ULTRA-LINK UL-TMWT1230 User manual

1. Product Features:
Important: The Supplier and /or Manufacturer will not be held liable for any
personal injury or product damage due to mishandling, incorrect mounting, incorrect
assembly or incorrect use of this product.
Note: The supplied wall mounting hardware is not for use on steel stud walls or cold
cinder block walls. If you are uncertain what material your wall is constructed of or
have any questions regarding the proper installation of this wall mount, contact a
qualified contractor. If the hardware required is not included, please contact your
local hardware store.
Caution: This LCD/Plasma wall mount is intended for use on a LCD/LED/Plasma
television that does not exceed the maximum designated weight capacity. Using this
mount with products heavier than the maximum weight indicated may result in
instability causing possible injury.
Disclaimer
Without Prejudice of Rights
In order to indemnify the Supplier and/ or Manufacturer please note that once this product is
purchased the Client/ Purchaser agrees to the following:
Should the product .in an unlikely event, fail to operate according to its purpose,Interfoto CC
hereby declare to repair or replace any part of the mechanism which is found to be defective after
a full investigation as to the cause. In the case of defects occurring due to an external third party
and / or the Client / Purchaser installing it incorrectly, misuse or overloading and/ or using it for
any other purpose other than that for which it was intended, neglect or damage, external parties
repairing or modifying the mechanism in any way and or its spare parts, if the enclosed operating
instructions were not followed, the Supplier and /or Manufacturer shall not be held liable for any
damage caused to the product placed on the mechanism or wall which the mechanism is attached
to or any other property and personal injury.
Note: Proof of purchase to be produced for any claim. This product carries a ten year warranty for
manufacture faults/failures.
UL-TMWT1230 Product weight: 0.3 kg; TV size support : 12”-30” ; Distance to
the wall : 80mm ; Maximum load 20 kg ; For VESA standard : 100 x 100 mm
(The below hardware is not included with the purchase of this product.)
I. 6mm spanner II. 10mm spanner III. 8mm star screw driver IV. 8mm star screw driver
V. 8mm spanner VI. 8mm star screw driver VII. 6mm star screw driver
2. Hardware List:
IMPORTANT SAFETY INSTRUCTIONS
Check your TV user manual instructions to see if there are any special requirements for mounting your TV. If you do not understand
these instructions or have doubts about the safety of the installation, assembly or use of this product, contact:
INTERFOTO CC
Website: www.ultralink.co.za
Email: [email protected]
Address: 20 Roan Crescent,
Corporate Park North, Midrand
Tel: [phone]
UL-TMWT1230
Fixed Wall Installation

Use the spirit level to ensure the wall
plate is level, then Pre-drill 4 holes with a
8mm bit (50mm deep.) Insert wall
anchors (B) into the holes, then use long
bolts (A) to mount the wall plate to wall.
Use wallboard screw (A), Plastic screw
(B) to mount the TV set to the wall plate.
Then cover with plastic cover (H).
Instructions for installation
Use Long bolt (I or J), to mount
the TV set to the panel.
Fix the Panel to the Plastic Connector using
Carriage screw (D) , Iron washer (F) and
Screw nut (E).
Fix the Plastic Connector to the wall plate
with Carriage screw (C) , screw nut (E) and
plastic washer (K)
Then cover with plastic cover (G)
Use the spirit level to ensure the wall
plate is level, then Pre-drill 4 holes with a
8mm bit (50mm deep.) Insert wall
anchors (B) into the holes, then use long
bolts (A) to mount the wall plate to wall.
Use wallboard screw (A), Plastic screw
(B) to mount the TV set to the wall plate.
Then cover with plastic cover (H).
Instructions for installation
Use Long bolt (I or J), to mount
the TV set to the panel.
Fix the Panel to the Plastic Connector using
Carriage screw (D) , Iron washer (F) and
Screw nut (E).
Fix the Plastic Connector to the wall plate
with Carriage screw (C) , screw nut (E) and
plastic washer (K)
Then cover with plastic cover (G)