U.S. Products KING COBRA 1200 PRO User manual

KING COBRA®1200 PRO
100V
INFORMATION
&
OPERATING
INSTRUCTIONS
DO NOT OPERATE THE MACHINE UNTIL YOU HAVE READ
ALL SECTIONS OF THE INSTRUCTIONS
IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY
1. DANGER: High spraying pressure may cause severe injury. Always wear safety
glasses. Keep hands & feet away from spray. Never direct the spray towards people or pets.
2. Never allow the spray to remain fixed in one spot.
3. Before each use, remove the spray tool from the hose, and check to make sure the spray
nozzle is securely tightened to the spray tool. A loose nozzle could fly off during use.
4. If a leak occurs at the hose, IMMEDIATELY turn the machine off. Replace hose before
restarting.
5. Always use a defoamer when foaming occurs to prevent vacuum motor damage.
6. Keep the machine from rain and snow, extremes in temperatures, and store it in a heated
location. Use the machine indoors. Do not use outdoors.
6.5.2007
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

IMPORTANT SAFETY INSTRUCTIONS
This machine is only suitable for commercial use, for example in hotels, schools,
hospitals, factories, shops and offices other than normal residential housekeeping
purposes.
When using any electrical appliance, basic precautions should always be followed,
including the following:
NOTE:Read all instructions before using this machine.
WARNING!
To reduce the risk of fire, electric shock, or injury:
•Do not leave the machine unattended when it is plugged in. Unplug the unit from the
outlet when not in use and before servicing.
•To avoid electric shock, do not expose to rain or snow. Store, and use, indoors.
•Do not allow to be used as a toy. Close attention is necessary when used near children.
•Use only as described in this manual. Use only the manufacturer’s recommended attach-
ments.
•Never add water over 54 °C/130 °F to the solution tank.
•Do not use with damaged cord or plug. If the machine is not working as it should, has
been dropped, damaged, left outdoors, or dropped into water return it to a service cen-
ter.
•Do not pull by the cord, use the cord as a handle, close a door on the cord, or pull the
cord around sharp edges or corners. Do not run the machine over the cord. Keep the
cord away from heated surfaces. To unplug, grasp the plug, not the cord.
•Do not handle the plug, the cord, or the machine with wet hands.
•Extension cords must be 12/3 and no longer than 50 feet. Replace the cord or unplug
immediately if the ground prong becomes damaged.
•Do not put any object into openings. Do not use with any opening blocked; keep free of
dust, lint, hair, and anything that may reduce air flow.
•Keep loose clothing, hair, fingers, and all parts of body away from openings and moving
parts.
•Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot
ashes, or any health endangering dusts. Do not use the machine to pick up flammable
or combustible liquids such as gasoline or use it in areas where they may be present.
•Turn off all controls before unplugging.
•Use extra care when cleaning on stairs.
•Connect to a properly grounded outlet only.
•Liquid ejected at the spray nozzle could be dangerous as a result of its
temperature, pressure, or chemical content.
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

INSPECTION:
Carefully unpack and inspect your KING COBRA-1200 PRO for shipping damage. Each machine is
tested and inspected before shipping. Any shipping damage incurred is the responsibility of the
carrier. You should notify the carrier immediately if you notice damage to the box or to the machine
or parts.
CLEANING SOLUTIONS:
Select a proper pre-spray for the surface to be cleaned, and apply the pre-spray. Use a neutral pH
rinse or detergent (6 to 9 pH) in the King Cobra to prevent premature wear of the pumps, seals, and
other components. Damage caused by the use of improper or strong chemicals is not covered by
warranty. When cleaning carpets with the 500 psi pump, we recommend our Magic Fabric Cleaner.
Powders are not recommended.
MAINTENANCE:
For optimum performance, flush the machine with clear water at the end of each working day. Once
a month, minimum, run a flushing compound through the machine to break up any mineral or
chemical build-up that may have formed. U.S. Products “X-1500” is recommended. The vacuum
motor, pump motors, and the pumps do not require any scheduled maintenance; however, the
motors may require replacement brushes after 1000 - 1500 hours, and the high pressure pumps and
unloader valves may require rebuild kits after 500 -1000 hours (refer to machine part list for
numbers). Clean the body with an all purpose detergent, and protect it with an automobile interior
polish. Lubricate the wheels, castors, and quick disconnects with an all purpose silicone spray.
