Tyco Electronics T200 IDENT User manual

T200 IDENT Printer
Thermal Transfer Printer
Operator's-Manual
(412-121029 Revision 1)

2 2
3
Operator's Manual
Edition: 412-121029 rev 1
Copyright
This documentation as well as translations hereof are property of TE Connectivity.
The replication, conversion, duplication or divulgement of the whole manual or parts of it for
other intentions than its original intended purpose demand the previous written authorization by
TE Connectivity.
Trademark
Centronics® is a registered trademark of the Data Computer Corporation.
Microsoft® is a registered trademark of the Microsoft Corporation.
Windows 2000®, 2003®, XP®, Windows 7® are registered trademarks of the Microsoft
Corporation.
TrueTypeTM is a registered trademark of Apple Computer, Inc.
Editor
Regarding questions or comments please contact TE Connectivity.
Topicality
Due to the constant further development of our products discrepancies between documentation
and product can occur.
Terms and conditions
Deliveries and performances are effected under the General conditions of sale of TE Connec-
tivity, except that any open source software included in this product is solely governed by the
terms of the applicable open source software license agreement.
Global Identication Technical Contact Information
Printer & Software Technical Support:
http://www.te.com/catalog/Presentations/Global Identication Technical Contact Information.pdf
United States
Toll Free: 1-800-430-7226 x4 (East) or x5 (West)
Email: [email protected]
United Kingdom
Toll Free: 0 800988 9177
*Phone is monitored in the afternoon local time
Email: [email protected]
Germany
[phone]
Email: [email protected]
Ireland
Toll Free: 800-557-810
*Phone is monitored in the afternoon local time
Email: [email protected]
Rest of Europe
http://www.te.com/help
Email: [email protected]
Asia
[phone]
Email: [email protected]
Australia
Toll Free: 1-800-144-078
Email: [email protected]
New Zealand
Toll free: 0800-TYCO-HELP
Email: [email protected]

2
3
3
Table of Contents
1 Introduction ....................................................................................5
1.1 Product Description .........................................................................5
1.2 Instructions ......................................................................................5
1.3 Intended Use ...................................................................................6
1.4 Disclaimer ........................................................................................6
1.5 Safety Instructions ...........................................................................6
1.6 Environment .....................................................................................7
2 Installation ......................................................................................8
2.1 Printer Overview ..............................................................................8
2.2 Unpacking and Setting-up the Printer ..............................................9
2.3 Connecting the Printer ...................................................................10
2.3.1 Connecting to the Power Supply ................................................10
2.3.2 Connecting to a Computer or Computer Network ......................10
2.4 Switching on the Printer ................................................................. 11
3 Control Panel ...............................................................................12
3.1 Structure of the Touchscreen Display ............................................12
3.2 Operating the Touchscreen Display ...............................................12
3.3 Symbols on the Start Display .........................................................13
3.4 Printer States .................................................................................14
4 Loading Media ..............................................................................15
4.1 Loading Media from Roll ................................................................15
4.2 Loading Externally Fed and Fanfold Media ...................................16
4.3 Adjusting the Media Sensor ...........................................................17
4.4 Loading Transfer Ribbon ...............................................................18
4.5 Setting the Feed Path of the Transfer Ribbon ...............................19
5 Cutter / Perforator (Option) .........................................................20
6 Printing Operation .......................................................................21
6.1 Printing in Tear-off Mode (For Labels only) ....................................21
6.2 Printing in Cutting Mode ................................................................21
6.3 Synchronizing the Media Feed ......................................................21
7 Maintenance .................................................................................22
7.1 Cleaning Instructions .....................................................................22
7.2 Cleaning the Printhead ..................................................................22
7.3 Changing the Printhead .................................................................23
7.4 Cleaning or Replacing the Print Roller ...........................................24
7.5 Cleaning Cutter / Perforator and Replace Blades ..........................25
8 Fault Correction ...........................................................................27
8.1 Types of Errors ..............................................................................27
8.2 Problem Solution ...........................................................................27
8.3 Error Messages and Fault Correction ............................................29

4 4
5
Table of Contents
9 Licences .......................................................................................32
9.1 EC Declaration of Conformity ........................................................32
9.2 FCC ...............................................................................................33
9.3 Open Source Software Information ...............................................33
10 Index .............................................................................................39

4
5
5
1.1 Product Description
The device is an industrial thermal transfer printer for printing TE Connectivity
cable Identication and label products hence forth referred to as media.
1.2 Instructions
Important information and instructions in this documentation are designated
as follows:
Danger!
Draws your attention to an exceptionally grave, impending danger
to your health or life.
!
Warning!
Indicates a hazardous situation that could lead to injuries or
material damage.
!
Attention!
Draws attention to possible dangers, material damage or loss of
quality.
i
Notice!
Gives you tips. They make a working sequence easier or draw
attention to important working processes.



