CABLE
H
E
L
P
INFO future use
displays help for on-screen
display screens
switches between cable TV and
Music ChoiceTM
exits the on-screen display menus
displays the main on-screen display
menu
initiates VCR recording through the
on-screen menu (if so equipped)
pages through on-screen menu and
program guide screens
displays the quick function screen
recalls the last channel that was
viewed
indicates remote control activity
future use
MOVIES future use
FAV cycles through your favorite channels
INFO displays channel and program information
GUIDE displays the program guide
SEL selects options from the program guide and
be used to set up the remote.
CURSOR KEYS navigate through on-screen guides
TV/VCR switches between control of
your TV and your VCR
VCR/DVD KEYS perform standard VCR and DVD
functions when in VCR mode.
DAY +/
-
moves the program guide one day
forward and backward
MUTE turns volume off
Install two
AAA alkaline batteries
as shown here
changes the channel up and down
allow you to turn on and off your TV,
VCR, and CABLE box. They are also used to setup the
remote control
turns the volume up and down
allow direct access to
specific channels and
menu options
SEL
Button Functions
3
Programming the Remote Control.
5
A. Three-Digit Code Programming Method.
The remote control can be programmed by pressing in a three digit code number that
corresponds to particular manufacturers and brands of Audio/Video equipment.
The three-digit code numbers are listed in the code table of the instruction manual.
STEP1 Turn on the equipment you wish to program. (TV, VCR, or DVD)
STEP2 Press the [DEVICE] button (TV POWER or VCR POWER) to be programmed and the
[SEL] button simultaneously for 3 seconds. The LED will turn on indicating the unit is
ready to be programmed.
*Tip : The LED will stay lit for 20 seconds. The next step must be entered while the LED is on.
STEP3 Point the remote control toward the equipment and enter the three-digit code number
assigned to your brand from the code tables.
*Tip : The equipment will turn off when the
correct three-digit code number has
been entered. You can verify you
have selected the correct code by
pressing the [MUTE] button, the
equipment should turn on or turn off.
*Note : If there is more than one three-digit
number listed for your brand, try
one code number at a time until
your equipment turns off.
STEP4 Store the three-digit code number
by pressing the same [DEVICE]
button once again. The LED will
blink twice to confirm that the code
has been stored.
*Note : Try all the functions on the remote
control. If any of the functions do
not work as they should, repeat from
Step 2 using the next three-digit code
number from the same brand list.
B. Auto Search Method.
If the three-digit code numbers assigned to
your brand do not turn off your equipment or
the code tables do not list your brand, you
can use the Auto Search Method to find the
correct three-digit code number for your
equipment by the following steps:
STEP1
Turn on the equipment you wish
to operate.
STEP2 Press the [DEVICE] button (TV
POWER or VCR POWER) to be
programmed and the [SEL] button
simultaneously for 3 seconds. The
LED will turn on.
*Tip : The LED will light on for 20 seconds. The
next step must be entered while LED is on.
STEP3 Point the remote control toward the
equipment and alternately press
the [CH+] (or [CH-]) button and the
[MUTE] button. If the right code
number is sent, the equipment will
turn off.
*Tip : You can verify that you selected the
correct code by pressing the [MUTE]
button again. The equipment should
either turn on or turn off.
STEP4 Press the same [DEVICE] button
to store the code. The LED will
blink twice to confirm that the
code has been stored.
C. To Find the Three Digit Code
Number That was Stored in the
Device.
STEP1 Press the [DEVICE] button (TV
POWER or VCR POWER) you wish
to verify and the [SEL] button
simultaneously for 3 seconds.
*Tip : The LED will turn on for 20 seconds.
The next step must be entered while
the LED is on.
STEP2 Press the [INFO] button.
The LED will blink number of times
indicating the number of each digit of the
code number. Each digit is separated by a 1
second interval of the LED being turned off.
Example : One blink, three blinks and
eight blinks with an interval of 1
second of LED being turned off,
indicates the code number 138.
Note : Ten blinks is equal to the number 0.
D. Programming a second TV to
VCR Mode.
STEP1
Press the [VCR POWER] button to
be programmed and the [SEL]
button simultaneously for 3
seconds.
*Tip : The LED will turn on for 20
seconds. The next step must be
entered while the LED is on.
STEP2 Press the [TV POWER] button
to pick up the TV code table.
STEP3 Point the remote control
toward the equipment and
enter the three-digit code
number assigned to your TV
brand from the code tables.
STEP4 Store the three-digit code
number by pressing the [VCR
POWER] button once again.
The LED will blink twice to
confirm that the code has been
stored.
E. Volume Punch Through:
By following the steps below, the user can
program the volume controls (Volume UP,
Volume Down and MUTE) from one device
to operate in another device mode.
The default volume control settings on the
remote control is TV volume control. If you
wish to store the CABLE volume control in
CBL mode, use the following steps.
STEP1 Press the [CABLE POWER]
button and the [SEL] button
simultaneously for 3 seconds.
*Tip : The LED will light on for 20
seconds. The next step must be
entered while the LED is on.
STEP2 Press the [VOL +] button.
STEP3 Press the [CABLE POWER]
button. The LED will blink twice
to confirm the programming.
To return to original state:
If you wish to restore the TV volume
control in CBL mode, repeat the above
steps by pressing [TV POWER] in step 3.
F. LOW BATTERY WARNING:
When the battery is low (2.0V-2.3V) and
needs to be replaced with fresh
batteries, the LED will blink twice
whenever a device [POWER] button is
pressed to turn on equipment.
G. Memory Lock System:
This remote control is designed to retain
programmed memory for 10 years even
after batteries are removed from the
remote control