Ubiquiti G3 Micro User manual

micro
1080p Wireless IP Security
Camera with Infrared
Model: UVC-G3-MICRO

Introduction
Thank you for purchasing the Ubiquiti Networks® UniFi® Video
Camera G3 Micro. This Quick Start Guide is designed to guide
you through installation and also includes warranty terms.
Package Contents
UVC-G3-MICRO Camera Power Adapter
802.3af Instant
PoE Adapter
Instant PoE Cover Table Stand
Wall Mounts
(Qty. 2)
Instant PoE
Mount
Angle Mount Adhesives
(Qty. 2)
micro
1080p Day/Night
IP Security Camera
with Infrared
Model: UVC-G3-MICRO
Screws and Anchors
(Qty. 4)
Cable Clips
(Qty. 8)
Quick Start Guide

Before You Begin
The UVC G3 Micro is designed to work with the UniFi® Video
(v3.8 or above) controller software. The software may be
hosted on either of the following:
• The Ubiquiti Networks® UniFiNVR appliance
• A Linux/Windows computer
Note: The latest UniFi Video software is available for free
download at: www.ubnt.com/download/unifivideo
The UVC G3 Micro can be powered by either of the following
methods:
• Using the included Instant PoE Adapter connected to an
802.3af PoE-compliant switch
• Using the included Power Adapter

Hardware Overview
LED Reset
Magnetic
Base
LED The LED will flash blue during bootup. When the camera
is ready to connect to the Wi-Fi network, the LED pattern
will flash two times accompanied by two beep tones. Once
connected to the network, the LED will glow a breathing
pattern.
State Status
Flashing Blue Device is Booting Up
Steady Blue Connected to NVR
Flashing White Connecting to Wi-Fi
Steady White Ready for Configuration
Flashing Red Cannot Connect to NVR
Steady Red No Wi-Fi Connection
Reset To reset network settings to factory defaults, press and
hold the Reset button until the camera emits two fast tones.

Installation
The UVC G3 Micro can be mounted in four ways:
• Magnetic For temporary installation
• Adhesive For fast, permanent installation
• Screws For secure installation
• Table For installing on a flat surface such as a table or shelf
Magnetic Mount
1. Remove the Wall Mount from the Magnetic Base.
Wall Mount
2. Attach the Power Adapter or Instant PoE Adapter to the
MagneticBase.

3. Attach the camera and Magnetic Base directly to a metal
fixture. Go to Connecting the Power .
Adhesive Mount
1. If the Power Adapter cord or PoE Adapter Cord feeds through
the wall, drill or cut a hole and feed the cord through it.
2. Remove the tab from the notch and attach the Wall Mount
using the adhesive side.
*640-00321-01*
640-00321-01

3. Attach the Power Adapter or Instant PoE Adapter to the
MagneticBase.
4. Attach the camera and Magnetic Base to the mount. If
the power cord feeds through the Wall Mount, rotate the
Magnetic Base to align the cord with the notch on the Wall
Mount.Go to Connecting the Power.
Cord on Wall Cord Through Wall Mount

Screw Mount
1. If the circular connector on the Power Adapter or Instant PoE
Adapter needs to connect through the wall, drill or cut a
hole out and feed the power connector through it.
Wall Mount Angle Mount
2. Use the Screws and Screw Anchors to fasten the Wall Mount
or the Angle Mount.
Wall Mount
Angle Mount

3. Attach the Power Adapter to the Magnetic Base.
4. Attach the camera and Magnetic Base to the mount. If
the power cord feeds through the Wall Mount, rotate the
Magnetic Base so the cord aligns with the notch on the Wall
Mount. Go to Connecting the Power.
Cord on Wall Cord Through Wall Mount

Table Mount
1. Feed the circular power connector (on the Power Adapter or
Instant PoE Adapter) through the hole in the Table Stand.
2. Attach the circular power connector to the Magnetic Base
of the camera.
3. Attach the Magnetic Base of the camera to the Table Stand by
pressing it over the two notches and sliding it down.

Connecting the Power
Follow the instructions for your method of powering the
camera: Power Adapter or Instant PoE Adapter.
Power Adapter
Plug the Power Adapter into an outlet.
Note: Use the included Cable Clips to hold the power
cord in place. Remove the paper backing on each clip to
expose the adhesive and affix to a desired location.
Instant PoE Adapter
1. Install the Instant PoE Mount on a wall using the included
screw kit.
Securing the Instant PoE Wall Mount Instant PoE Wall Mount Installed

2. Attach the circular power connector to the Magnetic Base
of the camera.
3. Attach the Magnetic Base of the camera to the Instant PoE
Mount by pressing it over the two notches and sliding it down.
4. Place the Instant PoE Cover over the Magnetic Base and onto
the Instant PoE Wall Mount until it snaps into place. Then
mount the camera to the Magnetic Base.
Attach Instant PoE Cover Mount Camera to Magnetic Base

