Uncle Bills Asia Pacific S002379 User manual

4 Unit Swing Set with Slide
S002379
Instruction Manual
WARNING: To ensure your safety, please do not attempt to assemble this swing set
without reading this instruction manual carefully. Failure to comply with this warning
may result in injury and/or property damage.
• This product includes small parts/accessories that are not suitable for children under 3
years of age as they may cause a choking hazard.
• This product should be assembled by 2 adults.
• Only use this product on a so, flat level surface.
•DO NOT ALLOW CHILDREN TO PLAY ON THIS SWING SET UNSUPERVISED!
CONSTANT ADULT SUPERVISION IS REQUIRED.
• This product is designed for domestic use only.
ATTENTION!
ASSEMBLY, INSTALLATION, CARE, MAINTENANCE AND USE INSTRUCTIONS.
PLEASE READ ALL SAFETY INFORMATION PRIOR TO USE.
WARNING: READ THESE MATERIALS PRIOR TO ASSEMBLING
AND USING THIS SWING SET
POUR LE MANUEL D’INSTRUCTIONS EN FRANÇAIS, VOIR LA PAGE 37.

2S002379 4 unit swing set
EN
Contents
3 Warnings
12 Tools Required
13 Parts List
18 Assembly Instruction Warning
19 Assembly Instructions
35 Warranty information
Languages
3 English
37 Français
EN
FR

3S002379 4 unit swing set
EN
Warnings
To reduce the risk of serious injury, read the entire manual before you assemble or use
this swing set. In particular, please note the following safety precautions. Please keep this
manual in a safe place for future reference.
1. This swing set includes small parts/accessories that are not suitable for children
under 3 years of age as they may cause a choking hazard.
2. It is the responsibility of the owner to ensure that all users of this swing set are
adequately informed of all warnings and precautions. This swing set is not intended
for use by persons (including children) with reduced physical, sensory or mental
capabilities; or lack of experience and knowledge unless they have been given
supervision or instruction concerning use of the swing set by a person responsible for
their safety.
3. This swing set should be assembled by 2 adults.
AGE LIMIT
1. This product is designed to be used by up to six (6) children between the ages of 3
to 8. Maximum user weight is 100 pounds (45 kg) each with a combined maximum
weight of 600 pounds (272kg).
2. The swing set is designed for children over three (3) years of age up to (8) years of
age. Use by smaller children can result in entrapment or serious injury.
3. On-site adult supervision is required at all times for children of all ages.
4. Do not allow use by children with any physical condition that may affect his/her ability
to use this equipment safely.
5. Do not allow children to use the equipment in a manner other than intended.
6. Children must not use the equipment until it is properly assembled and anchored.
7. Adult supervision is required during the use of this equipment at all times.
8. Unpack all parts. Take a complete inventory of all parts and hardware using the parts
and hardware lists in the following pages. If any parts are missing, do not return to
the store. Please call customer service toll-free number listed on the cover page for
assistance. Store the product back in the original box and do not begin to install until
all parts are obtained.

4S002379 4 unit swing set
EN
LOCATION OF PLAY SET
1. The equipment must be placed more than six (6) feet (1.8 meters) from any structures
or obstructions, including but not limited to buildings, fence, garage, trees, laundry
lines, electrical wires. Children can be seriously injured running or swinging into
obstacles.
2. The swing set must be installed on level ground. Uneven ground must be levelled prior
to installation. Installation on sloping or uneven ground will put stress on the joints,
causing the unit to become loose and unstable which may result in serious injuries.
3. Remove any tripping hazards from the safe play area, such as roots, tree stumps,
rocks, landscaping, sprinkler heads, railroad ties, plumbing and electrical connections.
4. It is highly recommended that you seek the opinion from a local licensed contractor on
the best way to secure the swing set in your location.
5. Windy conditions: it is possible for the product to be blown about by a high wind. If you
anticipate high winds, the frame should be secured to the ground with the use of an
Anchor kit. If you anticipate severe winds, the product should be moved to a sheltered
location or completely disassembled.
6. Do not install your play set over hard surface, e.g. asphalt, concrete, packed earth,
tile or brick floor. A fall onto a hard surface can result in serious injury or death to
the user. The following is a list of recommended ground covers from the Consumer
Product Safety Commission:
SUGGESTED MATERIAL UNCOMPRESSED DEPTH
Double Shredded Bark Mulch 9” (23cm)
Uniform Wood Chips 12” (31cm)
Fine Gravel 12” (31cm)
Fine Sand 12” (31cm)
The Consumer Product Safety Commission’s Outdoor Home Playground Safety Handbook
recommends to install and maintain the playground equipment over at least 9 inches
(23cm) of wood chips, mulch or shredded rubber (for equipment up to 8 feet high (244cm))
or sand or pea gravel (for equipment no more than 5 feet high(152cm)) as shock absorbing
material. Dirt and grass, which are the most prevalent surfaces under home playground
equipment, do not adequately protect children from serious head injuries. Install
protective surfacing at least six feet in all directions from play equipment. For swings,
the surface should extend, in back and front, twice the height of the suspending bar. You
should consult a local contractor about ways to secure the product in your location. Do not
Warnings (cont)