Record the serial number and model of your new extractor here:
(and be sure to register your purchase to activate your warranty: go to www.usproducts.com)
Serial Number: __________________ Model: KING COBRA-1200 PRO 100V___
Purchase Date:_____________
Write the name and phone number of your distributor:
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

HEAT
500 P.S.I.
O
I
O
1200 P.S.I.
I
I
O
I
O
I
SWITCH PLATE
CIRCUIT LOCATOR
LIGHT INDICATES
TWO CIRCUITS.
5
1200 PSI
PUMP
(NOHEAT)
DUMPPUMP
ON/OFF
SWITCH
1
1200 PSI
PUMP or
HEAT
SELECTOR
SWITCH
500 PSI
PUMP
ON/OFF
SWITCH
3
VACUUM
ON/OFF
SWITCH
24
HEAT
SELECT
Hoses
Vacuum
Hose
Connection Auto-fill
Basket
Wheel
Recovery
Dump
Hose
Castor
Switches
Auto-Dump
Pump
Power
Cord
Recepticle
Power Prime
Pedal
Base
Compartment
Vac
Tank
Latch
Chemical
Pick-up hose
Solution
Tank
1200 PSI
Quick
Disconnect
500 psi
Quick Disconnect
500 psi
Gauge
Pressure
Adjust
Knob
KC-1200/500
RED
HEAT
LIGHT
GREEN
LIGHT
1200 psi
Gauge
Wand Holder
Chemical
Pick-up hose
Chemical
Metering
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

1200 PSI HIGH PRESSURE WASHER
1 Before each use, inspect the machine, hoses, and cleaning tools for cleanliness and completeness.
Make sure the hoses are in good condition and the spray nozzle(s) is tight.
2. When not using the auto-dump feature, just make sure the brass cap is screwed tightly on the hose
connector fitting on the rear of the machine. If you choose to use the auto-dump, connect the dump
hose to brass hose fitting on the back of the machine,and place the open end of the hose in a drain.
Make sure the drain hose (recovery tank) is closed, and the lid is tight on the recovery tank.
REFER TO THE AUTO-FILL AND AUTO-DUMP INSTRUCTIONS ON THE FOLLOWING PAGES.
3. If you choose to use the auto-fill feature, connect the fill hose to the auto-fill valve (located over the
solution tank fill hole). Place your gallon of chemical in the chemical basket on the recovery tank lid,
and put the weighted foot valve into the gallon. Turn on the water source, and allow the tank to fill with
solution. When using the auto-fill system, the auto-fill valve will automatically turn on and turn off as
the tank empties and then fills. NOTE: If you are not going to use the auto-fill system, just fill the
tank with water and cleaning chemical. Follow chemical directions regarding dilution and mixing. Do not
use harsh chemicals; they may damage seals in pumps and valves, and cause the pump to wear
prematurely. NOTE: Never use water with a temperature exceeding 130 °F / 54 °C.
REFER TO THE AUTO-FILL AND AUTO-DUMP INSTRUCTIONS ON THE FOLLOWING PAGES.
4. Pre-spray the area to be cleaned, with a pump-up sprayer, while the tank is filling. Follow chemical
directions.
5. Connect the solution hose (from the reel) to the 1200 PSI Quick Disconnect on the front of the tank,
below the switch plate.
6. Plug in the two power cords. Do not connect both cords to the same outlet. The green, ‘separate
circuit’ locator light (1) on the switch plate should light up. If the locator light does not come on, check
the circuit breaker box in the wall, and/or try different outlets until it does turn on. Although all systems
in the machine may work correctly if you are not on two circuits, a circuit breaker in a wall panel may
trip. If you make sure the green light is turned on, you will prevent tripped circuit breakers. Turn on the
1200 PSI pump by placing the HIGH PRESSURE/HEAT selection switch (2) in the UP position, to select
the 1200 PSI Pump. NOTE: both the 1200 PSI pump and the heat can not operate at the same
time. NOTE: this switch (2) is off when it is set to the middle position and neither the 1200 PSI pump
nor the heater is selected.
