inside the case. If
there are any studs missing, you will know right away since the motherboard will
not be able to be securely installed.
Some chassis’ include plastic studs instead of metal. Although the plastic studs
are usable, TYAN®recommends using metal studs with screws that will fasten
the motherboard more securely in place.
Below is a chart detailing what the most common motherboard studs look like
and how they should be installed.