5. Connect the Ethernet cable from an 802.3af PoE switch to
the PoE In port of the Instant PoE Adapter.
Note: Use the included Cable Clips to hold the power
cord in place. Remove the paper backing on each clip to
expose the adhesive and affix to a desired location.
Setting Up the UVC G3 Micro
Ensure you are running the latest version of UniFi Video, v3.8 or
above on the UniFi NVR or computer-based system.
Download the UniFi Video User Guide for detailed information
on how to set up and use UniFi Video:
www.ubnt.com/download/unifivideo
UniFi Video Mobile App
For quick setup, a mobile app is available. Install the UniFi Video
app, and follow the on-screen instructions:
• iOS: iTunes App Store
• Android: Google Play™ Store

Specifications
UVC-G3-Micro
Dimensions
Body
Base
Ø 51.38 x 41.97 mm (2.02 x 1.65")
Ø 36.0 x 17.3 mm (1.41 x 0.68”)
Weight
Body
Base
65 g (2.29 oz)
31 g (1.09 oz)
Enclosure Characteristics White Body with Black Front Surface
Mounting Options Magnetic Base, Wall Mount, or Table Mount
Networking Interface 802.11 a/b/g/n Dual-Band Wi-Fi; BT
Lens 2.7 mm f2.2
Sensor 1/3"4MP Image Sensor with WDR
View Angle
LDC Off
LDC On
124° (H), 65° (V), 150° (D)
92° (H), 6° (V), 100° (D)
Night Mode Infrared LEDs with
Built-In Light Sensor
Video Compression H.264
Resolution 1080p HD (1920 x 1080)
Max. Frame Rate 30 FPS
Microphone Yes (with Volume Control)
Speaker Yes
Power Supply AC Adapter or Instant PoE Adapter
Supported Voltage Range 5V (4.85V - 5.35V)
Max. Power Consumption
IR LEDs On
IR LEDs Off
3.5W
2W
Operating Temperature 0 to 35° C (32 to 95° F)
Operating Humidity 20 to 90% Noncondensing
Certications CE, FCC, IC

Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.
WARNING: Do not use this product in location that can
be submerged by water.
WARNING: Avoid using this product during an electrical
storm. There may be a remote risk of electric shock from
lightning.
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current
requirements indicated on the manufacturer’s label. Connection to a
different power source than those specified may result in improper
operation, damage to the equipment or pose a fire hazard if the
limitations are not followed.
2. There are no operator serviceable parts inside this equipment. Service
should be provided only by a qualified service technician.
3. This equipment is provided with a detachable power cord which has
an integral safety ground wire intended for connection to a grounded
safety outlet.
a. Do not substitute the power cord with one that is not the provided
approved type. Never use an adapter plug to connect to a 2-wire
outlet as this will defeat the continuity of the grounding wire.
b. The equipment requires the use of the ground wire as a part of the
safety certification, modification or misuse can provide a shock
hazard that can result in serious injury or death.
c. Contact a qualified electrician or the manufacturer if there
are questions about the installation prior to connecting the
equipment.
d. Protective earthing is provided by Listed AC adapter. Building
installation shall provide appropriate short-circuit backup
protection.
e. Protective bonding must be installed in accordance with local
national wiring rules and regulations.

Limited Warranty
UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) warrants that the
product(s) furnished hereunder (the “Product(s)”) shall be free from defects
in material and workmanship for a period of one (1) year from the date
of shipment by UBIQUITI NETWORKS under normal use and operation.
UBIQUITI NETWORKS’ sole and exclusive obligation and liability under
the foregoing warranty shall be for UBIQUITI NETWORKS, at its discretion,
to repair or replace any Product that fails to conform to the above
warranty during the above warranty period. The expense of removal and
reinstallation of any Product is not included in this warranty. The warranty
period of any repaired or replaced Product shall not extend beyond its
original term.
Warranty Conditions
The above warranty does not apply if the Product:
(I) has been modified and/or altered, or an addition made thereto,
except by Ubiquiti Networks, or Ubiquiti Networks’ authorized
representatives, or as approved by Ubiquiti Networks in writing;
(II) has been painted, rebranded or physically modified in any way;
(III) has been damaged due to errors or defects in cabling;
(IV) has been subjected to misuse, abuse, negligence, abnormal physical,
electromagnetic or electrical stress, including lightning strikes, or
accident;
(V) has been damaged or impaired as a result of using third party
firmware;
(VI) has no original Ubiquiti MAC label, or is missing any other original
Ubiquiti label(s); or
(VII) has not been received by Ubiquiti within 30 days of issuance of
the RMA.
In addition, the above warranty shall apply only if: the product has been
properly installed and used at all times in accordance, and in all material
respects, with the applicable Product documentation; all Ethernet cabling
runs use CAT5 (or above), and for outdoor installations, shielded Ethernet
cabling is used, and for indoor installations, indoor cabling requirements
are followed.

