Uniden XDECT R003 User manual

XDECT R003
Bluetooth®
For more exciting new products please visit our website:
Australia: www.uniden.com.au
New Zealand: www.uniden.co.nz

2
XDECT R003BT Accessory Handset
Owner's Manual
XDECT R003BT
accessory
handset and
charger
(with stand)
What's in the box?
Battery
cover
Rechargeable
battery pack (BT-694s)
Repeater/Charger
AC
adapter
(AAD-041S(M))
If any items are missing or damaged, contact your place of
purchase. Never use damaged products!
Need Help? Get answers at our website:
www.uniden.com.au for Australian model or www.uniden.co.nz
for New Zealand model.
Important Safety Instructions!
When using your telephone equipment, basic safety precautions should always be
followed to reduce the risk of re, electric shock and injury to persons, including the
following:
This unit is NOT waterproof.
DO NOT expose this unit to rain or moisture.
Do not use this product near water, for example, near a bath tub, wash bowl, kitchen

sink or laundry tub, in a wet basement or near a swimming pool.
Avoid using a telephone (other than a cordless type) during an electrical storm. There

may be a remote risk of electric shock from lightning.
Do not use the telephone to report a gas leak in the vicinity of the leak.

Use only the power cord and batteries indicated in this manual. Do not dispose of

batteries in a re. They may explode. Check with local codes for possible special
disposal instructions.
Do not place the handset in any charging cradle without the battery installed and the

battery cover securely in place.
SAVE THESE INSTRUCTIONS!

3
Setting Up Your Handset
Install the Battery
1. Unpack the handset, battery pack, and
battery cover. If the battery cover is
already on the handset, press in on the
notch and slide the cover down and off.
Line up the battery pack2.
connector with the jack inside the handset. (The battery connector
only fits one way.)
Push the battery pack connector in until it clicks into place. Tug3.
gently on the wires to make sure the battery pack is securely
connected.
Place the cover over the battery4.
compartment and slide it up into
place.
Connect the Charger
Connect the AC adapter to the charger's1.
DC IN 9V
jack and route the cord as
shown. (This adapter might already be
connected.)
Plug the other end of the adapter into a2.
standard 240V AC power outlet.

4
Place the handset in the charger with the display facing forward.3.
The display on the handset should turn on.
If... Try...
the display on the
handset does not turn
on
reseating the handset.-
checking the AC adapter-
connection.
Charge the handset completely (about 15 hours)
before using it.
Registering the Handset
The accessory handset will not work until you register it to
a base! Registering the handset is a separate process from
registering the Repeater/ charger. You can use the handset
normally even if the charger is not registered.
Compatible Bases
This handset is designed for use with Uniden's XDECT R035BT
base. For the most up-to-date list of compatible bases for this
handset, see our website.
Register the handset
Place the handset in the base. The display should say Handset
Registering .
After about 30 seconds, the handset display should say
Registration Complete .
Test the connection
Pick up the handset and press
TALK
. Make sure you get a dial tone.
(Press
END
to hang up.)
If... Try...
you don't hear a dial tone-
the display says-
Registration
Failed
Making sure the handset is fully charged,
then trying again.
To use your XDECT R003BT with your Bluetooth phones, see
the manual that came with XDECT R035BT base.

5
Using the Repeater/Charger
How it Works
The XDECT R003BT repeater/charger extends the range of your
base in all directions, including up and down. Each handset will
automatically connect to the repeater/charger or the base,
depending on which signal is stronger. (The handset operates
exactly the same way whether it's connected to the base or to the
repeater/charger.)
To use the charger's repeater function, you must register the

charger to an XDECT R035BT base. (Any repeater/chargers that
came packaged with the base are already registered to that base
for you.)
An XDECT R035BT base can support up to six XDECT R003BT

repeater/chargers, including any that were supplied with your
phone.
Usually, you can't tell when a handset switches between the

base and the repeater/charger in the middle of a call, but
sometimes, you might notice a brief pause in your conversation.
Repeaters can be up to 3 chain-links (maximum) from the base
Base Coverage Area
Handsets in this area always
connect to the base.
Overlap Coverage
Area
Handsets in this
area might connect
to the base or the
charger.
Extended Coverage Area
Handsets in this area
always connect to the
charger.
Base
Repeater/charger

6
Registering the Repeater/charger
Registering the Repeater/charger is a separate process from
registering the handset. You can use the charger even if the
handset is not registered.
On the base, press and hold1.
FIND
when the phone is in standby.
2. On the bottom of the repeater/charger,
press and hold the registration
button until the
LINK
light starts to
blink (about 2 seconds).
Release the button and wait for3.
the
LINK
light to turn on and steady
(this can take about 90 seconds).
If the
LINK
light doesn't
turn on,
disconnect
the charger's AC adapter. Wait about ten
seconds, then try these steps again.
Some important things to remember:
Only register one charger at a time. If more than one charger

is in registration mode at the same time, they can interfere with
each other.
If you want to use the repeater/charger with a different base, just

register the charger to the new base. The charger automatically
erases the link to the old base when it registers to the new one.
Only register chargers to one base at a time. If more than one

base is in registration mode at the same time, you can't control
which base the charger registers to.
Placing the repeater/charger
Here are a few tips for placing your repeater/charger so that you get
the clearest signal and the maximum range:
Make sure you have good reception from the base.

