Uniden EXP920 User manual

C:\LaDonna\EXP920\Exp920e.vp
Tue Jun 23 16:28:39 1998
Color profile: Disabled
Composite Default screen

CONTENTS
OF YOUR OWNERS MANUAL
CONTENTS
Introduction......................................1
 Welcome ......................................1
 Exp 920 Features ................................1
 Included In Your Package .........................2
Setting Up .......................................3
 Desk Or Tabletop Installation.......................3
 Wall Installation.................................5
 Setting The Handset Retainer......................10
 Extending The Antenna ..........................11
 Installing The Beltclip ...........................12
 Removing The Beltclip ...........................12
 Installing The Handset Battery Pack ................13
 Charging The Battery Pack .......................14
 Low Battery Indicator ...........................15
 Cleaning The Battery Contacts.....................16
 Setting The Pulse-Tone Switch .....................16
 Adjusting Ringer Controls ........................17
 Automatic Digital Code Security....................18
Programming Your Exp 920.........................19
 Storing Memory Dial Numbers ....................19
 Storing Mixed Tone/pulse Numbers.................21
 Erasing A Stored Number ........................22
Standard Use ....................................23
 Answering A Call From The Base ..................23
 Answering A Call From The Handset ................23
 Making A Call From The Base ....................24
 Making A Call From The Handset ..................24
 Two-Line Operation.............................25
 Dialing Stored Numbers..........................25
 Chain Dialing..................................26
 Placing A Call On Hold ..........................26
 Using The Flash Button ..........................26
 Last Number Redial .............................27
 3-Way Conferencing.............................27
 Using Your Exp 920 Intercom .....................28
Troubleshooting .................................30
Specifications ....................................31
C:\LaDonna\EXP920\Exp920e.vp
Tue Jun 23 16:30:37 1998
Color profile: Disabled
Composite Default screen

WELCOME
Congratulations on your purchase of the Uniden EXP 920
Cordless Telephone. The EXP 920 is designed and engineered to
exacting standards for reliability, long life, and outstanding
performance. To get the most from your EXP 920, please read
this Owners Manual thoroughly. Refer to the foldout located in
the back of this Owners Manual to help familiarize you with the
features of your cordless phone. Also, be sure to fill out the
Product Registration card and mail it in.
EXP 920 FEATURES
•900 MHz Performance
•2-Line Operation
•Headset Compatible (optional headset model HS 900 B-C)
•Dual Keypad
•Speakerphone
•40 Channel Autoscan System
•20 Number Memory
•Page/Intercom System
•Redial
•Durable Belt Clip
•Desk or Wall Mountable
•Hearing Aid Compatible
AutoTalk allows you to answer a call by just removing the
handset from the base so you dont have to waste time pushing
buttons or flipping switches.
AutoStandby allows you hang up by simply returning the
handset to the Base.
UltraClear Plus virtually eliminates background noise and
provides you with the best possible reception during all of
your conversations.
Random Code digital security automatically selects one of
over 65,000 codes for the handset and base.
AutoSecure electronically locks your phone when the
handset is in the Base.
These features enhance your phones security and prevent
unauthorized calls as a result of your phone being actvated by
other equipment.
1
TO YOUR NEW PHONE
INTRODUCTION
INTRODUCTION
C:\LaDonna\EXP920\Exp920e.vp
Tue Jun 23 16:30:38 1998
Color profile: Disabled
Composite Default screen

INCLUDED IN YOUR PACKAGE
2
•This Owners Manual
•Other Printed Material
Battery
Base AC Adapter
Long Telephone Cord Short Telephone Cord
Belt Clip
Handset
WARNING
If any of these items are
missing or damaged,
contact the Uniden Parts
Department at
[phone], 8:00 a.m. to
5:00 p.m. Central, Monday
through Friday, or contact
us on the web at
www.uniden.com.
TIP
To get the most from your
phone, please read this
owners manual thoroughly.
Also, be sure to complete
and mail the product
registration form.
Wall Mount Stand
and Screws
Desktop Stand
C:\LaDonna\EXP920\Exp920e.vp
Tue Jun 23 16:30:42 1998
Color profile: Disabled
Composite Default screen