5S002379 4 unit swing set
EN
Warnings (cont)
install your play set over hard surface, e.g. asphalt, concrete, packed earth, tile or brick
floor. Please refer to the CONSUMER PRODUCT SAFETY COMMISSION’S OUTDOOR HOME
PLAYGROUND SAFETY HANDBOOK for detailed guidelines to prevent injuries from falls
and other hazards on public and home playgrounds.
SELECT PROTECTIVE SURFACING
One of the most important things you can do to reduce the likelihood of serious head
injury’s is to install shock-absorbing protective surfacing under and around your play
equipment. The Protective surfacing should be applied to a depth that is suitable for the
equipment height in accordance with ASTM F1292.
NOTE: DO NOT install home playground equipment over concrete, asphalt, or any other
hard surface. A Fall onto a hard surface can result in serious injury to the equipment user.
Grass and dirt are not considered protective surfacing because wear and environmental
factors can reduce their shock absorbing effectiveness.
Carpeting and thin mats are generally not adequate protective surfacing. Ground Level
equipment - such as Sand-Box, activity wall, playhouse or other equipment that has no
elevated play surface - does not need any protective surfacing.
WARNINGS ON ANCHORING
It is highly recommended the product be anchored into the ground to prevent movement
and to make the swing set more stable during use.
Some consumers want an anchoring system that allows the product to be moved to
different locations. Other consumers want to keep their swing set in a permanent location.
It is highly recommended that you seek the opinion from a local licensed contractor on
the best way to secure the swing set in your location. The best way to anchor a product is
to create a concrete footing and use that as a base for an anchor. Whatever method you
prefer for your location, an anchoring system for this product should be used at all times.
WEATHER CONDITIONS
1. DO NOT use this equipment if the swing seat, slide or any parts are wet. Use the play
set only when the parts are clean and dry. If the equipment is wet, the user could slip
and suffer injuries.
2. Please be aware of weather conditions when using the equipment. If it is too windy,
users could lose control and suffer injuries. The playground equipment must be
properly anchored, stored away or restricted from use during inclement weather such
as heavy winds or severe weather storms. You should consult a local contractor about
ways to anchor the product in your location.

6S002379 4 unit swing set
EN
Warnings (cont)
WARNING STATEMENTS
Observing the following statements and warnings reduces the likelihood of
serious or fatal injury.
1. DO NOT allow more than one child to play on the individual swing or slide component
at any one time.
2. DO NOT allow children to stand on the slide, swing seats or glide ride. The glide ride is
made for only two users at a time.
3. DO NOT allow children to walk too close to moving parts. ALWAYS keep a safe
distance to avoid being struck by other children while playing on swings, slides,
trapeze, and glide ride etc.
4. DO NOT allow children to hang upside down on trapeze bar!
5. DO NOT allow children to twist the swing chains or loop them over the top support bar
as this may reduce the strength of the chain.
6. DO NOT swing empty seats as this may cause injuries.
7. Children should not walk close to, in front of, behind, or between moving items.
8. DO NOT CLIMB on the Equipment when the Equipment is wet.
9. DO NOT attached items to the equipment that are not specifically designed for use
with the equipment, such as, but not limited to, Jump Ropes, Clothesline, pet leashes,
cables, and chain as they may cause a strangulation hazard.
10. Dress Children with well-fitting and full foot enclosing footwear. Examples of in-
appropriate footwear are: CLOGS, flip flops, and sandals.
11. ALWAYS guide children to sit in the center of swinging parts, with their full weight
placed in the seat center and holding on to the swing chains.
12. DO NOT allow children to jump off the equipment while it is in motion. ALWAYS come
to a full stop before dismounting.
13. ALWAYS dress children appropriately for proper play, e.g. wear well-fitted rubber sole
shoes, and remove loose or sharp items such as jewellery, hair accessories, scarves
which may become entangled in the equipment or cause injuries.
14. ALWAYS make sure children remove their bike or other sports helmets before playing
on the swing set.
15. DO NOT allow children to slide down the slide head first.