8. Prime the 1200 psi pump using the ‘power prime’ system: turn on both the pump and the vacuum
(3), cover the hole in the vacuum hose barb on the top of the machine with your hand, then depress
the Power Prime Pedal (located on the back of the machine). This will pull trapped air through the
pump and into the recovery t ank, priming the pump. Y ou should notice a change in the ‘tone’ of the
pump (smoother, with less rattle), and the water being pulled into the recovery t ank will change from a
white, sputtering flow to a clear , solid stream. NOTE: priming requires a full Holding t ank, and it may
take between 20 to 90 seconds. Once the pump has primed, release the Power Prime Pedal, and turn
both the pump and the vacuum off. Momentarily depress the Power Prime pedal again to release any
built-up back pressure. Proceed to Step 9.
OPERATION
REFER TO THE DIAGRAMS ON THE PREVIOUS PAGE
CAUTION: Use care when handling hazardous chemicals.
CAUTION: Never leave the machine running when you are not
actively using it.
DANGER: Do NOT use solvents, or any chemicals that may be
flammable, explosive, or combustible.
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

OPERATION OF THE 1200 PSI PUMP CONTINUED:
9. Add defoamer to the recovery tank.
10. Your machine has two solution outputs. The solution output for the 1200 psi pump is a quick disconnect
located just below the fill hole on the holding tank, on the front face of the machine (the 500 psi outlet is a
quick disconnect on the end of a short length of hose, on the front of the base section of the machine).
Attach the solution spray hose from the reel to the 1200 psi solution quick disconnect. Attach the
vacuum hose on the reel to the hose barb on the front of the recovery tank. Pull the hoses out from
the reel. Attach the other ends of the hoses to the cleaning tool.
11. Turn on the vacuum (3) and turn on the dump pump (5), if you have set-up the dump hose. Begin
cleaning. NOTE: the dump pump will automatically turn on and turn off as the tank fills and then empties
(refer to drawings on next pages).
12. When the job is finished, turn off the water source (if you are using the auto-fill feature), and turn off the
pumps. Disconnect the vacuum hose from your cleaning tool, and vacuum any remaining solution from
the holding tank into the recovery tank.
13. Completely drain the recovery tank by pouring the dirty water out through the drain hose on the rear of
the machine. Disconnect the solution hose from the cleaning tool, and reel the hoses onto the hose
spool.
14. Unplug the power cords.
15. Clean the machine and the tool. Never store your machine outside, and keep it from getting too hot or
too cold.
OPERATION
500 PSI AND HEAT
1. Before each use, inspect the machine, hoses, and cleaning tools for cleanliness and completeness. Make
sure the recovery tank drain hose is closed, and the lid is tight on the recovery tank. Make sure the hoses
are in good condition and the spray nozzle(s) is tight.
2. If you choose to use the auto-dump, connect the dump hose to brass hose fitting on the back of the
machine, and place the open end of the hose in a drain. Make sure the drain hose, on the rear of the
recovery tank, is closed and the lid is tight on the recovery tank. If you choose not to use the auto-
dump feature, make sure the brass cap is screwed onto the hose connector on the back of the machine
and the dump pump switch is turned off. Refer to drawings on following pages.
REFER TO THE AUTO-FILL AND AUTO-DUMP INSTRUCTIONS ON THE FOLLOWING PAGES.
3. If you choose to use the auto-fill feature, connect the fill hose to the auto-fill valve over the solution tank.
Place your gallon of chemical in the chemical basket, and put the weighted foot valve in the gallon.
Connect the other end of the hose to the water source. Turn on the water and allow the tank to fill with
solution -- a float in the tank will shut off the water flow once the tank is full. If you are not going to use
the auto-fill system, just fill the tank with clean water and a liquid cleaning chemical. Follow chemical
directions regarding dilution and mixing. CAUTION: Do not use harsh chemicals in your King Cobra 1200
Pro; they may damage seals in pumps and valves and could cause the pump to wear prematurely.
