Uniwell LX-5600 Owner's manual

2004-12-2
LX-5000series 02 type
LX-5600 2-sheet dot matrix printer
LX-5700 2-sheet thermal printer
LX-5750 1-sheet thermal printer
Programming /
Manual /"
CAUTION!
When the control key position is LOCK, the display is
off and keyboard is disabled but the ECR's power is still
ON. So that before you open the upper case, make sure
that the AC cord is disconnected. Especially when you
replace the ROM, it must be disconnected, otherwise the
ECR will be damaged.

CONTENTS OF PROGRAMMING MANUAL
I. BEFORE INSTALLATION.......................................................................................................... 1
II. INTRODUCTION.......................................................................................................................... 2
III. SPECIFICATIONS....................................................................................................................... 3
SYSTEM CONFIGURATION ........................................................................................................................5
RAM BOARD EXPANSION..........................................................................................................................6
OPTIONS.........................................................................................................................................................6
SET-UP OF PERIPHERALS...........................................................................................................................6
IV. STANDARD KEY LAYOUT....................................................................................................... 7
V. PROGRAMMING......................................................................................................................... 9
KEYBOARD PROGRAMMING ..................................................................................................................10
(SP-101) KEY LAYOUT ...................................................................................................................................... 10
PLU & GROUP PROGRAMMING ..............................................................................................................13
(SP-201/4201) PLU CODE.................................................................................................................................... 13
(SP-203/4203) PLU LINK TO GROUP ................................................................................................................ 14
(Z1/P-5302) PLU NAME & PRICE...................................................................................................................... 16
(Z1/P-305/4305) PLU PRICE................................................................................................................................ 16
(Z1/P-320/4320) PLU HALO (High Amount Lock-Out)...................................................................................... 17
(SP-200/4200) PLU FUNCTION FLAG............................................................................................................... 18
(SP-204) PLU LINK TO ONE PLU/LOOK UP PLU KEY .................................................................................. 21
(SP-209/4209) PLU LINK TO SUPPLEMENTARY MESSAGE......................................................................... 22
(SP-223/4223) GROUP-A LINK TO MAIN GROUP-A....................................................................................... 23
(SP-109) PLU MODIFIER VALUE...................................................................................................................... 23
(SP-111) MENU LAYOUT................................................................................................................................... 24
(SP-4111) MENU LAYOUT COPY PROCEDURE............................................................................................. 24
(Z2-406) PLU STOCK .......................................................................................................................................... 25
(Z2-426) GROUP-A STOCK ................................................................................................................................ 26
(SP-127) TARE TABLE........................................................................................................................................ 26
(SP-5201) COMPLETE PLU PROGRAMMING.................................................................................................. 27
LOOK UP PLU PROGRAMMING...............................................................................................................28
(SP-504) LOOK UP PLU ASSIGNMENT............................................................................................................ 28
(SP-500) LOOK UP PLU FUNCTION ................................................................................................................. 29
(SP-509) LOOK UP PLU MENU SHIFT VALUE ............................................................................................... 30
(SP-5502) COMPLETE LOOK UP PLU PROGRAMMING................................................................................31
CHARACTER PROGRAMMING ................................................................................................................32
(SP-212) CLERK NAME ...................................................................................................................................... 32
(SP-152) ECR NAME, KITCHEN PRINTER NAME.......................................................................................... 32
(SP-222) GROUP-A NAME.................................................................................................................................. 32
(SP-232) GROUP-B NAME.................................................................................................................................. 32
(SP-102) KEY/SYMBOL NAME.......................................................................................................................... 32
(SP-502) LOOK UP PLU NAME.......................................................................................................................... 32
(SP-242) MAIN GROUP-A NAME...................................................................................................................... 32
(SP-252) MEDIA NAME ...................................................................................................................................... 32
(SP-262) MEDIA CURRENCY SYMBOL........................................................................................................... 32
(SP-202) PLU NAME............................................................................................................................................ 32
(SP-122) RECEIPT/TICKET LOGO, CHECK-OUT BILL HEADER, TICKET HEADERS.............................. 32
(SP-162) SLIP/VALIDATION LOGO.................................................................................................................. 32
(SP-112) STOCK UNIT NAME............................................................................................................................ 32
(SP-142) SUPPLEMENTARY MESSAGE........................................................................................................... 32
(SP-182) WARNING MESSAGE ......................................................................................................................... 32
(SP-131) CHARACTER KEY LAYOUT FOR SETTING NAMES..................................................................... 39
RATE PROGRAMMING..............................................................................................................................41
(Z1/P-337) PERCENTAGE RATE........................................................................................................................ 41
(Z1/P-347) ADJUSTMENT RATE ....................................................................................................................... 41
(Z1/P-357) SALES COMMISSION RATE........................................................................................................... 41
(Z1/P-367) STOCK RATE .................................................................................................................................... 41
(Z1/P-387) FOREIGN CURRENCY EXCHANGE RATE................................................................................... 41
(Z1/P-377) CHEQUE-CASHING CHARGE RATE / CURRENCY EXCHANGE CHARGE RATE ................. 42
(Z1/P-397) EURO CURRENCY RATE................................................................................................................ 42
(SP-107) TAX RATE ............................................................................................................................................ 43

