UDIZINE Palo System IPSK002 User manual

Palo System Installation Instructions
General Note: It is the responsibility of the purchaser and/or installer to verify that the mounting surface is solid and capable of supporting the intended
weight of display. It is recommended to consult with a professional and determine the appropriate fastener/anchor needed for the mounting surface. UDIZINE
is solely responsible for the quality of its products and not accountable for faulty installation and ill use of its products beyond recommended limitations.
IPSK002
Hang Rail Kit - Ø 2.5 cm (1”)
Page 1 of 3
Wall to Floor - Hang Rail
G
H
H
H
H2
H1
PSK-S01 - 60cm (24”)
PSK-S02 - 90cm (36”)
PS110AN - 60cm (24”)
PS111AN - 90cm (36”)
Wall Kit Fixtures
Toggle Bolts Molly Bolts
Level
4.8mm (3/16”)Phillips Screw Driver
Hand Saw
Metric #2.5 & #3
Please Note:
For mounting on sheet rock/drywall,
we recommend using 4.8mm (3/16”)
Molly bolts or Toggle bolts.
FYI: Tools and mounting hardware
are not provided
Recommended Tools:
PS15AN
A
E
C
B
PS13AN
PSK-F01 - 20cm (8”)
PSK-F02 - 30cm (12”)
PS11AN
FPS12AN
D
PS14AN
Max Height:
244cm (96”)
Can be cut to size
Max Weight Load:
Per Setting : 240kg (530lbs)
Per Bar:
PSK-S02 -76cm (36”)
PSK-S01 - 61cm (24”)
AS12AN - 20cm (8”)
AS13AN - 30cm (12”)
PS19AN
PSK-S01 - 60cm (24”)
PSK-S02 - 90cm (36”)
Dispersed Load
37kg (81lbs)
25kg (55lbs)
Concentrated Load
45kg (99lbs)
30kg (66lbs)
PSK-F01 PSK-F02
20cm (8”) 30cm (12”)

Palo System Installation Instructions
General Note: It is the responsibility of the purchaser and/or installer to verify that the mounting surface is solid and capable of supporting the intended
weight of display. It is recommended to consult with a professional and determine the appropriate fastener/anchor needed for the mounting surface. UDIZINE
is solely responsible for the quality of its products and not accountable for faulty installation and ill use of its products beyond recommended limitations.
IPSK002
Page 2 of 3
Wall to Floor - Hang Rail
Before setting the next pole, mark on
the wall the distance between the 2
poles, based on the length of the shelves
(L) + 5cm (2”)
8
L+5cm (2”)
Stage 1 : Pole Installation
5 7
Above 180cm (71”)
requires 2 wall supports
Up to 180cm (71”)
requires 1 wall support
20cm (8”)
4
Position the pole
near the wall. Adjust
pole horizontally and
vertically using level.
Mark attachment point
for Parts B and F
Drill holes at marked points
using the appropriate
hardware for the type of
wall/oor.
Mount Parts B and F at
the marked points
Place pole in to Parts
B and F and adjust
pole horizontally and
vertically using level.
Tighten with Allen key
5 6 7
E
B
C
F
E
E
B
A
F
Attach Part D with
screw 4.8mm (3/16”)
to the back mark line
2
D
D
C
Insert Part C into Part D
and tighten Allen screw
3
C
Cut the pole to the
required length.
Assemble cap to top
of pole
Determine how many wall supports are
needed based on the height of the setting
1
H
Insert part B into
Part C. Insert Part F
into Part E. DO NOT
TIGHTEN YET!
B
F
120cm (48”) 20cm (8”)
B
F
20cm (8”)
L+5cm (2”)
L

Palo System Installation Instructions
General Note: It is the responsibility of the purchaser and/or installer to verify that the mounting surface is solid and capable of supporting the intended
weight of display. It is recommended to consult with a professional and determine the appropriate fastener/anchor needed for the mounting surface. UDIZINE
is solely responsible for the quality of its products and not accountable for faulty installation and ill use of its products beyond recommended limitations.
IPSK002
H
H1
Attach Part H at required
height on one side
Lock in place by turning the Allen screw to secure
horizontally and tighten with Allen key
Insert Part G into H on rst pole.
Insert Part H1 to second pole as shown in steps 1 and 2
Slide H2 to Part G Attach Part H2 to H1 and adjust until level.
While holding Part G, separate part H1
from H2 from second Pole
1
3 4 5
6
2
Stage 2 : Adding Hang Rail
G
GG
G
G G
G

Wall to Floor - Hang Rail
G
H
H H
H2
H2
H2 H1
H1
Fixed
H2
H2
H1
H1
Tighten Part H1 to second pole with
Allen key
7
H
H
H2
H1
Tighten both Parts H with Allen key
8
G
Attach Part H2 to H1 and tighten
7
To add additional sections repeat
Stages 1 and 2
Page 3 of 3
H1
Fixed