NOTE: using warm water in the tank may improve the efficiency of the heat exchanger when cleaning
with heat, but never use water with a temperature exceeding 130 °F / 54 °C.
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

4. Select ‘HEAT” by moving the HEAT/HIGH PRESSURE switch (2) towards the thermometer symbol.
NOTE: this switch is off when it is set to the middle position and neither the 1200 PSI pump nor the
heater is selected. When set to the bottom position, the heat is selected; the red light will come on
and stay on. NOTE: The heater and the 1200 PSI pump can not operate at the same time.
5. Plug the power cords into separate circuits. The green, circuit locator light (1) on the switch plate should
light up. If the locator light does not come on, check the circuit breaker box in the wall, and/or try
different outlets until it does turn on. Although all systems in the machine may work correctly if you are
not on two circuits, a circuit breaker in a wall panel may trip. If you make sure the green light is turned
on, you will prevent tripped circuit breakers.
6. Press the ‘power prime’ pedal (located on the rear, lower left of the machine) for a moment to release
any back pressure in the pump lines.
7. Connect the priming/siphon hose to the 500 psi quick disconnect (lower, right, front on the end of a short
hose) and turn on the pump (4). The air should prime out of the pump within 20 - 60 seconds. Watch
the water flow into the recovery tank through the lid. When the water is clear (no air in it) and
flowing strongly, turn the pump off and remove the priming hose.
8. Connect the solution hose from the reel to the 500 PSI quick disconnect, and connect the vacuum hose
from the reel to the hose barb on the top, left of the recovery tank. Connect both hoses to
the cleaning tool.
9. Turn ON the 500 PSI pump (4). Set the pump to the desired pressure by adjusting the pressure
regulator cap (lower front) while you are spraying and watching the 500 psi pressure gauge. NOTE: the
gauge will only read pressure while you are spraying.
10. Spray for a few seconds to fill the lines with solution. Wait two minutes to allow the heater to reach
temperature.
11. Turn on the vacuum (3) and turn on the dump pump (5). Begin cleaning. NOTE: the dump pump will
automatically turn on and turn off as the tank fills and then empties (refer to drawings on following
pages). Itmay take several cycles to heat the lines and the cleaning tool.
12. If you are not using the auto-fill and auto-dump features, turn off both the pump and vacuum when the
solution tank gets low, fill the solution tank, and empty and clean the recovery tank.
13. When finished with the job, turn off the water source (if using Autofill). Vacuum the remaining solution
from the holding tank into the recovery tank. Pump a few gallons of clean water through the system.
Drain the recovery tank by placing the drain hose over a drain or into a bucket, and removing the cap.
When the tank is empty, cap the drain hose and place it back in the velcro strap holder. Disconnect the
hoses from the cleaning tool, and reel them up onto the hose spool.
14. Unplug the power cords. Clean the machine and the tool.
OPERATION OF THE 500 PSI PUMP and HEAT CONTINUED:
ELECTRIC CIRCUIT LOCATOR: This system will inform the operator when the two cords are plugged
into separate circuits by turning on the green, circuit locator light. This helps to prevent tripping circuit
breakers.
NOTE: if the green, circuit locator light does not illuminate when the cords are plugged in, then both cords
are on the same circuit. Try other outlets with one of the cords until you get the locator light to come on.
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

USING THE AUTO-FILL AND/OR AUTO-DUMP FEATURES
1Chemical Supply:
• Place the container of concentrated chemical cleaner -- use a product with a pH between 6 and 9 to avoid premature
pump wear (which would void the warranty) -- in the holder on top of the recovery tank.
• Remove the cap on the container. Insert the end of the clear tubing with the foot valve into the container. NOTE: the
stainless steel weight at the foot valve will keep the valve at the bottom of the chemical container.
• The chemical flow may be turned on or off by applying the pinch clamp to the tubing, between the chemical container
and the auto-fill valve.
2Chemical Injection Flow Rate:
• Metering tips are used to control the rate at which the cleaning chemical feeds into the supply water.
The following table illustrates the ratio of chemical, in ounces, to each gallon of water coming into the tank. The tips
are color coded for ease of use.