(SP-108) TAX EXEMPTION LIMIT FOR % TAX / TAX TABLE FOR ADD-ON TAX SYSTEM.................. 43
MEDIA PROGRAMMING ...........................................................................................................................46
(SP-253) PRESET TENDER KEY LINK TO MEDIA ......................................................................................... 46
(Z1/P-315) PRESET TENDER AMOUNT ........................................................................................................... 47
(SP-110) MEDIA FUNCTION.............................................................................................................................. 48
CLERK PROGRAMMING ...........................................................................................................................51
(SP-211) SECRET CLERK CODE ....................................................................................................................... 51
(SP-214) CLERK 20 PLU/GROUP-A ASSIGNMENT ........................................................................................ 51
(SP-213) CLERK LINK TO iBUTTON................................................................................................................ 52
(SP-219) CLERK LINK TO HARD CLERK KEY............................................................................................... 52
(SP-210) CLERK SECURITY FUNCTION.......................................................................................................... 53
MISCELLANEOUS PROGRAMMING .......................................................................................................54
(SP-151) TRAINING SECRET CODE ................................................................................................................. 54
(SP-171) MACHINE NUMBER ........................................................................................................................... 54
(SP-179) SLIP PRINTER ID # FOR TP-620......................................................................................................... 54
(SP-191) EFT TERMINAL PASSWORD............................................................................................................. 54
(Z1/P-325) + / - AMOUNT.................................................................................................................................... 54
(SP-172) TERMINAL ADDRESS ........................................................................................................................ 54
(SP-121) ARRANGEMENT KEY SEQUENCE................................................................................................... 55
(SP-189) CHEQUE PRINTING FORMAT........................................................................................................... 56
TIME & DATE PROGRAMMING...............................................................................................................58
(X-1) DATE........................................................................................................................................................... 58
(X-2) TIME............................................................................................................................................................ 58
SYSTEM PROGRAMMING.........................................................................................................................59
(SP-100) SYSTEM FUNCTION........................................................................................................................... 59
PROGRAMMING REFERENCE..................................................................................................................95
VI. REPORTS.................................................................................................................................. 100
REPORT SEQUENCE.................................................................................................................................100
IRC REPORT SEQUENCE.........................................................................................................................104
PROGRAM DUMP CONTENTS................................................................................................................106
VII. SERVICE PROGRAMMING.................................................................................................. 112
INITIAL RESET..........................................................................................................................................112
TEST PROGRAMS .....................................................................................................................................113
RAM TEST SP-9901............................................................................................................................................ 113
PHYSICAL RAM TEST ...................................................................................................................................... 114
ROM TEST SP-9902............................................................................................................................................ 114
PLU DATA ERASE SP-289 ................................................................................................................................ 114
TEST PRINT SP-9909.......................................................................................................................................... 114
HARDWARE TEST SP-9998/9999..................................................................................................................... 115
AUTO PRESET...........................................................................................................................................119
IRC PROGRAM DATA TRANSFER.........................................................................................................121
VIII. WARNING MESSAGES.................................................................................................... 122
IX. IRC MESSAGES....................................................................................................................... 126

CONTENTS OF INTERFACES & PERIPHERALS MANUAL
(This manual is independent from the programming manual.)
I. INTERFACE INFORMATION
II. IRC SYSTEM
III. PERIPHERALS
1. TERMINAL PRINTERS
1) TP-822/832 (Kitchen Printer, connected to ch-A)
2) TP-620 (Slip Printer, connected to ch-A)
3) CBM-1000 (Thermal Kitchen Printer, connected to ch-A via NA-710/730)
4) TM-T88III (Thermal Slip Printer, connected to ch-B)
2. SCANNER
3. SCALE
1) Scale Information of ICL Protocol [SF-25.a=0]
2) Scale Information of W Protocol [SF-25.a=1]
4. EFT TERMINALS
IV. PC COMMUNICATION
1. BATCH COMMUNICATION
2. PROGRAM LOADER (PLM 2000)
3. ESF DATA TRANSFER (Electronic Store & Forward)
V. ECR TO ECR RAM DATA TRANSFER
VI. JOURNAL DATA TRANSFER
VII. CABLE CONNECTION
1. CHANNEL A --- IRC LINE
2. CHANNELS B, D & E
1) ECR (ch-B) to Thermal Slip Printer TM-T88III
2) ECR (ch-B, ch-D/E) to Scale
3) ECR (ch-B, ch-D/E) to PC
4) ECR (ch-B, ch-D/E) to Handy Scanner
5) ECR (ch-B, ch-D/E) to Flat Bed Scanner
6) ECR (ch-B, ch-D/E) to Peripheral for Journal Data Transfer
7) ECR (ch-B) to ECR (ch-B) for RAM Data Transfer
8) ECR (ch-B) to EFT Terminal

1
I. BEFORE INSTALLATION
1. Power Supply
Use specified power supply. Do not connect with other machines which may cause electricity line noise.
2. Battery Charge
A battery is installed in ECR in order to maintain registration and programming contents for about 3 months. If
it has been discharged during transportation, the battery should be recharged before use. (Just plug in ECR and
leave it for one day.) Then, perform Auto Preset sequence. Refer to the section "Service Programming" (page
119).
3. Place of Installation
ECR should not be installed in extremely hot or cold environments, places exposed to direct sunlight for
extended period of time, or places where ECR may come into direct contact with excessive dust or liquid.
4. Installation of IRC Line
All terminals should be connected to AC power supplies placed on the same ground level. If some of the
terminals are connected to other AC line, electric potential difference on the ground line will damage the
interface boards and cause a communication error.
Termination resistors should be attached as described in the Interfaces & Peripherals manual so that the
communication error may be solved. The shielded cable must be used for IRC line.
Do not connect/disconnect the cable while ECR's AC cord is plugged.