Ubiquiti UniFi G3 PRO User manual

1080p Indoor/Outdoor
IP Camera with Infrared
and Optical Zoom
Model: UVC-G3-PRO
Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Ubiquiti Networks G3-PRO o cerca il
tuo prodotto tra le migliori offerte di Videosorveglianza

Introduction
Thank you for purchasing the Ubiquiti
Networks® UniFi Video® G3 Pro Camera.
This Quick Start Guide is designed to guide
you through installation and also includes
warranty terms.
Package Contents
UVC-G3-PRO Tightening Tool
Screw Anchors
(Qty. 2)
Self-Tapping Screws
(Qty. 2)
1080pIndoor/Outdoor
IPCamera with Infrared
andOptical Zoom
Model:UVC-G3-PRO
Pole Mount
Bracket
Machine Screws
(Qty. 2)
Quick Start
Guide

Installation Requirements
• Pole-mounting: Two metal straps (not
included)
• Shielded Category 5 (or above) cabling with
drain wire should be used for all outdoor
wired Ethernet connections and should
be grounded through the AC ground of
the PoE.
We recommend that you protect
your networks from harmful outdoor
environments and destructive ESD events
with industrial-grade, shielded Ethernet
cable from Ubiquiti Networks. For more
details, visit www.ubnt.com/toughcable
• Surge protection should be used for all
outdoor installations. We recommend that
you use two Ethernet Surge Protectors,
model ETH-SP, one near the camera and the
other at the entry point to the building. The
ETH-SP will absorb power surges and safely
discharge them into the ground.

To LAN
ETH-SP
ETH-SP
US-8-150W
UVC-G3-PRO
Diagram Showing Use of Ethernet Surge Protectors
TERMS OF USE: All Ethernet cabling runs must use CAT5 (or
above). Shielded Ethernet cable and earth grounding must
be used for outdoor installations as conditions of product
warranty. TOUGHCable™ is designed for outdoor installations. It
is the professional installer’s responsibility to follow local country
regulations.

Hardware Overview
48V 0.5A PoE
M/N:UVC-G3-PRO
Compliant
RoHS
RESET
Mounting Base
Cable Gland
Tilt/Mount Ring
Adjustable Base
Camera
Ring
Camera Lens
Ambient Light Sensor
Reset Button
Ethernet Port
Microphone
Cable Slot

Ethernet 10/100 RJ45 port connects to an
802.3af/802.3at PoE switch for PoE power
and data.
Reset Button To reset to factory defaults,
press and hold the Reset button for more than
10 seconds while the camera is poweredon.
Before You Begin
Remove the sticker from the bottom of the
Mounting Base.
Installation Overview
To install the camera, please follow the
instructions of the following sections in this
order:
1. Hardware Installation
2. Connecting Power over Ethernet
3. UniFi Video
4. Adjusting the Camera View
Hardware Installation
The camera can be mounted on a wall, ceiling,
or pole. Follow the appropriate steps for your
installation:

Wall/Ceiling Mount
1. Remove the Mounting Base from the
camera by turning the Tilt/Mount Ring
counterclockwise.
2. Mark the mounting holes on the wall or
ceiling.

Note: If you are running the cable along
the wall or ceiling, position the Cable
Slot towards the direction you want the
cabling to run. For outdoor installations,
position the Cable Slot downward.
3. Use a 7 mm (¼") drill bit to drill the
mounting holes in the wall or ceiling.
Note: If you are running the Ethernet
cable through the wall, cut a hole
centered between the mounting
holes that is large enough to feed the
cable through.
4. Insert a Screw Anchor into each mounting
hole.

5. If you are feeding the Ethernet cable
through the wall or ceiling, do so now and
feed it through the Mounting Base.
If not, feed the Ethernet cable through the
Mounting Base and place the cable in the
Cable Slot.

IMPORTANT: If you are installing your
camera outdoors, create a drip loop for
the cable below the camera to prevent
water ingress.
6. Fasten the Mounting Base to the wall or
ceiling using two Self-Tapping Screws.
7. Remove the camera from the Adjustable
Base by turning the Camera Ring in the
direction shown.

8. Remove the Cable Gland from the
Adjustable Base.
9. Feed the Ethernet cable through the Cable
Gland and Adjustable Base. Seal the Cable
Gland in place by firmly pressing around
its edges. Then connect the cable to the
Ethernet Port on the camera.
48V 0.5A PoE
M/N:UVC-G3-PRO
Compliant
RoHS
RESET

IMPORTANT: For proper weather sealing,
the Cable Gland must fit securely within
the Adjustable Base when the camera is
mounted. Ensure that the Cable Gland is
securely seated during installation and
cable routing.
10. Connect the camera back to the Adjustable
Base by turning the Camera Ring in the
direction shown.

11. Orient the camera to the desired position
while connecting the Adjustable Base to
the Mounting Base.
Note: You will fine-tune and then
lock the positioning after you check
the camera view in the UniFi Video
software.
12. Proceed to the Connecting Power over
Ethernet section.

Pole Mount
To mount the camera on a pole, two metal
straps are required (not included).
1. Feed the metal straps through the slots on
the Pole Mount Bracket.
2. Wrap a metal strap around the pole and
tighten it by turning the screw clockwise.
Repeat for the second strap.

3. Remove the Mounting Base from the
camera by turning the Tilt/Mount Ring
counterclockwise.
4. Feed the Ethernet cable through the
Mounting Base.

5. Fasten the Mounting Base to the Pole
Mount Bracket using two Machine Screws.
6. Remove the camera from the Adjustable
Base by turning the Camera Ring in the
direction shown.

7. Remove the Cable Gland from the
Adjustable Base.
8. Feed the Ethernet cable through the Cable
Gland and Adjustable Base. Seal the Cable
Gland in place by firmly pressing around
its edges. Then connect the cable to the
Ethernet Port on the camera.
48V 0.5A PoE
M/N:UVC-G3-PRO
Compliant
RoHS
RESET

IMPORTANT: For proper weather sealing,
the Cable Gland must fit securely within
the Adjustable Base when the camera is
mounted. Ensure that the Cable Gland is
securely seated during installation and
cable routing.
9. Connect the camera back to the Adjustable
Base by turning the Camera Ring in the
direction shown.

10. Orient the camera to the desired position
while connecting the Adjustable Base to
the Mounting Base.
Note: Fine-tune and then lock the
positioning after you check the camera
view in the UniFi Video software.

Connecting Power over Ethernet
The camera features auto-sensing
802.3af/802.3at PoE and can be powered by
any 802.3af/802.3at PoE compliant switch,
such as a UniFi PoE Switch.
Connect the Ethernet cable from the camera
directly to a PoE port on the switch.
1 3 5 7 9 11 13 15 17 19 21 22
2 4 6 8 10 12 14 16 18 20 22 24
1 3 5 7 9 11 13 15 17 19 21 22
2 4 6 8 10 12 14 16 18 20 22 24
SFP1
SFP2
*640-00316-06*
640-00316-06