•NOTE: the flow rate values in the table are based on a chemical with the same viscosity as water.
3Operation:
• Attach a 3/4” garden hose to the autofill valve, and connect the other end of the hose to your water source.
• Make sure the float that hangs from the autofill valve into the tank is free of obstruction and can move freely.
• Turn the water supply on.
• As the tank fills, the chemical concentrate will be drawn from the chemical container, will pass through the clear tubing
to the valve, and will be mixed into the water stream.
• The autofill float will automatically shut-off the flow of incoming water when the tank is nearly full, and it will allow the
valve to open again once the water level has dropped to a predetermined level.
AUTO-FILL
To change the metering tip: find the, plastic hose-clamp on the chemical feed tubing, near the Auto-fill valve. Refer to
illustration above. Open the clamp by sliding the two ends of clamp (where they come together) apart, sideways, in opposite
directions until the clamp opens. Then pull the clear chemical supply hose off the hose barb at the Auto-Fill valve. Unscrew
the metering tip from the end of the hose barb. Select the tip that will provide you with the desired chemical ratio (see chart,
above). Screw the selected tip into the end of the hose barb. Snug-up the tip, but do not overtighten. Slide the hose back
over the tip and the hose barb. Install the clamp onto the hose so it is over the hose barb, and squeeze the clamp closed.
* NOTE: the turquoise colored tip is factory installed
(provides a 1 to 1 ratio -- see table).
METERING TIP FLOW RATES
COLOR OZ/GAL
WHITE 3.00
GREEN 3.50
BLUE 4.00
YELLOW 5.25
BLACK 6.75
PURPLE 10.50
GRAY 14.00
COLOR OZ/GAL
TAN 0.60
ORANGE 0.70
TURQUOISE* 1.00
PINK 1.25
LIGHT BLUE 1.75
BROWN 2.00
RED 2.75
Chemical
Holder
Basket
Pinch
Clamp
Chemical
Proportioner
&
Auto-fill
Valve
Hose
Connection
AUTO-FILL
Clamp
Chemical
Supply
hose
Chemical
Pick-up
Tube
CAUTION: Use care when handling
hazardous chemicals.
DANGER: Do NOT use solvents, or
any chemicals that may be flammable,
explosive, or combustible.
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

DANGER: DO NOT USE SOLVENTS, OR ANY CHEMICALS THAT MAY BE
FLAMMABLE, EXPLOSIVE OR COMBUSTIBLE.
CAUTION: always use a defoamer in the recovery tank to prevent water or foam from
entering the vacuum motor.
CAUTION: if the dump pump is not going to be used for a month or longer, remove the pump
impeller cover, pull the rubber impeller out, clean it and apply a generous coating of petroleum
jelly to the impeller before replacing it in the pump. Make sure the gasket is in place and in good
condition before you screw the impeller cover back on.
1Operation:
Before each use: if necessary, unscrew the stainless steel filter at the bottom of the recovery tank and clean
it. Also make sure the float in the recovery tank is clean.
• Attach a 3/4” garden hose to the dump pump outlet fitting on the back of the base of the machine.
Refer to illustration below
• Run the other end of the hose into a drain.
• Turn the dump pump switch ON (switch is located on the switch panel on the top of the machine).
•NOTE: the dump pump will only run when the tank is full enough to activate the float switch.
•NOTE: the dump pump is ‘self-priming.’ You should see water start to flow within 30 seconds of the
pump turning on. If the water level in the tank is high enough to activate the float switch. If water does not begin
to flow, check the filter to see if it is plugged with debris.
After each job : run clear water though the dump pump to wash out any chemical residue.
Remove and clean the stainless steel filter in the back of the tank. Reinstall the filter once it is
clean. Clean and empty the recovery tank .
AUTO-DUMP
DANGER: always unplug the King Cobra from the electrical outlet(s) before
cleaning or maintaining. Certain internal components are electrically live,
even with switches in their OFF position.
