UpDown Desk PRO Series Setup guide

PRO Series Complete Guide to Simple
Setup and Operation
Corner Desk

2
Table of Contents
Contents
Introduction 4
Pro-Series Corner Desk Frame Assembly 5
2.1. Contents 5
2.2 A note about screws/bolts 6
2.3 Step 1 8
2.3 Step 2 9
2.3 Step 3 10
2.3 Step 4 11
2.3 Step 5 13
2.3 Step 6 14
2.3 Step 7 16
2.3 Step 8 17
2.3 Step 9 19
2.3 Step 10 20
2.4 Desktops Installation 22
2.5 Control Panel Installation 27
2.6 Cable Tray Installation (Optional extra) 29
2.7 Control Panel Operation 30
2.8 Troubleshooting 34
2.9 Packaging recycling and disposal 35

3
Introduction
Congratulations on the purchase of your Pro-Series UpDown Corner Desk! You’ve made a significant
investment into your health and wellbeing and your body will thank you for it.
This instructional manual will guide you smoothly through the process of assembling the frame,
attaching the optional cable tray and installing the desktops with the control panel.
Required tools:
-Philips head screwdriver
-Measuring tape
Optional tools (to simplify desktop installations):
-Power drill
-2.5mm drill bit

4
Pro-Series Corner Desk Frame Assembly
2.1. Contents
1. 2 x regular feet
2. 1 x short corner foot
3. 2 x joining bars
4. 2 x pivot plates
5. 3 x legs
6. 1 x short corner wing
7. 2 x regular wings
8. 4 x spreader bars
9. 1 x control panel
10. 1 x control box
11. 1 x power cable
12. 2 x short motor cables (inc 1 spare)
13. 1 x medium motor cable
14. 1 x long motor cable

5
2.2 A note about screws/bolts
2 bags of bolts/screws are also contained within the corner desk boxes. Bag 1 is a generic package
covering several desk models whilst Bag 2 is specific to the corner desk. There may be some unused
bolts/screws once assembly/installation is complete.
M8 x 20mm
-12 pieces in total
-Allen key required (supplied)
-Used to attach feet to the legs
M6 x 10mm
-4 pieces in total
-Philips head screwdriver required (not supplied)
-Used to attach the control box to the adjustable tubes
M8 x 10mm
-22 pieces in total

6
-Allen key required (supplied)
-Used to attach the legs to the wings/spreader bar, used to attached spreader bars to pivot
plates.
Self tapping screws
-22 pieces in total
-Philips head screwdriver required (not supplied). Power drill optional (not supplied)
-Used to attach the frame, control panel and optional cable tray to the desktop(s)

7
2.3 Step 1
Note: The frame is being assembled upside-down initially as this is the simplest method.
In this step you will be using:
-2 x spreader bars
-2 x legs
-1 x regular wing
-1 x regular foot
-1 x short corner wing
-1 x short corner foot
-2 x pivot plates
Arrange the parts as shown, ensuring the spreader bar control box tabs face inwards and the
desktop connector tabs facing outwards. Both sets of tabs should be adjacent to the ground as
shown above.

8
2.3 Step 2
Using the Allen key provided, loosen (do not remove) the 8 pre-installed grub screws of the
spreader bars as indicated below. The bars should be able to slide relatively freely.

9
2.3 Step 3
Install the first leg onto the spreader bars and regular wing using 6 x M8x10mm screws

10
2.3 Step 4
Moving to the second leg, install the pivot plates as shown using 3 x M8x10mm screws per pivot
plate.
Important: Each pivot plate has a step and must only be installed exactly as shown.

11
The short corner wing can now be installed use 2 x M8 x 10mm screws

12
2.3 Step 5
Install the pivot plate to the spreader bars using the holes as shown using 2 x M8x10mm screws. Do
NOT tighten; the spreader bar must be able to pivot within the pivot plate slot at this point.

13
2.3 Step 6
Attached both feet. The short foot uses 2 x M8x20mm screws and the regular foot uses 4 x
M8x20mm screws.
Flip the assembly over and position it as close as possible to its final desired location.

14
In preparation for the next steps, it’s advisable to ensure the pivot-plate-to-spreader-bar angle is
approximately 90 degrees as shown below.

15
2.3 Step 7
Assembly of the 3rd leg can now take place. In the same manner as Step 2 from earlier, ensure the
spreader bar tabs are correctly positioned and adjacent to the ground.
oLoosen (do not remove) 8 grub screws
oAssemble spreader bar and regular wing onto the leg using 6 x M8x10mm screws
oAssemble regular foot onto the leg using 4 x M8x20mm screws
-

16
2.3 Step 8
Flip the 3rd leg assembly and rest the spreaders bars on the pivot plate as shown.
Accessing the frame from underneath, connect the spreader bar to the pivot plate using 2 x
M8x10mm screws. Do not tighten at this point; the spreader bar should be able to pivot within the
pivot plate slot.

17
Once again, keep the spreader bar pivot plate of the 3rd leg assembly at approximately 90 degrees
as shown below.

18
2.3 Step 9
At this point it is necessary to determine where the control panel will go as this dictates the side the
control box is mounted to. The control box should be mounted on the side closest to the future
control panel location. Control panel location is entirely personal preference. Install the control box
to the spreader bar tabs as shown using 4 x M6x10mm screws.

19
2.3 Step 10
Install all cables. The short cable connects the control box to the closest motor, medium cable to
the middle leg motor and long cable to the farthest leg. To assist with cable management later, it’s
useful to run the long cable behind the middle motor as shown. Final cable management will occur
later once the desktops have been installed. Install the power cable and control panel cable into the
control box.

20
Plug the power cable into a 240v power source. The frame should now be operational. It’s useful to
elevate the frame to a workable height that suits you for installing the desktops as you will need to
work underneath the desk.