7S002379 4 unit swing set
EN
Warnings (cont)
16. DO NOT allow children to climb onto swing or jump to/from different play areas of the
equipment.
17. ALWAYS return safely to the ground before approaching another play area.
18. DO NOT allow children to climb on structural parts (e.g. legs, top bar). These are
structural components and are not designed for play.
19. ALWAYS check the slide or other parts exposed to the body for extreme heat from the
sun before allowing children to use the equipment.
20. ALWAYS prevent access and secure from any unauthorized use when there is no adult
supervision.
21. DO NOT allow pets or other animals near the equipment to prevent damage or
injuries.
22. Adequate overhead clearance is essential. A minimum of 24  (7.3 meters) from
ground level is recommended. Provide clearance for wires, tree limbs, and other
possible hazards.
23. Use the swing set in a well-lit area. Artificial illumination may be required for shady
areas.
INSPECTION PRIOR TO EACH USE OR DAILY INSPECTION
1. DO NOT use the equipment if any bolts or nuts are missing or loose. ALWAYS check to
ensure the equipment and all parts are well secured and stable before each use.
2. ALWAYS clear the play area of any rocks, sharp objects, or any materials that could be
potentially hazardous to users.
3. DO NOT attach items to the equipment that are not specifically designed for use with
the equipment, including, but not limited to, jump ropes, clothesline, pet leashes,
cables and chains as they may cause choke hazards.
4. The steel and plastic parts used in your product are subject to normal wear. Gradual
deterioration of the material will occur, the speed of which will depend on the level
of exposure to UV rays, airborne pollution, outdoor weather conditions such as rain
and wind and the amount of use. You must inspect the equipment prior to every use.
This includes, but is not limited to inspecting the set for cracks, excess wear, missing
parts, loose connections, and for overall integrity. When the set shows any signs of
weakness, you must stop using the swing set immediately, properly store the set or
restrict access by users until the condition is resolved.
5. Verify that the chains are secured at both ends and tightened, so that there is no loose
chain hanging that can result in choking hazard.

8S002379 4 unit swing set
EN
NOTE: When conducting inspections, it is recommended that you use the Suggested
General Maintenance Checklist and Routine Inspection and Maintenance Issues checklists
provided by the US Consumer Product Safety Commission, a copy of which is contained in
this user manual.
CARE & MAINTENANCE INSTRUCTIONS
1. Inspect all nuts and bolts twice monthly during the usage season for tightness and
tighten as required. It is particularly important that this procedure is followed at the
beginning of each season.
2. Oil all metallic moving parts monthly during the usage period.
3. Sand rusted areas on metal tubing and repaint using a non-lead based paint meeting
the requirements of Title 16 CFR Part 1303.
4. Check swing seats and chains monthly during usage season for deterioration.
Replacements should be made in accordance with the manufacturer’s instructions.
5. Check all coverings for bolts and sharp edges twice monthly during usage season to
be certain that they are in place and replace when necessary. It is especially important
to do this at the beginning of each new season.
6. Do not use when the temperature drops below 32 degrees F (0 degrees C); remove
and store the plastic swing seats and slide indoors.
ANCHORING
There are different ways of anchoring the equipment, depending on the type of ground on
which the equipment is to be installed. Make sure that all anchors are below ground level
to prevent tripping.
You should consult your local contractor to decide the most appropriate way to anchor the
equipment in your location.
The following anchoring options may be considered:
Corkscrew Anchoring (Corkscrew Anchors not included)
1. If your soil is hard (clay, etc.), the corkscrew method may be suitable.
2. Be sure that the swing set is located on level ground.
3. Twist the corkscrew anchor into the ground until only the end with the hook is above
the ground and next to the leg. Insert the hook into the bottom opening of the leg.
4. Ensure that the hook is secured onto the leg opening.
Warnings (cont)

9S002379 4 unit swing set
EN
5. All rusted parts, bolts must be properly disposed of in trash bin. Do not reuse.
OWNERS shall be responsible for maintaining the legibility of the warning labels.
Concrete Anchoring (Materials not included)
1. If the swing set is set up on grounds with sandy soil (so) condition, it must be
anchored with concrete footing (concrete not included)
2. Be sure that the swing set is assembled and placed on level ground
3. Dig holes around swing leg tube, as shown in drawing in the next page. As you dig
deeper, enlarge the diameter of the hole to fix the cement
4. Place 2 inches of brick or gravel underneath the leg
5. Use about 45 lbs. of concrete per leg
6. Cover the concrete with dirt and protective surface material
7. Allow 6-7 days for the concrete to dry properly
Warnings (cont)