Dump
Pump
Drain Hose
AUTO-DUMP
Power
Prime
Hose
Power
Prime
Pedal
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

18
16
17
15
14
8
47
20 21
22
23
24
32
33
30
67
5
4
3
29
34
35
3C
2
1
13
12
12A
11
10
3B
99A
26
1A
55 56
65
58 60
59
63
62
66A
61
32
32
48
57
3A
2
2A
49
49
51
28
76
64
44
42 43
45
7
7A
26A
145
95
89
88
98
86
91
90
93
87
100
38
31
37
41
46
49
49
39
28
28
36
6
KC-1200 PRO
120V
11/2/2006
110
110A
82
72
83
79
6968
74
75
104
101
102
83
105
106
107
108
111
78
79
121
122
123
128
127
124
138
139
140
142
143
66
112
80
99
to outlet
102
135A
75
111A
136
24
78
81
137
130
70
92
92
73
140
113 114
116
95
84
94
73
75
75
146
135
26B
133
27
12
43
110B
100V
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

KING COBRA-1200 PRO
PART LIST
11/2/2006
1160K Pump valves & o-rings, 1200 psi
1160A Pump, plunger and seals, 1200 psi
1159 Motor, 1.5 HP, for 1200 psi pump
953A Metering tip replacement kit
FP256 Heat repair kit, includes cutout,
bimetallic switch, & heat sink
grease
FP372 Pump w/hose, unloader, cam &
bearing & no motor
100 V
MISCELLANEOUS PARTS
121 2084A Wheel,10”
122 27A Axle cap
123 1105 Axle, 1/2” X 21”
124 1158 Plate,pumpmounting
127 2015 Guard,fan
128 2014 Fan,cooling,100CFM
130 BKCR BLK Basecompartment,black
133 1081 Elbow,90degree,pumpinlet
135 905 Castor,4”
135A 905A Brake,forcastor
136 1413 ClipHolder,forhose
137 FP416 Hoseassy,lowpress.outltet
138 1043A Gasket
139 219 Quickdisconnect,male
140 91 Elbow,90degree
142 1165 Gauge,2000psipressure
143 908A Latch
145 1327 TerminalBlock
146 951B Gauge,500psipressure
ITEM PART No. DESCRIPTION
55 7 Locknut, 5/16” jam
56 15 Washer,flat,5/16”
57 959 Gasket,forvacuum
58 320AB Nut,finish,5/16
59 34 Washer,splitlock
60 179 Bolt,5/16X4”
61 1131 Elbow, PVC
62 5 Bolt,1/4-20X3/4”
63 8 Locknut,1/4-20
64 926 Manifold,vacuum
65 FP323 Vacuummotor,w/gasket,complete
66 430 Vacuumhose,1-1/2”X7.75”
66A 1136 Vacuumhose,1-1/2”X25 ,clear
67 1310A Float,Auto-fill,hightemp.
68 216 Elbow,90degree
69 221 Quickdisconnect,male,open
70 1280 Elbow,brass,1/4fptX1/4fpt
72 1306A Manifold,fluiddirection
73 210 Pulsation‘Snubber’
74 221 Quickdisconnect,male,open
75 220 Quickdisconnect,female,open
76 2088 Pre-filter,vacuuminlet
78 219 QuickDisconnect,male,open
79 220 QuickDisconnect,female,open
80 1162 Hose,powerprimeinlet,32”
81 211 Plug,1/4mpt
82 1163 Valve,pressureregulator,1200psi
83 92A Nipple, S/S, 1/4 mpt
84 1057B Power Cord
86 8 Locknut,1/4-20
87 233 Washer,nylon,black
88 4 Bolt,1/4-20X1”
89 455 Bracket,heatermount
90 399 Thermostatswitch
91 76 Hose Clamp, 2-3/4”