Environment!
Gives you tips on protecting the environment.
Handling instruction
Reference to section, position, illustration number or document.
Option (accessories, peripheral equipment, special ttings).
Time Information in the display.
1 Introduction

6 6
7
1.3 Intended Use
• The printer is manufactured in accordance with the current technological
status and recognized safety rules. However, danger to the life and limb
of the user or third parties and/or damage to the printer and other tangible
assets can arise during use.
• The printer may only be used for its intended purpose and if it is in perfect
working order, and it must be used with regard to safety and dangers as
stated in this operating manual.
• The printer is intended exclusively for printing suitable TE Connectivity (TE)
approved media. Any other use going beyond this shall be regarded as
improper use. The manufacturer/supplier shall not be liable for damage
resulting from unauthorized use; the user shall bear the risk alone.
• Usage for the intended purpose also includes complying with this
manual, including the manufacturer‘s maintenance recommendations and
specications.
1.4 Disclaimer
While TE has made every reasonable effort to ensure the accuracy of the
information in this document, TE does not guarantee that it is error-free,
nor does TE make any other representation, warranty or guarantee that the
information is accurate, correct, reliable or current. TE reserves the right to
make any adjustments to the information contained herein at any time without
notice. TE expressly disclaims all implied warranties regarding the infor-
mation contained herein, including, but not limited to, any implied warranties
of merchantability or tness for a particular purpose. The dimensions in this
document are for reference purposes only and are subject to change without
notice. Specications are subject to change without notice. Consult TE for the
latest dimensions and design specications.
Only the English Language version of this document is legally binding
i
Notice!
The complete documentation is included on the enclosed DVD
found in the printer box.
1.5 Safety Instructions
• The printer is congured for voltages of 100 to 240 V AC. The printer must
be connected to a grounded socket.
• Only connect the printer to other devices which have a protective low
voltage.
• The printer may only be used in a dry environment, do not expose it to
moisture (sprays of water, mists, etc.).
• Do not use the printer in an explosive atmosphere.
• Do not use the printer close to high-voltage power lines.
1 Introduction

6
7
7
• When the printer is in operation the cover must be closed. However when
loading or operating the printer, ensure all loose clothing, long hair, jewelry
etc, do not come into contact with the exposed rotating parts.
• The printer or parts of it can become hot while printing. Do not touch
during operation, and allow to cool down before changing media and
before disassembly.
• Risk of crushing when closing the cover. Touch the cover at the outside
only. Do not reach into the hinge range of the cover.
• Perform only those actions described in this operating manual.
Work going beyond this may only be performed by trained personnel or
service technicians.
• Unauthorized interference with electronic modules or their software can
cause malfunctions.
• Other unauthorized work on or modications to the printer can also
endanger operational safety.
• Always have service work done in a qualied workshop, where the
personnel have the technical knowledge and tools required to do the
necessary work.
• There are various warning stickers on the printer. They draw your attention
to dangers.
Warning stickers must therefore not be removed, as then you and other
people cannot be aware of dangers and may be injured.
• The maximum sound pressure level is less than 70 dB(A).
Danger!
Danger to life and limb from power supply.
Do not open the printer casing.
1.6 Environment



Obsolete printers contain valuable recyclable materials that should be sent
for recycling.
Send to suitable collection points, separately from residual waste.
The modular construction of the printer enables it to be easily disas-
sembled into its component parts.
Send the parts for recycling.
The electronic circuit board of the printer is equipped with a lithium battery.
Take old batteries to collection boxes in shops or public waste disposal
centers..
1 Introduction

8 8
9
2.1 Printer Overview
1
2
3
4
5
6
7
8
1 Cover
2 Margin stops
3 Media roll retainer
4 Ribbon supply hub
5 Ribbon take-up hub
6 Roller
7 Print mechanics
8 Touchscreen display
Fig. 1 Printer with Tear-off Plate
9
9 Cutter or Perforator
Fig. 2 Printer with Cutter or Perforator
2 Installation

8
9
9
13
15
12
10 11
1617
14
10 Media sensor
11 Printhead retainer with
printhead
12 Media guides
13 Knob for adjusting the guides
14 Knob for adjusting the media
sensor
15 Lever for locking the
printhead
16 Tear-off plate
17 Print roller
Fig. 3 Print Mechanics
2.2 Unpacking and Setting-up the Printer
Lift the printer out of the box and set it up on a level surface.
Check printer for damage which may have occurred during transport.
Check delivery for completeness.
Contents of Delivery:
• T200 Ident Printer
• Power Cable EU
• Power Cable UK
• Power Cable US
• Cardboard Core
• Operator's Manual
• DVD with demo versions of Wintotal and Printeasy, Windows driver and
documentation
• USB Cable
i
Notice!
Please keep the original packaging in case the printer must be
returned.
i
Notice!
When transporting the printer remove the transfer ribbon and media.
!
Attention!
The printer and media can be damaged by moisture and excessive
dust contamination.
Set up the Printer in a dry location protected from splashed
liquids, and sources of excessive dust.
2 Installation

10 10
11
2 Installation
2.3 Connecting the Printer
2
3
4
5
1
1 Power switch
2 USB master ports for
keyboard, scanner or
memory stick, Imax=500mA
3 USB full-speed slave port
4 Ethernet 10/100 Base-T
5 Power connection jack
Fig. 4 Connections
2.3.1 Connecting to the Power Supply
The printer is equipped with a wide area power unit for a supply voltage of
100 V to 240 V.
1. Check that the printer is switched off.
2. Plug the power cable into the power connection jack (5).
3. Plug the power cable into a grounded socket.
2.3.2 Connecting to a Computer or Computer Network
!
Attention!
Inadequate or no grounding can cause malfunctions during
operations.
Ensure that all computers and cables connected to the printer
are grounded.
Connect the printer to a computer or network by a suitable cable.