UEi ECT600A User manual

1-800-547-5740 • Fax: [phone]
www.ueitest.com • email: [email protected]
ECT600A
INSTRUCTION MANUAL

International Symbols
C o n t r ols and Indicators
DANGER!
DO NOT exceed 700 volts AC or DC. Exceeding this value may result in
serious injury or equipment damage!
DANGER!
Voltage measured from phase to phase may be much higher than the
specified voltage. Some multi-phase systems are specified relative to
the voltage measured from ground to a single phase.
DANGER!
DO NOT remove the ECT600A from its protective boot or use when
wet. The boot provides insulation from measured voltage. Moisture
reduces insulation’s properties.
WARNING!
Inspect this instrument prior to use for cracks ordamage to the housing,
frayed or cut insulation, modification, or any other discre p a n cy to the unit.
DO NOT use your ECT600A if any of these conditions exist! Replace the
instrument or have it re paired at a qualified facility.
WARNING!
Probe tips are extremely sharp! Store and transport this instrument in
a manner that reduces risk of contact with the probes tips. DO NOT
attempt to catch the unit if it is dropped.
Verify your instrument is functioning properly: Each time you
use your ECT600A, verify it is functioning properly by following the
instructions below on a know good voltage source. This is particularly
important when using this instrument to ensure wiring is safe to touch.
Introduction
The ECT600A detects both voltage and continuity. The bright panel of
Light Emitting Diode (LED) indicators provides a quick and sure display of
measured voltage, ranging from 12 to 600 volts AC or DC. A loud, clear
audio tone sounds to give you a quick indication that voltage or continuity
is present even if you can’t see the display.
The continuity feature sounds at a distinctive tone when the ECT600A finds
a path for current to flow between two wires or other probed points.
With no batteries to replace, your ECT600A is ready to go when youare.
Features include
• Quick single-probe AC checks
• LED indication of voltage level
• Loud audible tone
• Continuity tester
• AC and DC voltage measurement
• No battery needed
Safety Notes
Before using this meter, read all safety information carefully. In
this manual the word "WARNING" is used to indicate conditions
or actions that may pose physical hazards to the user. The word
"CAUTION" is used to indicate conditions or actions that may
damage this instrument.
WARNING!
Exceeding the specified limits of this meter is dangerous and can
expose the user to serious or possibly fatal injury.
•Read the safety precautions associated with the equipment being
tested and seek assistance or advice when performing
unfamiliar tasks.
• Keep your fingers away from the test lead metal probe contacts
and bus-bars when making measurements. Always grip the
instrument and test-lead behind the hand guards (molded into
the probe).
•In the event of electrical shock, ALWAYS bring the victim to
the emergency room for evaluation, regardless of the victim’s
apparent recovery. Electrical shock can cause an unstable heart
rhythm that may need medical attention.
ECT600A-MAN P. 1

This does not indicate a problem with the instrument. To avoid tripping
a breaker, initially charge this instrument on a circuit with a 20 amp or
more breaker, without ground-fault isolation.
Your ECT600A will test both AC and DC voltage, ranging from
approximately 12 to 600 volts.
When AC voltage (up to 60 cycles) is detected, both of the bottom two
LEDs will light while a warbling audible tone sounds. When working
with both probes on AC voltage, the probes can be used on either the
hot wire or the return wire, without regard to polarity.
When DC voltage is detected only one of the bottom two LEDs will light.
That light corresponds to the polarity of the voltage at the probes. The
probe attached to the body of the instrument is the positive probe and the
probe at the end of the black test lead is the negative or “ground” probe.
Single Probe Quick Tests On Hot-Wires
Allow your instrument’s internal power supply to charge by testing
for voltage, leaving the unit exposed to the AC signal source for at
least 5 seconds.
After the unit is fully charged, you can detect AC voltages in excess of
100 volts by simply placing the body’s test probe in contact with a live
AC wire (without connecting the test lead probe). When contact is made
with a live wire, an audible tone will sound but no LED indicators will
light. This method is not recommended for determining that a wire is
safe to touch. If there is no reasonable option, be sure to verify the unit
is working as expected on a known voltage source.
Charging The Instrument
Allow your instrument’s internal power supply to charge by following
the procedures documented in “MEASURING VOLTAGE” steps 1 through
4, leaving the unit exposed to a voltage source (100 to 700 volts) for at
least 5 seconds.
Typically the instrument will retain its charge for at least 30 minutes
without being used, and will sustain the continuity tone for more than
one minute if recently charged.
Charging is required for all audio tone dependent functions.
Testing For Continuity
C o n t i n u i tyi ndicates that current can flow from one point to another. Yo ur
ECT600A will sound a tone when it senses less than approximately 900 K
Ohms between the two test probes. Although the volume and frequency of
this tone changes slightly with resistance, the instrument cannot “measure”
resistance. UEi makes numerous Digital Multimeters for this purpose.
1. Charge your instrument by placing the test probes in a wall outlet
for approximately 5 seconds.
2. Place the test probes at opposite ends of the circuit to be tested.
Ensure the probes are making good contact.
3. An audio tone sounds if a signal (voltage and current) can pass
between the two probed units.
CAUTION!
Approximately 1.5 Volts DC is present at the probe tips when the
instrument is fully charged. Some very sensitive electronic components,
( typically marked in a conspicuous manner), can be damaged by
low voltage s .
1. Positive Probe
2. Instrument Body
3. Voltage Indicator Panel
4. Negative Probe
5. Probe Guards
6. Test Leads
I n s t r u c t i o n s
Measuring Voltage
1. Remove the test lead from the storage clip on the back of
the instrument.
2. Place the test lead probe on one side of the circuit (i.e. ground
or neutral circuit).
3. Place the probe attached to the body on the other side of the
circuit (i.e. the hot circuit).
4. Observe indicated voltage and polarity (if applicable) on the
LED display.
NOTE: The current surge produced when initially charging or
testing with this instrument may cause low amperage beakers and
ground-fault-isolation beakers to trip.
5
1
2
3
ECT600A-MAN P. 2
4
6

