uhlmann & zacher CX8936 User manual

All contents current at time of publication. 10AF –V1.0 –03/15/2021
User Manual –CX6936/CX8936 FSMBLE
1. Lid including srews x4
2. Base plate with electronics
3. Cable inlet
4. Removable connector for pin 1-8
5. Removable connector for pins 9-16
6. Rotary switch
7. Button
8. LEDs
9. Mounting hole x2
screws are not included
Radio frequency: 2402 to 2480 MHz
Transmission power: 4mW
Power supply: 5-24V DC
Temperature range: 50°–131°F operating temperature
Relay connections: DC: max. 48V/0.7A - AC: max. 32V/0.5A
Overview / Included in delivery
Technical Data
The radio switching module is designed for installation on indoor walls. It is an extension of the locking system with a radio switching unit
and establishes a connection to the locking units via radio.
•Modifications of any kind whatsoever, with the exception of those described in the corresponding manual, are not permitted on the
products of Uhlmann & Zacher GmbH.
•Use only original parts and accessories of Uhlmann & Zacher GmbH to prevent malfunctions and damages.
•The products of Uhlmann & Zacher GmbH should not be used for locking emergency life-saving aids (e.g. defibrillator, emergency
medication, fire extinguishers etc).
•The products should not come into contact with paint or acids.
•Do not use the products in potentially explosive areas. The products should only be used within the defined temperature range.
•Electrical equipment should only be installed and assembled by qualified electricians.
•High risk of injury (electrical shock!) if the connecting cables are touched with the power supply switched on.
•Carry out installation and maintenance work only with the power supply switched off . Comply all applicable national safety codes
and standards.
•The manual should be handed over to the user by the person doing the installation.
•Uhlmann & Zacher shall not be liable for any damage to the door or the components in case of improper installation.
•Liability cannot be accepted for units that are wrongly programmed. If there are disruptions, such as access not possible to injured
persons, property damage or other damages, then Uhlmann & Zacher shall not be responsible.
Intended Use
Safety Instructions
2
3
54
6
7
9
19
8

All contents current at time of publication. 10AF –V1.0 –03/15/2021
User Manual –CX6936/CX8936 FSMBLE
C
Find a suitable position in range of locking
unit. Make sure that the surface is smooth,
dry and robust. Do not position several units
very closely to make sure their radio does
not interfere.
Mark drilling positions through mounting
holes and drill holes if necessary.
Use suitable flat headed screws and screw
ancors if necessary (both not included).
If you want to attach the cable from a side,
use large enough rubber or plactic spacers
to make sure the cable is not squeezed.
1
2
Installation
A
B
3Attach device to surface.
Attach cable to pins as required in your specific project. The two connectors and
for pin 1-8 and 9-16 are both removable. See table below for the correct pin assignment.
Power supply: 5-24 V DC | Relay connections: DC: max. 48V/0.7A - AC: max. 32V/0.5A
To pair the device with a locking unit, the assigned locking unit needs to be
in service mode. Usually the locking unit enters service mode if an
authorized service key is presented to the unit.
Use a screwdriver or a similar tool to set the rotary switch
to the position 8 then shortly press the button
to change to pairing mode.
Press button again to pair the device with a locking unit.
Close the device with the lid by attaching the 4 included screws.
7
6
Position: Function:
0
Default position. Press button
short to couple in paired
locking unit.
4Press button short to enter
service-mode
8
Press button short pairing for
pairing mode. Press augain
for pairing unpairing with a
locking unit.
1
4 5
9

All contents current at time of publication. 10AF –V1.0 –03/15/2021
User Manual –CX6936/CX8936 FSMBLE
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
Changes or modifications not expressly approved by Uhlmann & Zacher GmbH could void the user‘s
authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Canadian Compliance Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two
conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of
the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.