Ultra Secure Protect 800 User manual

Wireless
Vehicle Probe
** Vehicle Detection Probe with 800m Transmission
** Adjustable Sensitivity
** N/Open Output Relay
** Compatible with other Protect 800 Equipment
** IP 56 weatherproof control Box
User Manual
Environmental Informaon for Customers in the European
Union European Direcve 2002/96/EC requires that the
equipment bearing this symbol on the product and/or its
packaging must not be disposed of with unsorted municipal waste.
The symbol indicates that this product should be disposed of
separately from regular household waste streams. It is your
responsibility to dispose of this and other electric and electronic
equipment via designated collecon facilies appointed by the government or
local authories. Correct disposal and recycling will help prevent potenal
negave consequences to the environment and human health.
For more detailed informaon about the disposal of your old equipment,
please contact your local authories, waste disposal service, or the shop where
you purchased the product.
ULTRA SECURE LTD,
9-10 RYEHILL COURT,
LODGE FARM I/E, NORTHAMPTON, NN5 7EU
UNITED KINGDOM
www.ultrasecuredirect.com
Sales & Technical Helplines
Our Sales & Technical helplines are open
Monday to Friday from 8.00am to 5.00pm
SALES
++44 (0)1604 589414 (and press opon 1)
[e-mail]
TECHNICAL
++44 (0)1604 589414 (and press opon 2)
[e-mail]

Parts & Function
Power
Wires Outlets
Mounting Holes
Alternate Wires outlet
Padlock
Hole
Insert 3 CR123A batteries
into the battery compartment
Slide the power switch to “ON” position,
press the test button, the LED will light up
Installation
o
/ 7mm
25mm
84mm 144mm
Mounting the control box at a height above any possible Flood Level.
Pairing
Interval setting
Sensitivity
Relay output(N/O)
Sensitivity
Test Button
Battery Power
Sensor Probe input
Power Switch
Interval timer
GSM Dialer
Connect the sensing probe cable to the box. The Normal Open output relay can be connect
to a third party device ,such as a GS M dialer..
Set the receiver to pairing mode follow the instruction sheet of
the receiver. Press the test button inside the box to pair. Then
follow the instruction of the receiver to complete the operation.
You can set the trigger interval according to your
needs, this is the time the system take to re-set before
it can be triggered by the probe again.
Yo u ca n adjust the sensitivity as n e e d e d . H i g h
sensitivity can detect longer distances, but it is more
susceptible to interference and generate false triggers.
9s
5s
3s
You can using the alternate lower or side wire outlet to suit your
installation, removing and replacing blanking plugs where not used.
Using The Alternate Outlet
Operation
Install the sensor probe 1 - 2 inches (25 - 50 mm) under the roadside verge, with
the cable inside protective tubing to prevent damage general wear or wildlife.
place it in-line with thw driving direction. Adjust the sensitivity until when a car
passes it will trigger the control box and without causing false triggers.
Probe
The use of a silicone sealant around these outlets will increase
protection from water ingress
After the installation, it can be
locked with a padlock to prevent
outside interference.
After installation, press the test button to see if the receiver can receive the signal. If the
signal is not received, change the location, reinstall or change the receiver location.
Page 2 Page 3
Code Conflict
If the Sensor transmitter coding is the same as another transmitter you must change the code. When
you have changed the code must re-pair the bell press
* Slide the power switch to off position
* Press and hold the test button
* slide the power switch to on position
* the LED will blink slow for 5 time
then blink quick
* Code is changed
* Do not forget to pair the sensor
after code changed.