Uconnect WA-232E User manual

User Manual V1.3 Date: 2017.06.03
1
WiFi to RS-232 adapter user manual
WiFi to RS-232 adapter
White Box Dimension: 11 x 6 x 5 (cm)
Total Package Weight: 126 g
Package Contents:
WiFi RS-232 adapter x 1
2 dBi dipole antenna x 1
A4 User manual x 1
USB Cable x 1
1. Product profile: Female DB9 connector with nut (The nut can be removed if necessary.)
2. Start to use the adapter
2.1 Please fasten the external antenna to the adapter.
2.2 There’re three power inputs, mini USB, pin9 of DB9 or blue 2 ports block terminal. Please select
one way to power the adapter. The max. voltage is 27 VDC input for all sources.
2.3 COM port default setting:
Baud rate: x, 9,600 bps
Data bit: 8
Parity: none
Stop bit: 1
Flow control: none
DB9 (Female)
LED:
Data: Red
Status: Blue
DCE/DTE
2 dBi dipole
antenna
Mini USB
Power switch
5 ~27VDC
GND
+
Reset switch
DB9 Female connector
with screw nut

User Manual V1.3 Date: 2017.06.03
2
2.4Network default setting:
Simple AP and support DHCP
SSID: Serial2WiFi_ab_cd (ab or cd means the last 4 code of the Mac. address)
No Security
IP: 192.168.0.3
Socket port: 5000
Channel: 11
Log in ID: admin
Log in password: admin
2.5 Power switch: mini USB side by default. The user will switch to the blue 2 ports block terminal
side or pin9 of DB9 if the power input comes from other sources.
2.6 DCE/DTE switch: DCE side. The switch will swap TX,RX,CTS,RTS of the COM port. Generally,
DCE side for PC or NB setup. The user will test and switch to the correct side for the remote
device.
3. Configuration: Please choose one way and download the “TeraTerm” tool for testing.
3.1 Web page: The user will setup the adapter via PC, NB or Smart phone.
You can configure the WiFi and COM port parameters from the web page. Please press “Apply”
when setup and the adapter will reboot.
3.2 PC software:
Step1: Please connect the simpleAP named “Serial2WiFi_ab_cd”
Step2: Execute AXR2W Configuration Utility with the administrator authority.
Step3: Search the WiFi device, double click the item and the setup page display.
Step1: Connect the simpleAP named
“Serial2WiFi_ab_cd”
Step2: http://192.168.0.3 on browser
Step3: Log in
Username: admin
Password: admin
Double click
Search
Please check the right network

User Manual V1.3 Date: 2017.06.03
3
Network setting Serial port setting WiFi setting DHCP Server Setting
3.3 RS-232:
4. Virtual COM port driver: Execute the utility by "Administrator" authority.
Step1: Connect the adapter via WiFi
and connect the RS-232
connector
Step2: Execute COM port tool software
Step3: Set baud rate: 115200 bps
Step4: Key in “+++” and then Enter
Step5: Log in the device and setup

User Manual V1.3 Date: 2017.06.03
4
5. LED indication:
5.1 Red: Power On or Off
5.2 Blue: Wifi Status
6. Reset button:
Press the “Reset” button over 5 seconds, the WiFi adapter will reset to default value. The LEDs will
be off for some time and then reboot to the default value. The function is the same ad the software
reset.
7. RS232 Interface: DB9 Female with Nut
7.1 Pin-out:
Drag the device to the
Virtual COM ports
Please disable Flow
Control function.

User Manual V1.3 Date: 2017.06.03
5
7.2 Signals:
Pin Signal DTE Direction DCE Direction Description
1 CD Input Output Not connected
2 TxD Output Input Transmitted data
3 RxD Input Output Received data
4 DSR Input Output Contact manufacturer to set this
5 GND N/A N/A Signal ground
6 DTR Output Input Contact manufacturer to set this
7 CTS Input Output Clear to send
8 RTS Output Input Request to send (Default)
9 Vcc Input Input External Power supply
Remark: DSR/DTR Connection:
8. Command set:
Usage: ipconfig
Usage: setip <IP address>
Usage: setnetmask <netmask>
Usage: setgateway <gateway IP address>
Usage: setdns <DNS IP address>
Usage: setmode <mode>
<mode>: 0: SERVER 1: CLIENT
Usage: r2wmode <mode>
<mode>
0: Socket
1: VCOM
2: RFC2217
3: Modbus Gateway
Usage: setsrvport <port number>
Usage: setdstport <port number>
Usage: setdsthn <host name | IP address>
Usage: connectype <protocol>
<protocol>: 0: TCP 1: UDP
Usage: connstatus
Usage: wifi_connect [SSID] [WPA PASSWORD / WEP KEY(5 or 13)] [WEP KEY ID]
SSID = 1 ~ 32 ASCII characters
WPA PASSWORD = 8 ~ 63 ASCII characters
ASCII WEP KEY = 5 (WEP64) or 13 (WEP128) ASCII characters
WEP KEY ID = 0 ~ 3
Usage: wifi_disconnect
Usage: wifi_mode [MODE]
MODE = 1(STA), 2(AP)
Usage: wifi_scan
Usage: wifi_jbss <INDEX>

