Uniden EXA 7250 Series User manual

EXA 7250
SERIES
OWNER'S
MANUAL

[1]
www.uniden.com
Contents
Welcome/Features 2
Controls & Functions 3
Terms Used in this Manual 4
Getting Started 5
Installing the Phone 5
A. Choose the Best Location 5
B. Install the Rechargeable Battery Pack into the Handset 6
C. Connect the Base Unit and Charge the Handset 7
D. Mount the Base Unit on a Wall 8
E. Choose the Dialing Mode 9
Basics 10
Using Your Phone 10
Making and Receiving Calls 10
Adjusting the Ringer and Earpiece Volume 11
Tone Dialing Switch-over 12
Traveling Out-of-Range 12
Selecting a Different Channel 13
Find Handset 13
Using Call Waiting 13
RocketDial 14
RocketDial 14
Storing the RocketDial 14
Using the Speed Dial Memory 15
Using the Speed Dial Memory 15
Storing Numbers in Speed Dial Memory 15
Making Calls from Speed Dial Memory 15
The Integrated Answering Device 16
The Integrated Answering Device 16
Turning the Answering System On/Off 17
Setting Up Your Answering System 18
Using Your Answering System 27
Remote Operation 32
Additional Information 37
Changing the Digital Security Code 37
Note on Power Sources 38
General Information 40
Troubleshooting 41
Liquid Damage 44
Precautions & Warranty 45
I.C. Notice 47
Index 48
Remote Operation Card
Uniden EXA3245.book 1 ページ ２００４年２月４日 水曜日 午後６時１８分

[2]
www.uniden.com
Congratulations on your purchase of the Uniden cordless telephone and answering system.
This phone is designed and engineered to exacting standards for reliability, long life, and
outstanding performance.
Note: Illustrations in this manual are used for explanation purposes. Some illustrations in
this manual may differ from the actual unit. The color of your cordless phone may vary.
As an Energy StarPartner, Uniden has determined that this product or product models meets the
Energy Starguidelines for energy efficiency.
Energy Staris a U.S. registered mark.
WELCOME/FEATURES/
TERMINOLOGY
Welcome
Features • 2.4GHz Extended Range Technology
• Integrated Telephone Answering Device
(ITAD)
• Trilingual Voice Prompts (English, French
or Spanish Support)
• 10 Number Memory Dialing
• One touch RocketDial®
• Last Number Redial
• Flash and Pause
• Tone/Pulse Dialing
• Find Handset Locator
• Earpiece Volume Control
•RingerVolumeControl
• Hearing Aid Compatible
• 20 Channel Autoscan
Be sure to visit our web site: www.uniden.com
Uniden® and RocketDial® are registered trademarks of Uniden America Corporation.
AutoTalk, AutoStandby, UltraClear Plus, Random Code, and AutoSecure are trademarks of
Uniden America Corporation.
Uniden EXA3245.book 2 ページ ２００４年２月４日 水曜日 午後６時１８分

[3] CONTROLS & FUNCTIONS www.uniden.com
Controls & Functions
4
3
5
6
7
8
1
4
9
1
3
1
5
1
0
11
1
2
2
1
Play
Skip
Stop
Delete
Repeat
CONTROLS &
FUNCTIONS
1. Handset antenna
2. Handset battery compartment
3. Handset earpiece
4. talk/batt low LED
5. remote key (pages 9 and 35)
6. vol (volume)/ key (page 11)
7. */tone key (page 12)
8. redial/pause key (pages 10 and 15)
9. memory key (page 14)
10. Rocketdial key (page 14)
11. talk/flash key (pages 10 and 13)
12. end key (pages 10 and 11)
13. channel key (page 13)
14. Handset microphone
15. Handset charging contacts
Retrieve TAD message
with Handset Remote keys
Uniden EXA3245.book 3 ページ ２００４年２月４日 水曜日 午後６時１８分

