Uniden App Cam 4K Bullet-S User manual

App Cam 4K
Dome
Quick Start Guide

What’s in the Box
1
Screw Kit
x1
1m Ethernet CableApp Cam 4K Dome
x1
Weatherproof Lid
x1
Quick Start Guide
x1
Mounting Template
x1
x1

2
General Introduction
NOTE:
out the camera included in the package and check out the details from
the correpsonding introduction above.
model of product.
NOTE:
out the camera included in the package and check out the details from
the correpsonding introduction above.
model of product.
Mount
Metal Case
Infrared Lights
Lens
Daylight Sensor
Built-in Mic
Weatherproof Lid
Ethernet Port
Reset Button
Power Port (Optional)
* Press and hold for 10 seconds to restore the
camera to factory settings

3
Camera Connection
Before using the camera, please connect the camera to App Cam 4K NVR.
Connection Diagram
DC4 8V
IN
AUDI O
OUTUSBHDMI VGA LAN
eSATA
1
2
3 5 7
4 6 8
9
10
11 13 1 5
12 14 1 6
ONOFFReset Button
DC Power
Network (LAN)
Note:
The camera should be powered with a Uniden App Cam 4K NVR (not included in the package).
Please set up the camera via the NVR interface.

Mount the Camera
4
Installation Tips
• Do not face the camera towards any light sources.
• Do not point the camera towards a glass window. Or, it may result in poor image quality
because of the window glare by infrared LEDs, ambient lights or status lights.
• Do not place the camera in a shaded area and point it towards a well-lit area. Or, it may
result in poor image quality. To ensure best image quality, the lighting condition for both
the camera and the capture object shall be the same.
• To ensure better image quality, it’s recommended to clean the lens with a soft cloth from
time to time.
• Make sure the power ports are not directly exposed to water or moisture and not blocked
by dirt or other elements.
• With IP weatherproof ratings, the camera can work properly under conditions like rain
and snow. However, it doesn’t mean the camera can work underwater.
• Do not install the camera at places where rain and snow can hit the lens directly.

5
Step 1
Drill holes in accordance with the
mounting hole template.
NOTE: Use the drywall anchors
included in the package if needed.
Installation Tips
1
2
2
1
3
4
Step 2
Install the mount base with the
mounting screws included in
the package.
NOTE: Run the cable through the
cable notch on the mount base.

6
Step 3
To get the best eld of view,
loosen the adjustment knob
on security mount and turn
the camera.
Step 4
Stiffen the adjustment knob to
lock the camera.
1
2
2
1
3
4

Camera is not turning on
If your camera is not powering on, please try the following solutions:
• Make sure your camera is powered properly. The camera should be powered by the Uniden App Cam 4K NVR
or a 12V power adapter.
• If the camera is connected to a PoE device as listed above, connect the camera to another PoE port and see
if the camera will power on.
• Try again with another Ethernet cable.
Infrared LEDs Stop Working
If the Infrared LEDs of your camera stop working, please try the following solutions:
• Enable infrared lights on Device Settings page via Uniden Solo App.
• Check if the Day/Night mode is enabled and set up auto infrared lights at night on Live View page via Uniden
Solo App.
• Upgrade the rmware of your camera to the latest version.
• Restore the camera to factory settings and check out the infrared light settings again.
If there are more support needed, please contact Uniden Support.
Troubleshooting
7

Video & Audio
Model App Cam 4K Dome
Image Sensor 1/2.49” CMOS Sensor
Video Resolution up to 3840x2160 (8MP) 4K up to 25 fps
Video Compression H.264/H.265
Viewing Angle Horizontal: 87° Vertical: 44°
Night Vision Up to 30 Meters
Audio Two-way talk
Alerts Person detection; vehicle detection; motion detection
Network Ethernet One 10M/100Mbps; RJ45
Hardware
PoE IEEE 802.3af
DC Power Can be powerd by 12V/1A power adaptor
Storage Supports up to 256GB micro SD card, min class 10*
Other
Parameters
Temperature Operating Temperature : -10°C~+55°C
Operating Humidity 10% to 90%
Waterproof Level IP66 Weatherproof
Specications
8
*Note: When the camera is connected to the NVR, the SD Card storage option is not supported on the App
and the NVR itself. Only supports recording to fat32 SD Card when setup as a standalone camera.

Uniden App Cam 4K Dome
Terms of Warranty: Uniden Aust warrants to the original retail purchaser only that the Uniden App Cam 4K Dome
(“the Product”), will be free from defects in materials and craftsmanship for the duration of the warranty period,
subject to the limitations and exclusions set out below.
Warranty Period: This warranty to the original retail purchaser is only valid in the original country of purchase for a
Product first purchased either in Australia or New Zealand and will expire, as indicated below, from the date of original
retail sale.
Product 1 Year
Accessories 90 Days
If a warranty claim is made, this warranty will not apply if the Product is found by Uniden to be:
A. Damaged or not maintained in a reasonable manner or as recommended in the relevant Owner’s Manual;
B. Modified, altered or used as part of any conversion kits, subassemblies or any configurations not sold by Uniden
Aust;
C. Improperly installed contrary to instructions contained in the relevant Owner’s Manual
D. Repaired by someone other than an authorized Uniden Repair Agent in relation to a defect or malfunction
covered by this warranty; or
E. Used in conjunction with any equipment, parts or a system not manufactured by Uniden.
Important:
Satisfactory evidence of the original purchase is required for warranty service. Please refer to our Uniden
website for any details or warranty durations offered in addition to those contained below.
Warrantor:
The warrantor is Uniden Australia Pty Limited ABN 58 001 865 498 (“Uniden Aust”).
WARRANTY