Returns
No Products will be accepted for replacement or repair without obtaining
a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS
during the warranty period, and the Products being received at UBIQUITI
NETWORKS’ facility freight prepaid in accordance with the RMA process of
UBIQUITI NETWORKS. Products returned without an RMA number will not
be processed and will be returned freight collect or subject to disposal.
Information on the RMA process and obtaining an RMA number can be
found at: www.ubnt.com/support/warranty
Disclaimer
EXCEPT FOR ANY EXPRESS WARRANTIES PROVIDED HEREIN, UBIQUITI
NETWORKS, ITS AFFILIATES, AND ITS AND THEIR THIRD PARTY DATA,
SERVICE, SOFTWARE AND HARDWARE PROVIDERS HEREBY DISCLAIM
AND MAKE NO OTHER REPRESENTATION OR WARRANTY OF ANY KIND,
EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT NOT LIMITED TO,
REPRESENTATIONS, GUARANTEES, OR WARRANTIES OF MERCHANTABILITY,
ACCURACY, QUALITY OF SERVICE OR RESULTS, AVAILABILITY,
SATISFACTORY QUALITY, LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS
FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT AND ANY
WARRANTIES ARISING FROM ANY COURSE OF DEALING, USAGE OR
TRADE PRACTICE IN CONNECTION WITH SUCH PRODUCTS AND SERVICES.
BUYER ACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKS NOR
ITS THIRD PARTY PROVIDERS CONTROL BUYER’S EQUIPMENT OR THE
TRANSFER OF DATA OVER COMMUNICATIONS FACILITIES, INCLUDING
THE INTERNET, AND THAT THE PRODUCTS AND SERVICES MAY BE
SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS
AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS
FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD
PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS,
DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT
CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY
OF THE FOREGOING. In addition, UBIQUITI NETWORKS does not warrant
that the operation of the Products will be error-free or that operation will
be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible
for damages or claims of any nature or description relating to system
performance, including coverage, buyer’s selection of products (including
the Products) for buyer’s application and/or failure of products (including
the Products) to meet government or regulatory requirements.

Limitation of Liability
EXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW, IN NO EVENT WILL
UBIQUITI OR ITS SUBSIDIARIES, AFFILIATES OR SUPPLIERS BE LIABLE FOR
DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHER DAMAGES
(INCLUDING LOST PROFIT, LOST DATA, OR DOWNTIME COSTS), ARISING
OUT OF THE USE, INABILITY TO USE, OR THE RESULTS OF USE OF THE
PRODUCT, WHETHER BASED IN WARRANTY, CONTRACT, TORT OR OTHER
LEGAL THEORY, AND WHETHER OR NOT ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
Note
Some countries, states and provinces do not allow exclusions of implied
warranties or conditions, so the above exclusion may not apply to you.
You may have other rights that vary from country to country, state to
state, or province to province. Some countries, states and provinces do not
allow the exclusion or limitation of liability for incidental or consequential
damages, so the above limitation may not apply to you. EXCEPT TO
THE EXTENT ALLOWED BY LOCAL LAW, THESE WARRANTY TERMS DO
NOT EXCLUDE, RESTRICT OR MODIFY, AND ARE IN ADDITION TO, THE
MANDATORY STATUTORY RIGHTS APPLICABLE TO THE LICENSE OF ANY
SOFTWARE (EMBEDDED IN THE PRODUCT) TO YOU. The United Nations
Convention on Contracts for the International Sale of Goods shall not apply
to any transactions regarding the sale of the Products.
Compliance
FCC
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions.
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This radio transmitter FCC ID: SWX-UVCG3M has been approved by FCC.
Industry Canada
CAN ICES-3(B)/NMB-3(B)
This Class B digital apparatus complies with Canadian CAN ICES-003.
To reduce potential radio interference to other users, the antenna
type and its gain should be so chosen that the equivalent isotropically
radiated power (e.i.r.p.) is not more than that permitted for successful
communication.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that
may cause undesired operation of the device.
This radio transmitter (IC: 6545A-UVCG3M) has been approved by Industry
Canada.
CAN ICES-3(B)/NMB-3(B)
Cet appareil numérique de la classe B est conforme à la norme NMB-003
du Canada.
Pour réduire le risque d’interférence aux autres utilisateurs, le type
d’antenne et son gain doivent être choisies de façon que la puissance
isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire
pour une communication réussie.
Cet appareil est conforme à la norme RSS Industrie Canada exempts de
licence norme(s). Son fonctionnement est soumis aux deux conditions
suivantes:
1. Cet appareil ne peut pas provoquer d’interférences et
2. Cet appareil doit accepter toute interférence, y compris les
interférences qui peuvent causer un mauvais fonctionnement du
dispositif.
Cet émetteur radio (IC: 6545A-UVCG3M) a été approuvée par Industrie
Canada.

RF Exposure Warning
The antennas used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be
located or operating in conjunction with any other antenna or transmitter.
Les antennes utilisées pour ce transmetteur doivent être installé en
considérant une distance de séparation de toute personnes d’au moins
20 cm et ne doivent pas être localisé ou utilisé en conflit avec tout autre
antenne ou transmetteur.
CE Marking
CE marking on this product represents the product is in compliance with all
directives that are applicable to it.