10 S002379 4 unit swing set
EN
NOTE: The maximum fall height for this product is 4 feet (122cm). The minimum ground
clearance between the bottom of the suspended plays and the playing or ground surface
must be 8 inches (21cm).
You must maintain a minimum of 8 inches (21cm) of ground clearance.
WARNING
Please properly anchor the swing set to minimize the risk of injury or death. If the swing
set is used without proper anchoring, it may be dangerous and may tilt over.
CARE AND MAINTENANCE CHECKLIST
At the beginning of each play season:
1. Tighten all hardware.
2. Lubricate all metallic moving parts per manufacturer’s instructions.
3. Check all protective coverings on bolts, pipes, edges, and comers. Replace if they are
loose, cracked, or missing.
4. Check all moving parts including swing seats and chains for wear, rust or other
deterioration. Replace as needed.
5. Check metal parts for rust. If found, sand and repaint using a non-lead paint meeting
the requirements of 16 CFR 1303.
6. Reinstall any plastic parts, such as swing seats or any other items that were removed
for the cold season.
7. Rake and check depth of loose fill protective surfacing materials to prevent
compaction and to maintain appropriate depth. Replace as needed.
Warnings (cont)

11 S002379 4 unit swing set
EN
Twice a month during play season:
1. Tighten all hardware.
2. Check all protective coverings on bolts, pipes, edges and comers. Replace if they are
loose, cracked or missing.
3. Rake and check depth of loose fill protective surfacing materials to prevent
compaction and to maintain appropriate depth. Replace as needed.
Once a month during play season:
1. Lubricate all metallic moving parts per manufacturer’s instructions.
2. Check all moving parts including swing seats and chains for wear, rust or other
deterioration. Replace as needed.
3. Rake and check depth of loose fill protective surfacing materials to prevent
compaction and to maintain appropriate depth. Replace as needed.
At the end of each play season:
1. At the end of each play season or when the temperature drops below 32 degrees F (0
degrees C).
2. Remove plastic swing seats and other items as specified by the manufacturer and take
indoors or do not use.
3. Rake and check depth of loose fill protective surfacing materials to prevent
compaction and to maintain appropriate depth. Replace as needed.
4. As a general rule, maintenance should be performed at any time it is deemed
necessary.
DISPOSAL INSTRUCTIONS
1. Please use care when disassembling the equipment, when it is no longer in
operational condition. Wear heavy duty working gloves to avoid injuries.
2. Fully disassemble the entire swing and slide sets before disposal. Do not leave
partially disassembled parts in areas accessible by children.
3. Should you wish to recycle the steel tubing, please take the frame to your local
recycling center.
4. All plastic parts can be recycled, take it to your local recycling center. Do not let
children play with any disassembled parts meant for disposal, such as chains, slide,
tubing, bolts, nuts, screws, etc.
Warnings (cont)

12 S002379 4 unit swing set
EN
Tools Required
Description Included
Special Socket Wrench Y
Tape Measure N
Hammer N
Wrench Y
Wrench N
Flat Head Screwdriver N
Philips Head Screwdriver N
Large Allen Key Y
Medium Allen Key Y
Small Allen Key N

13 S002379 4 unit swing set
EN
Parts List
Part list for main frame assembly
Part No. Description Qty
A1 Le top bar 1
A2 Middle top bar 1
A3 Right top bar 1
A4 Top section leg 4
A5 Bottom section leg with foam 4
A6 Cross bar (with two holes) 1
A7 Cross bar (with four holes) 1
Hardware for main frame assembly
Part No. Description Qty
B1 Bolt 5/16” x 2-1/2” (8 x 64mm) 16
B2 Bolt 5/16” x 2-3/4” (8 x 69mm) 4
B3 Nylon nut 5/16” (8mm) 20
B4 Plastic cap with Arc washer 20
B5 Arc washer 5/16” (8mm) 16
B6 Washer 5/16” (8mm) 4

14 S002379 4 unit swing set
EN
Parts List (cont)
Bracket for glide ride assembly
Part No. Description Qty
L3 Bracket 1
L4 Bracket clamp 1
L5 Reinforcing steel spacer 2
N3R Bolt 5/16”x1” (8 x 25.4mm) 2
N7 Nylon nut 5/16” (8mm) 2
Parts list for glide ride assembly
Part No. Description Qty
L1-N Top section 2
L3-N Glide seat support 2
M1 Tube Cap 2
M2 Small nylon bearing 2
M3 Large nylon bearing 4
M4 Glide seat 2
M5 Footrest 2