User Manual V1.3 Date: 2017.06.03
6
INDEX = Index of bss scan table, maximum 24 BSSs supported
Usage: wifi_on
Usage: wifi_off
Usage: wifi_channel <CHANNEL>
CHANNEL = 1 ~ 13
Usage: wifi_ssid <SSID>
SSID = 1 ~ 32 ASCII characters
Usage: wifi_enc <ENC_MODE>
ENC_MODE = 0(OPEN)
1(WEP)(AP mode not support)
2(WPA2_AES_PSK)
Usage: wifi_keyid <INDEX>
INDEX = 0 ~ 3
Usage: wifi_wepkey <INDEX> <KEY>
INDEX = 0 ~ 3
KEY = 5 or 13 ASCII characters
Usage: wifi_wpakey <KEY>
KEY = 8 ~ 63 ASCII characters
Usage: reboot
Usage: urdatamode
Usage: setdef
Usage: saveconfig
Usage: ping <IP address>
Usage: wifi_info
Usage: wifi_ap <ssid> <channel> <wep/wpa key> <wep key index>
<ssid>: 1~32 ASCII characters
<channel>: 1~14
<wep/wpa key>: WEP(5/13 ASCII characters) or WPA(8~63 ASCII characters) k
ey
<wep key index>: WEP key index, 0~3
Usage: ur_config <baud_rate> <databits> <stop_bits> <parity> <flow_contrl>
<baud_rate>:
1200 bps
2400 bps
4800 bps
9600 bps
19200 bps
38400 bps
57600 bps
115200 bps
921600 bps
<databits>: 7 or 8 bits
<stop_bits>: 1 or 2 bit(s)
<parity>: 0 = none, 1 = odd, 2 = even
<flow_contrl>: 0 = disable, 1 = enable CTS/RTS flow control
Usage: dhcpclient <status>
<status>: 0: disable 1: enable
Usage: setdhcpsrv <status>
<status>: 0: disable 1: enable
Usage: ntpsrv <time zone> <ntp server1> <ntp server2> <ntp server3>
<time zone>
0: GMT-12.0 Eniwetok, Kwajalein
1: GMT-11.0 Midway Is., Samoa
2: GMT-10.0 Hawaii
3: GMT-9.0 Alaska

User Manual V1.3 Date: 2017.06.03
7
4: GMT-8.0 Los Angeles, Tijuana
5: GMT-7.0 Denver Arizona
6: GMT-6.0 Chicago, Mexico City
7: GMT-5.0 New York, Bogota
8: GMT-4.0 Santiago
9: GMT-3.0 Brasilia, Montevideo
10: GMT-2.0 Fernando de Noronha
11: GMT-1.0 Azores
12: GMT+0.0 Lisbon, London
13: GMT+1.0 Berlin, Paris
14: GMT+2.0 Helsinki, Cairo
15: GMT+3.0 Moscow, Nairobi
16: GMT+4.0 Abu Dhabi, Baku
17: GMT+5.0 Karachi, Islamabad
18: GMT+6.0 Almaty, Dhaka
19: GMT+7.0 Bangkok, Jakarta
20: GMT+8.0 Hong Kong, Singapore
21: GMT+9.0 Seoul, Tokyo
22: GMT+10.0 Melbourne, Sydney
23: GMT+11.0 Solomon Is.
24: GMT+12.0 Fiji, Wellington
Usage: rtcts <mode>
<mode>: 0: manual 1: NTP server
Usage: time <hour> <minute> <second>
<hour>: 0~23
<minute>: 0~59
<second>: 0~59
Usage: date <year> <month> <date>
<year>: 2000~2099
<month>: 1~12
<date>: 1~31
Usage: getths
Usage: setems <e-mail server domain name>
Usage: setemf <e-mail address>
Usage: setemt1 <e-mail address>
Usage: setemt2 <e-mail address>
Usage: setemt3 <e-mail address>
Usage: setemsc <SecurityType> <PortNumber>
<SecurityType>:
0=No security
1=SSL
2=TLS
3=Auto
<PortNumber>:
25 or 587 for regular transfer port
465 for SSL port
Usage: setemac <UserName> <PassWord>
Usage: emconfig
Usage: setaw <cold start> <authentication fail> <ip changed> <password changed>
<cold start>: 0: Disable 1: Enable
<authentication fail>: 0: Disable 1: Enable
<ip changed>: 0: Disable 1: Enable
<password changed>: 0: Disable 1: Enable

User Manual V1.3 Date: 2017.06.03
8
Usage: jtagoff <status>
<status>: 0: enable 1: disable
Usage: getotaname
Usage: countryid <id>
<id>:
0=World wide 13(2G_WORLD: 1~13)
1=Europe(2G_ETSI1: 1~13)
2=Japan(2G_MKK1: 1~14)
20=United States(2G_FCC2: 1~13)
Otherwise=Unavailable
Usage: dhcpsrv <start addr> <end addr> <lease>
Usage: transmitimer <time>
<time>: time in ms, available value range is 10~65535 ms
Usage: dhcpstbl
Usage: scpincode <status>
<status>: 0: disable 1: enable
Usage: cloud <hostname>
Usage: mbtcp <xferMode> <port>
<xferMode>: 0: MODBUS TCP 1: Transparent TCP
<port>: TCP server port number, default is 502
Usage: mbst <ResponseTimeOut> <InterFrameDelay> <InterCharDelay>
<ResponseTimeOut>: Response timeout(10~65000ms)
<InterFrameDelay>: Interval time of frame sending(10~500ms)
<InterCharDelay>: Inter-Character timeout for frame receiving(10~500ms)
Usage: wifi_simple_config <pinCode>
9. Online help: “help” command (Available for RS-232 setup only)
10. One to one connection: The two WiFi adapters will be connected directly without access point.
Simple AP Station mode
TCP Server TCP Client (Host IP is the
same as the TCP server)
11. Test APP Download: If you need the sample code, please contact the supplier.
iOS Android
Connect directly
Max.
4
clients