92 FP420 Hose,PumptoGauge,complete
93 FP HeatExchanger,complete
94 SYP1 Priminghose,for500psi
95 928 Louver,3”,includesscrews
98 FP534 Hose,heatertooutlet
99 1162 Hose Assembly, 32”, bypass
100 1581 Hose,¼”x24”pumpto heater
101 141 Coupling,1/4fptbothends
102 152 “T”,brass/1/4npt
104 FP508 1200psipump&motor,complete
105 1062 Recepticle,powercord
106 957 Pump,auto-dump
107 1324 HoseConnector,dumppumpout
108 1325 Elbow,auto-dumpin
110 4405A Relay,20Amp
110A 2025 Heatsinkplate
110B 1579 Rectifier,bridge
111 1164 Valve,powerprime
111A 1299 Pedal,powerprime
112 FP415 Hose,manifoldtooutlet,HiPress.
113 FP507 500psipump,complete,nomotor
114 1582 Motor,for500psipump
116 FP509 Unloadercomplete
ITEM PART No. DESCRIPTION
1 FP500 Hose,ChemicalPick-up,complete
1A 1199 Check valve & filter
2 79B Wiretie,white,8”
2A 1323 Clamp,quick,pinchopening
3 1303 SwitchPlate
3A 78 Light,green,1200psipump
3B 78B Light,red,heat
3C 227 Light,green,dualcircuit
4 FP417 Switch,3-wayselector,withknob
5 FP345 Switch,ON/OFF, with actuator
6 921 Elbow, PVC
7 1140 PVC, “T”
7A 929A Vacshut-offball,vacuuminlet
8 2068 Float,Auto-dump
9 230 CordRetainer,watertight
9A 230A Nut,nylon
10 805 Chain,lidretaining
11 1074 Gasket,recoverylid
12 2086 Lid,andring,6”
12A 1156 Screw, 8-32 x 1-1/8”
13 1169 Basket,chemicalcontainer
14 937 Bushing, PCV
15 2069 Filter,Auto-fill
16 1060C Plug,drainhose
17 1130 Strap,velcro
18 1060B Hose, drain
20 91 Elbow,90degree,brass,1/4mpt
21 1141 Washer,S/S
22 1146 Pipe,S/S,1/4mptbothends
23 1143 Spacer,insulated
24 45 QuickDisconnectmale,1/4pt
25 1184 Hoseconnector,inletwatersupplyline
26 1307 Valve,autofill,withmeteringbarb
26A 1184 Adapter,gardenhose
26B 1200 Connector,gardenhosemale
27 1308A Hose,from autofill valve to float,1/2”X5”
28 1400 Clamp,hose,quickdisconnect
29 1189 HoseBarb,1/2”hose,mpt
30 1320 Bracket,Auto-fillvalvemounting
31 156 Hoseclamp,2-1/4”
32 907 HoseBarb,1-1/2”hose
33 1137 Adaptor,ABS,1-1/2”
34 HKCR-1 HoldingTank,white
35 VKCR-1 RecoveryTank,white
36 FP414 Reel,withhoses,complete
37 1309 Hose, power prime outlet, 3/8” X 21.25”
38 166 Hoseclamp
39 1308 Tubing,1/2”IDX10”
41 1115 Elbow,90deg,3/8”hoseX1/4mpt
42 290 Washer,rubber,70Durometer
43 1345 Washer, flat, S/S, 1/4”ID X 1” OD
44 1350 Bracket,forautofillfloat
45 1349 Spacer,bushing
46 1113 Elbow,90deg,1/2”hoseX1/2mpt
47 92B Nipple, PVC, 1/2 npt
48 207A Filter,Pumpinlet
49 1402 Clamp,quickdisconnect,small
51 CWKC-BLK CordWrap,black
ITEM PART No. DESCRIPTION
https://harrissupplyind.com-ToOrderPartsCall608-268-8080

SPECIFICATIONS:
KING COBRA
®
1200 PRO
100V
Rotomolded Body:
Vacuum:
VAC Shutoff:
Pump:
Heat:
Capacity:
Cords:
Size:
Autodump:
Wheels:
Hoses:
Plus:
Lifetime Warranty
7.2” 3-stage, 140” of water lift
Ball Float
Positive displacement, fully adjustable 0-500 psi &
Positive displacement, 1200 psi, 2.2 gpm
1500 Watts
16 gallon solution tank; 14 gallon recovery tank
two, detachable 12/3, hospital grade plugs
39” H X 21” W X 36” L
5.5 gpm with electronis shut-off
10”, locking, non-marking
25 ft hoses on a reel (patent pending)
Auto-fill
Power Prime system
https://harrissupplyind.com-ToOrderPartsCall608-268-8080