15 S002379 4 unit swing set
EN
Parts List (cont)
Hardware for glide ride assembly
Part No. Description Qty
N1 Bolt 1/4” x 1-1/2” (6.4 x 38mm) 4
N2R Bolt 1/4” x 1-3/4” (6.4 x 45mm) 2
N4 Screw 0.22”x3/4” (5.5 x 19mm) 4
N5 J-bolt 2
N6 Spring Washer (small) 4
N8 Cap bolt 1/4”x1/2” (6.4 x 13mm) 2
N9 Cap nut 1/4” (6.4mm) 4
N10 Nut 1/4” (6.4mm) 2
N11 Spring washer (large) 2
N12 Spring washer (medium) 4
Parts list for swing seat assembly
Part No. Description Qty
J1 PVC covered chain 4
J3 Eyebolt with attachment bolt 8
K1 Swing seat 2

16 S002379 4 unit swing set
EN
Parts List (cont)
Hardware for swing seat assembly
Part No. Description Qty
J6 Nylon nut 5/16” (8mm) 8
J7 Washers 5/16” (8mm) 4
J8 Plastic cap (with arc washer) 4
J9 Plastic cap (with flat washer) 4
Parts list for trapeze assembly
Part No. Description Qty
P1 Trapeze 1
T3 Rubber cap 2
S1 Eyebolt with chain 2
Hardware for trapeze assembly
Part No. Description Qty
S3 Plastic cap (with arc washer) 2
P4 Nylon nut 5/16” (8mm) 2

17 S002379 4 unit swing set
EN
Parts List (cont)
Parts list for slide assembly
Part No. Description Qty
X1-N Slide support (with opening) 1
X2-N Slide support 1
X3-N Slide leg tube 2
X4-N Slide top support bar 1
X5-N Slide front support 1
X6 Slide ladder steps 2
Y2 Slide 1
Parts list for trapeze assembly
Part No. Description Qty
Y1 Plastic connector 2
Z1 Bolt 1/4”x1-1/3” (6.4 x 34mm) 4
Z1-1 Bolt 1/4”x1-1/2” (6.4 x 38mm) 2
Z2 Bolt 1/4”x4-1/2” (6.4 x 114mm) 2
Z3 Spring washer 4
Z4 Cap nut 1/4” (6.4mm) 10
Z5 Cap bolt 1/4”x1/2” (6.4 x 13mm) 4
Z6 Spring washer (small) 20
Z7 Bolt 1/4”x3” (6.4 x 76mm) 2
Z8 Bolt 1/4” x2-1/4” (6.4 x 57mm) 4

18 S002379 4 unit swing set
EN
Assembly Instructions Warnings
1. Place the swing set equipment on level ground and not less than 6 (1.8m) from
any structure or obstruction such as a fence, garage, house, overhanging branches,
laundry line, or electrical wires.
2. Do not install the swing set equipment over concrete, asphalt, packed earth, or any
other hard surface; a fall onto a hard surface can result in serious injury or death to
the equipment user.
3. Adequate overhead clearance is essential. A minimum clearance from ground level
shall be recommended. Provide clearance for wires, tree limbs, and other possible
hazards.
4. Use the swing set in a well-lighted area. Artificial illumination may be required for
shady areas.
5. Secure the swing set against unauthorized and unsupervised use.
6. The owner and supervisors of the swing set are responsible to make all users aware
of practices specified in the use instructions.
TIGHTENING NUTS & BOLTS
1. For ease of installation, do not over-tighten the nuts and bolts when you are first
putting the equipment together. This will allow for some possible adjustments during
installation.
2. Once you have finished assembling each component of the play set, make sure to go
back over each step and properly tighten all nuts, bolts and plastic caps. Check the
entire unit to ensure all parts are properly assembled before allowing children to use
the swing set equipment.

19 S002379 4 unit swing set
EN
Assembly Instructions
STEP 1 -Assemble the top bar frame of the swing set
Connect A1, A2 and A3 secure with B1, B3, B4 and B5 as shown below.
NOTE: All round holes should be facing up and concave holes facing down.
During periods of non-use, the swing set can be disassembled and stored.
Prior to assembling this swing set, remove all parts from the carton and check to ensure
that all parts listed in the Parts List on page 12 are present. If you’re missing any of the
parts, please call our National Service Centre to have replacement parts sent out prior to
beginning assembly (details can be found in the warranty pages at the end of this manual).
NOTE: It is recommended that two adults assemble this swing set.

20 S002379 4 unit swing set
EN
Assembly Instructions (cont)
STEP 2 -Assemble the support legs of swing set
1. Connect A1 to A4 and secure using 81, 85, 84 and 83 as shown below.
2. Repeat the above step for the right side of the swing set (A3 and A4, A5).