Put the charger
at least 10m away from the base or any other
charger. (If you put the charger on a different floor from the base,
don't forget to allow 10m vertically, also.)
If possible, mount the charger on the wall.


7
Picking the best spot
The best spot for the repeater/
charger is as far from the
base as possible while still
maintaining a good signal,
or near the edge of the
base’s coverage area. To
find the edge of the
coverage area:
Stand near the base1.
and make a call on the
handset.
While on the call, carry2.
the handset away
from the base towards the general area where you want to put the
charger.
Watch the signal strength icon on the handset. Make a note where3.
the icon drops from 4 bars to 3 bars.
Continue walking away from the base. Make a note where the signal4.
strength icon drops from 3 bars to 2 or if you start to hear noise on
the line (which indicates the signal is getting weaker).
Place the charger anywhere inside the range where the signal5.
strength icon showed 3 bars and the handset had a clear signal with
no noise.
Testing the location
Connect the charger's AC adapter and make sure the
LINK
light
comes on steadily. If the light flashes, the repeater/charger is not
getting a good signal from the base. The charger may be too far
away from the base, there may be interference from electronic
devices, or the signal might be blocked by thick walls or metal
objects. Try moving the charger to another location.

8
Wall Mounting the Repeater/charger
If you want mount the charger on the wall, you need to adjust the
desk stand:
Pull the locking tab up and1.
back (see the black arrow in the
illustration to the right), and slide
the desk stand straight off.
Flip the stand over so the locking2.
tabs that say
WALL
are facing the
charger with the arrows pointing
down.
3. Align the stand with the
notches on the charger.
Slide the stand onto the4.
notches until it clicks into
place.
Insert two #10 screws into the5.
wall, 30 mm apart. (For best
results, use a level to ensure
the screws are even.)
Remember to use
appropriate anchors for the
wall material.
Keeping the AC adapter cord6.
out of the way, place the
charger over the screw heads
and slide it down into place.
Switching back to the
desk stand
If you want to switch back to
using the charger on a desktop:
Remove the stand.1.
Rotate the stand so that the locking tabs that say2.
DESK
are facing
the charger with the arrows pointing up.
Align the stand with the notches on the charger.3.
Slide the stand onto the notches until it clicks into place.4.

9
Important Information
Handling Liquid Damage
Moisture and liquid can damage your cordless phone.
If the handset or repeater/charger is exposed to moisture or

liquid, but only the exterior plastic housing is affected, wipe off
the liquid, and use as normal.
If moisture or liquid has entered the plastic housing (i.e. liquid

can be heard in the phone or liquid has entered the handset
battery compartment or vent openings on the base), follow these
steps:
Handset Repeater/charger
Remove the battery cover and disconnect1.
the battery.
Let dry for at least 3 days with the battery2.
disconnected and the cover off for
ventilation.
After the handset dries, reconnect the battery3.
pack and replace the cover. Recharge the
battery fully (15-20 hours) before using.
Disconnect the AC adapter to cut off1.
the power.
Let dry for at least 3 days before2.
reconnecting.
IMPORTANT: You must unplug the telephone line while recharging
the battery pack to avoid charge interruption.
CAUTION! DO NOT use a microwave oven to speed up
the drying process. This will cause permanent damage
to the handset, base and the microwave oven.
Specications
Use only the supplied AC adapter.

Be sure to use the proper adapter for

the base and any chargers.
Do not place the power cord where it

creates a trip hazard or where it could
become chafed and create a re or
electrical hazard.
Do not place the unit in direct sunlight

or subject it to high temperatures.
AC
adapter
Part number AAD-041S(M)
Input voltage 240V AC, 50Hz
Output voltage 9V DC@ 350mA
Battery
pack
Part number BT-694s
Capacity 500mAh (BT-694s)

10
Battery Information
Fully charged, the battery should provide about 10 hours of talk time and about 7 days

of standby time. For best results, return the handset to the cradle after each call to
keep it fully charged.
Keep an eye on the battery status icon. When the battery gets too low, the handset

shows a low battery alert. If you hear a strange beep during a call, check the display:
if you see the low battery alert, nish your conversation as quickly as possible and
return the handset to the cradle. If the handset is in standby, none of the keys will
operate.
With normal use, the battery should last about one year. Replace the battery when

the talk time becomes short even when the battery is charged. To buy a replacement
battery, visit the website; www.uniden.com.au for Australian model or www.uniden.
co.nz for New Zealand model.
Rechargeable Nickel-Metal-Hydride Battery Warning
CAUTION! Risk of explosion if battery is replaced by an
incorrect type! Dispose of used batteries according to
the instructions. Do not open or mutilate the battery.
Disconnect the battery before shipping this product.
This equipment contains a rechargeable Nickel-Metal-Hydride battery.

The rechargeable batteries contained in this equipment may explode if disposed of in

a re.
Do not short-circuit the battery.

Do not charge the rechargeable battery pack used in this equipment with in any

charger other than the one designed to charge this battery pack as specied in the
owner's manual. Using another charger may damage the battery pack or cause the
battery pack to explode.
Rechargeable Batteries Must Be Recycled or Disposed of Properly.
Uniden works to reduce lead content in PVC coated cords in our products &
accessories.