ultron GN-IT01 User manual

Focus on the technology of blending and juicingFocus on the technology of blending and juicing
GN-IT01

Using safetyWARNINGIt will be dangerous if this instruction manual isn't followed
Please read this manual carefully before using machine. Please keep the manual safe for future reference.
Please follow the important safety warnings below. Failure to follow the safety warnings may result in injury and/or harm to
Do not remove the jug cover when the machine is working. NEVER touch the rotating parts or blades at anytime.
If the machine is blocked by food when blending,turn off the machine immediately and check to see if anything hard like seeds
The volume of food can't be over 2/3 of the jug.Make sure the lid cover is fully closed before operating the machine.
Do not use this machine for grinding hard dry ingredients like nuts,coffee,bean etc.This will damage the machine and reduce
its operational life.
Consume the food/drink immediately after blending.Do not store for more than 6 hours after blending to prevent rotting food
Do not allow children to operate this machine.Store the machine out of the reach of children.
*Please be careful when cleaning.The blades are very sharp.QUESTION
4.FAULT
Product name: Portable recharging blenderBattery specification: 1200mAh X 2 7.4VModel: GN-IT01 Volume:350mlRated current: 17A Rated voltage: 7.4VMotor specification: 7.4V Rated power: 126WMotor rotating speed:16500rmp/min 15%
you and other people.Always follow the information in this instruction manual.
or stones are causing the blockage.Remove and then restart the machine.Always turn off the machine before checking.
and drink.
GN-IT01
1. PARTS NAME-01--02--03--04-!2.OPERATION3.CHARGING4.FAULT

1.PARTS NAME
1. When the jug is separated from the base or not installed correctly, the blender
will not work and the red light will flash 5 times.
2. When it is charging ,the machine will not work no matter how many you press
the switch button.
3. If any food overloads or blocks the blender from working during operation.It
will stop automatically and the red and white lights will flash alternately.
4.The red light will flash 10 times when the battery has no power.
IMPORTANT!
2.It is best to charge the machine for between 3-5 hours.
3.The best blending performance is 100g food+200g liquid ( 10%).(indicating that it will not work.)Indicating light explanation
1.Blending function:Press the switch and hold for 2 seconds. The blender will start automatically and the white light will be on. After 45 seconds the machine will stop automatically.
2.Crush ice function: Press the switch twice continuously. The blender will start automatically and the white light will be on. After 45 seconds the machine will stop automatically.3.When the whole machine or just the battery connected to a USB charging lead, the red light on the battery will be on. When the machine is fully charged and ready, the white light on the battery will be on.
1.There will be a tolerance for the glass bottle due to special process, if your glass bottle leak or screw loose, please unscrew the bottle and reverse installation.
COVERHIGH BOROCILICATE GLASS JUGBLADEMAIN BASEBATTERY SETBASE2.OPERATION
1.Cut food to several pieces, remove the skin and nut ( around 1.5-2.0cm). Pour water and milk into the container.
2.Incline the machine to the angle of 45°,and then start the machine by pressing the switch for 2 seconds. 3.Upside down the blender and shake the bottle gently to make it more delicious. The blender will stop after 45s.

3.CHARGING03Battery capacity is 1200mAh x2,please use USB wire for charging connected to an adapter(2A or below 2A),power bank, USB port of computer or car charging port.
CHARGING PHOTO:(Magnetic Charging)
1.Please connect the magnetic suction port of the USB wire to the magnetic suction port on the base.
2.Please insert “USB side”(bigger side of USB wire) into adapter,power bank,USB port of computer and etc.
NOTICE:
The red light indicates the machine is charging.When charging is completed,the light will turn white
The machine will not work during charging.
Battery set charging Whole machine charging
0404
1.Ready 40-45g ice cube (around 1.5-2.5cm length/width/ height). Put the ice cube into the container.
2.Incline the machine to the angle of 45°,and then start the machine by pressing the switch twice continuously. 3.Upside down the blender and shake the bottle gently to make it more delicious. The blender will stop after 45s.
1. Put the jug on the main base, and then turn clockwise fully to lock.2. Connect the main base to the battery set. (Press the switch button to operate with white light).3. Put the whole machine on the base.
*EASY INSTALLATION2.OPERATIONNEW function: Crush ice

104054.FAULTWARM REMIND:1.The machine should only be used when water,milk or other liquids are inside the container at a height above and covering2.Do not wash the base of the machine with water.Do not submerge the base in water.If water is allowed into the switch or the blades.If food does not blend,add more liquid.charging port,the machine will be damaged.Fault phenomenonFault analysisSolutionNoThe red light flashes 5 timesbut the machine doesn't work. The container is not correctly installed on the base.Please re-install again.2The machine doesn't work and the red light is flashes 10 times.Battery quantity is not enoughor no power.Please charge the machine for 3-5 hours.3The machine stops duringoperation.Too little food or too much.Either will cause the machine to stop for pro-tection.Please add or reduce some food andre-start the machine.4The red and white light will flash 10 times during operation.The motor has locked.If there isn't any food blockage, please re-start again.5Leaking water.The silicone part is not installed correctly.Please re-install silicone part.6There is some smoke when using.Long time using, the machine is over heated and protected automatically.Please cool down the machine for 30-60 mins and then start again.