CONTROLS & FUNCTIONS [4] www.uniden.com
CONTROLS &
FUNCTIONS
16. Telephone line jack
17. DC IN 9V jack
18. Base antenna
19. Base speaker
20. (repeat/rewind) key (page 28)
21. memo rec (record) key (page 31)
22. menu/clock key (page 18 and 19)
23. ringer key (page 26)
24. Base charging contacts
25. charge in use LED
26. (play/stop) key (pages 26 and 27)
27. (skip/fast forward) key (page 29)
28. (delete) key (page 30)
29. greeting key (page 25)
30. answer on/off key (page 17)
31. set key (page 18)
32. find hs (handset) key (pages 13 and 37)
33. / /volume/select keys (page 18 and 26)
34. mic (microphone)
Terms Used in this Manual
• Standby Mode -The handset may be sitting in or off the base, but is NOT in use. The talk/flash key has
not been pressed and there is no dial tone.
• Talk Mode - The handset is off the base and the talk/flash key has been pressed, enabling a dial tone.
• RocketDial - One touch speed dial
17
18
25
26
27
28
29
30
32
34
33
31
16
20
19
21
22
23
24
Uniden EXA3245.book 4 ページ ２００４年２月４日 水曜日 午後６時１８分

[5] GETTING STARTED www.uniden.com
Installing the Phone
Do the following steps:
A. Choose the Best Location
B. Install the Rechargeable Battery Pack into the Handset
C. Connect the Base Unit and Charge the Handset
D. Mount the Base Unit on a Wall
E. Choose the Dialing Mode
A. Choose the Best Location
When choosing a location for your new phone, here are some important guidelines you should
consider:
• The location should be close to both a phone jack and a continuous power outlet (one
which is not connected to a switch).
• The base and handset should be kept away from sources of electrical noise such as motors,
microwave ovens, and fluorescent lighting.
• The base can be placed on a desk, tabletop, or mounted on a standard wall plate.
• There should be enough space to fully extend the antenna.
Avoid heat sources, such as radiators,
air ducts, and sunlight
Avoid television sets and other
electronic equipment
Choose a central location
Avoid noise sources such as a window by
a street with heavy traffic
Avoid microwave ovens
Avoid excessive moisture,
extremely low temperatures, dust,
mechanical vibration, or shock
Avoid personal computers
Avoid other cordless telephones
If your home has
specially wired alarm
equipment connected to
the telephone line, be
sure that installing the
system does not disable
your alarm equipment.
If you have questions
about what will disable
your alarm equipment,
contact your telephone
company or a qualified
installer.
note
GETTING STARTED
Uniden EXA3245.book 5 ページ ２００４年２月４日 水曜日 午後６時１８分

GETTING STARTED [6] www.uniden.com
B. Install the Rechargeable Battery Pack into the Handset
The handset is powered by a rechargeable battery pack. The
battery recharges automatically when the handset is placed in
the base unit.
1) Press down on the handset battery case cover (use the
finger indention for a better grip) and slide the cover
downward to remove.
2) Plug the battery pack connector (red & black wires) into the
jack inside the battery compartment.
(The connector notches fit into the grooves of the jack only
one way.) Match the wire colors to the polarity label in the
battery compartment, connect the battery and listen for a
click to insure connection.
3) Make sure you have a good connection by slightly pulling on
the battery wires. If the connection is secure, the battery
jack will remain in place.
4) Place the battery case cover back on the handset by sliding
it upwards until it clicks into place.
•Use only the Uniden
(BT-905)
rechargeable battery
pack supplied with
your cordless
telephone.
•Replacement batteries
are also available
through the Uniden
Parts Department at
[phone],
Monday through Friday
from 8:00 a.m. to 5:00
p.m. or online at
www.uniden.com
!
GETTING STARTED
Uniden EXA3245.book 6 ページ ２００４年２月４日 水曜日 午後６時１８分