DESK OR TABLETOP INSTALLATION
▼With the Desktop Stand
1. Slide the desktop stand into
the notches at the top of the
base, then snap the bottom
into place.
2. Plug the AC Adapter cord
into the DC input jack on
the base.
3. Wrap the AC Adapter cord
around the strain relief
notch on the base.
4. Plug one end of the long
telephone cord into the
TEL LINE 1/2 jack on
the base.
3
AND ADJUSTING YOUR PHONE
SETTING UP
TIP
Before choosing a location
for your phone, read the
Installation Considerations
included in the Precautions
and Important Safety
Instructions brochure.
SETTING UP
C:\LaDonna\EXP920\Exp920e.vp
Tue Jun 23 16:30:44 1998
Color profile: Disabled
Composite Default screen

5. Plug the other end of the
cord into the telephone
jack on the wall.
6. Plug the AC Adapter into a standard 120V AC wall outlet.
Use of the desktop stand is optional. Simply follow steps 2
through 6 above to install your EXP 920 without it.
4
NOTE
Before you plug the other
end of the telephone cord
into the modular jack on the
wall, charge the battery.
Refer to Charging the
Battery Pack, page 14.
Use only the Uniden AC adapter supplied with this phone.
DO NOT use an outlet controlled by a wall switch.
C:\LaDonna\EXP920\Exp920e.vp
Tue Jun 23 16:30:45 1998
Color profile: Disabled
Composite Default screen

WALL INSTALLATION
▼Standard Wall Plate Mounting
These phones are designed to be mounted on a standard AT&T
or GTE wall plate.
1. Slide the wall mount stand
into the notches at the top
of the base, then snap the
bottom into place.
2. Plug the AC Adapter cord
into the DC input jack on
the base.
3. Wrap the AC Adapter cord
around the strain relief
notch on the base.
5
SETTING UP
TIP
Before choosing a location
for your phone, read the
Installation Considerations
included in the Precautions
and Important Safety
Instructions brochure.
CAUTION
Place the power cord so that
it does not create a trip
hazard or where it could
become chafed and create a
fire or electrical hazard.
C:\LaDonna\EXP920\Exp920e.vp
Tue Jun 23 16:30:46 1998
Color profile: Disabled
Composite Default screen

4. Place the AC Adapter cord
inside the molded channel.
5. Plug one end of the short
telephone cord into the
TEL LINE 1/2 jack on
the base.
6. Place the telephone cord
inside the molded channel
on the bottom of the base.
7. Plug the other end of the
telephone cord into the
modular jack on the wall.
6
NOTE
Before you plug the other
end of the telephone cord
into the modular jack on the
wall, charge the battery.
Refer to Charging the
Battery Pack, page 14.
C:\LaDonna\EXP920\Exp920e.vp
Tue Jun 23 16:30:47 1998
Color profile: Disabled
Composite Default screen

8. Place the base on the posts
of the wall plate and push
down until its
firmly seated.
9. Plug the AC Adapter into a standard 120V AC wall outlet.
▼Direct Wall Mounting
If you do not have a standard wall plate, you can mount your
phone directly on a wall. Before mounting your phone, consider
the following:
•Select a location away from electrical cables, pipes, or other
items behind the mounting location. Inserting screws into
areas such as this can be hazardous.
•Try to locate your phone within a reasonable distance (10 feet
or so) of a working phone jack. Remember, you are not
mounting to a wall plate with a pre-existing line installed.
•You may need another, longer phone line other than the one
supplied with your phone in order to reach from your
mounting location to the working phone jack.
•If the selected mounting area has no wooden support beams
directly behind it, you will need the appropriate anchoring
devices in order for the wall to properly support your phone.
1. Insert two mounting screws
into the wall, with their
appropriate anchoring
device, 315 16 inches apart.
Allow 316 of an inch between
the wall and screwheads for
mounting the phone.
7
SETTING UP
Use ONLY the Uniden AC adapter supplied with this phone
and DO NOT use an outlet controlled by a wall switch.
C:\LaDonna\EXP920\Exp920e.vp
Tue Jun 23 16:30:49 1998
Color profile: Disabled
Composite Default screen

2. Plug the AC Adapter cord
into the DC input jack on
the base.
3. Wrap the AC Adapter cord
around the strain relief on
the base.
4. Place the AC Adapter cord
inside the molded channel.
5. Plug one end of the long
telephone cord into the
TEL
LINE 1/2 jack on the base.
8
C:\LaDonna\EXP920\Exp920e.vp
Tue Jun 23 16:30:49 1998
Color profile: Disabled
Composite Default screen