M a i n t e n a n c e
Service
WARNING!
Repair and service of this instrument is to be performed by qualified
personnel only. Improper repair or service could result in physical
degradation of the meter. This could alter the protection from electrical
shock and personal injury this meter provides to the operator. Perform
only those maintenance tasks that you are qualified to do.
These guidelines will help you attain long and reliable service from
your instrument:
1. Keep your meter dry. If it gets wet, wipe it dry immediately.
2. Whenever pra c t i cal, keep the instrument away from dust and
dirt, which can cause premature wear and collect on
internal components.
3. Although your instrument is built to withstand the rigors of daily use,
it can be damaged by severe impacts. Use reasonable caution when
using and storing the instrument.
Cleaning and Decontamination
Periodically clean your meter’s case using a damp cloth. DO NOT use
abrasives, cleaning solvents or strong detergents, as they may damage
the finish or affect the reliability of the structural components.
Probe tips can be cleaned with an abrasive, adequate to remove
build-up, to ensure good electrical contact.
DANGER!
DO NOT submerge this instrument in liquid! Liquids may enter this
instrument during cleaning and leak out in subsequent use, exposing
the user to dangerous voltage during measurement.
Repair
This unit contains no user serviceable parts. In the event your
instrument is physically damaged or does not function properly,
please return the instrument to UEi following the warranty and
service instructions.
S p e c i f i c a t i o n s
Operating range
ECT600A-MAN P. 3
Vo l tage 12 to 600 Volts DC or AC (at 50 - 60 Hz)
M aximum voltage input 700 V DC or AC (ground to phase)
Single probe sensitivity = 100 - 700 V AC (audio only)
Co n ti nui ty Audio tone from 0 to 900 KΩ
(Requires changed instrument)
Output to unit under test: Approximately 2 µA at 1.5 V DC
Charging time: =/>5 sec @ =/> 100 and =/< 700 V AC
Recommended time between charges: 30 min @ no-load
Continuos operation time between charges: 60 + sec*
* O p e rating time is dependent upon time since last charge
Op erating temperatur e 14 - 131˚F (-10 - 55˚C) @ =/<85% RH
and humidity
Power consumption <250 mA (Continuos)
Di splay Vert ical panel of light emmiting diode LED s
Size (excluding 2- 1/6” (W) x 9-1/8” (H) x 1-3/4” (D)
detachable test lead) ( 53mm x 230 mm x 45 mm)
Weigh t .46 lbs. (210 Grams )
Power supply Rechargeable capacitor - draws power from source tested
Ac cura cy This instrument is not intended for precise measurement
LE D indicators will light when voltage approaches an
in dicated value, and remain lit when higher voltage is
ap plied
* 2 40 / 2 08volt cross sensitivity: The 240 volt LED begins to
illuminate at about 210 volts - Although some 208 volt
so urces may illuminate the 240 volt LED, it typically does
not fully illuminate until it reaches approximately 215 volts.
Re spons e 1 sec. max im um
Protection class IP 5 0
Over-voltage ca t e g o ry CAT III, 700 volts to ground
Pollution degree 2
Ca libration cy c l e Annual certification is recommended

Limited Warranty
The ECT600A is warranted to be free from defects in materials and workmanship for a period
of one year from the date of purchase. If within the warra n ty period your instrument should
become inoperative from such defects, the unit will be repaired or replaced at UEi’s option.
This warra n ty covers normal use and does not cover damage which occurs in shipment or
failure which results from alteration, tampering, accident, misuse, abuse, neglect or improper
maintenance. Batteries and consequential damage resulting from failed batteries are not
covered by warra n ty.
Any implied warranties, including but not limited to implied warranties of merchantability
and fitness for a particular purpose, are limited to the express warranty. UEi shall not be
liable for loss of use of the instrument or other incidental or consequential damages,
expenses, or economic loss, or for any claim or claims for such damage, expenses or
economic loss. A purchase receipt or other proof of original purchase date will be required
before warra n ty repairs will be rendered. Instruments out of warra n ty will be repaired (when
re p airable) for a service charge. Return the unit postage paid and insured to:
1-800-547-5740 • FAX: [phone]
www.ueitest.com • Email: [email protected]om
This warranty gives you specific legal rights. You may also have other rights which vary from
state to state.
ECT600A
Electrical Current Tester
Copyright © 2007 UEi ECT600A-MAN 1/07
PLEASE
RECYCLE