[7] GETTING STARTED www.uniden.com
•Use only the supplied
AD-314 AC adapter.
Do not use any other
AC adapter.
•Do not place the power
cord where it creates a
trip hazard or where it
could become chafed
and create a fire or
electrical hazard.
!
GETTING STARTED
C. Connect the Base Unit and Charge the
Handset
1) Connect the AC adapter to the DC IN 9V jack and to
a standard 120V AC wall outlet.
2) Place the handset in the base unit with the keypad
facing forward.
3) Make sure the charge in use LED illuminates.
If the LED does not illuminate, check to see that the AC adapter
is plugged in and the handset makes good contact with the base
charging contacts.
•Connect the AC adapter to a continuous power supply.
•Place the base unit close to the AC outlet so that you can
unplug the AC adapter easily.
4) Charge your handset at least 15-20 hours before plugging into
the phone line.
5) Once the handset battery pack is fully charged,
connect the telephone line cord to the TEL LINE
jack and a telephone outlet.If your telephone
outlet isn't modular, contact your telephone
company for assistance.
Uniden EXA3245.book 7 ページ ２００４年２月４日 水曜日 午後６時１８分

GETTING STARTED [8] www.uniden.com
GETTING STARTED
D. Mount the Base Unit on a Wall
Standard wall plate mounting
This phone can be mounted on any standard wall plate.
1) Locate the base unit on the wall
mount adapter as shown and slide
the wall mount adapter into the
notches on the base bottom.
2) Plug the AC adapter to the DC IN 9V
jack.
3) Route the AC adapter cord through
the molded wiring channel as shown.
4) Plug the AC adapter into a standard
120V AC wall outlet.
5) Plug the telephone line cord into the
TEL LINE jack. Route the cord
through the molded wiring channel
as shown.
6) Plug the telephone line cord into the
telephone outlet.
7) Align the mounting slots on the base
with the mounting posts on the wall.
Then push in and down until the
phone is firmly seated.
2
1
5
3
4
6
7
7
To remove, push up
a tab on the wall
mount adapter as
shown.
Uniden EXA3245.book 8 ページ ２００４年２月４日 水曜日 午後６時１８分

[9] GETTING STARTED www.uniden.com
Direct wall mounting
If you don't have a standard wall plate, you can mount your phone
directly to the wall. Before doing this, consider the following:
• Avoid electrical cables, pipes, or other items behind the
mounting location that could cause a hazard when inserting
screws into the wall.
• Try to mount your phone within 5 feet of a working phone jack
to avoid excessive cord lengths.
• Make sure the wall material is capable of supporting the weight
of the base and handset.
• Use #10 screws (minimum length of 1-3/8 inches) with
anchoring devices suitable for the wall material where the base
unit will be placed.
1) Insert two mounting screws into the wall, (with their
appropriate anchoring device), 3-15/16 inches apart. Allow
about 1/8 of an inch between the wall and screw heads for
mounting the phone.
2) Refer to steps 1 through 8 on page 8 to mount the telephone.
E. Choose the Dialing Mode
Most phone systems use tone dialing. However some phone systems (such as in rural areas)
still use pulse dialing. Your Uniden phone supports both tone and pulse dialing. The default
setting is tone dialing. If your phone system uses pulse dialing, follow the steps below to
change the dialing mode:
1) In standby mode, press and hold the remote key until you hear a confirmation tone.
2) Press the #key to set your phone for pulse dialing. You will hear a confirmation tone.
•If you are not sure of
your dialing system,
make a trial call. If the
call connects, leave
the setting as is.
Otherwise, set for
pulse dialing.
•If your phone system
requires pulse dialing
and you need to send
DTMF tones during a
call, you can
temporarily switch
over to tone dialing.
(Refer to “Tone Dialing
Switch-over” on
page 12).
note
GETTING STARTED
Uniden EXA3245.book 9 ページ ２００４年２月４日 水曜日 午後６時１８分