Uplift Desk ACC304 User manual

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
®
Horizon™ Monitor Arm Instructions
ACC304
Clamp Step 2
Screw the Clamp bolt (part 13) up from the bottom of the Clamp bracket,
and insert the Clamp plate (part 12) into the tab at the tip of the Clamp Bolt.
Clamp Step 1
Slide the Outer Wire clip (part 14) into the back notch of the Arm’s base.
Attach the Clamp bracket (part 11) to the Arm’s base with the four M6*12
screws (part 4). Secure the screws with the medium Allen wrench
(part 6).
Clamp Step 3
Apply the Clamp gasket (part 15) under the Arm’s base.
Match the holes in the gasket to where the placement of the screws are.
Clamp Step 4
Slide the assembly onto your desk, and turn the Clamp bolt to tighten
and afx to desk.
Part 1
UPLIFT Horizon™ arm
Part 4
M6*12 screw
(qty 4)
Part 3
Washer
(qty 2)
Part 7
Allen wrench
(large)
Part 11
Clamp bracket
Part 8
Boxed wrench
Part 12
Clamp plate
Part 9
Cable cover 1
Part 13
Clamp bolt
Part 10
Cable cover 2
Part 14
Outer wire clip
Part 15
Clamp gasket
Part 16
Bolt plate
Part 17
Bolt assembly
Part 18
Open-end wrench
Part 19
Nut
Part 20
Inner wire clip
Part 21
Bolt gasket
Part 2
M4*12 screw
(qty 4)
Part 5
Allen wrench
(small)
Part 6
Allen wrench
(medium)
Clamp Assembly - Attach the arm to the back of the desk. Clamp will t desks up to 1.7’’
Step 1
Attach arm to desktop.
There are two ways to attach your UPLIFT Horizon™ Monitor Arm to your desktop: Clamp and Bolt-through assembly.
ACC304/R01

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
Step 2
Use the small Allen wrench (part 5) to insert two M4*12 screws (part 2)
into the top two holes on the back of your monitor (see gure 1).
Do not screw them in all the way. Leave some space as shown.
Step 3
Place the monitor onto the open holes on the VESA plate on the arm.
See gure 2 for specic placement. Let the monitor hang from the two
screws.
Fig. 1
Fig. 2
Fig. 3
Step 4
Screw in two M4*12 screws (part 2) and two washers (part 3), into the
lower holes on the VESA mounting plate (see gure 3) and tighten.
When nished, tighten all screws from step 2.
Bolt-Through Assembly - Will work with holes from .4’’ to 3.14’’ in diameter, and desks up to 2’’ thick.
Bolt-Through Step 1
Slide the Inner wire clip (part 20) into the back notch of the Arm’s base.
Next, take the Bolt assembly (part 17) and attach it to the underside of
the Arm’s base with the four M6*12 screws (part 4), and tighten with the
medium Allen wrench (part 6).
Bolt-Through Step 2
Apply the Bolt Gasket (part 21) under the Arm’s base, sliding
the bolt through the gasket’s center hole.
Bolt-Through Step 3
On the underside of the desk, place the Bolt plate (part 16) around
the bolt, and screw on the nut (part 19). Use the Open-end wrench (part 18)
to tighten and secure the Monitor arm.

© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
Step 6
If you attached the arm to your desk using the Clamp method,
you can run your wires down the back into the Outer wire clip.
If you attached the arm by the Bolt-through method, and the grommet
hole is wide enough, you can run your wires through the Inner wire clip.
Step 7
Now that your monitor is attached to the arm, and the arm is on your
desk, try moving the monitor around a bit, and then let it go. Does the
monitor stay put after you let it go, or does it rise upward or drift down?
If so, you may need to adjust the counterbalance.
To adjust counterbalance, use the large Allen wrench (part 7) and insert
it into the hex slot at the hinge of the lower and upper arm.
Turning clockwise will reduce the tension for lighter monitors. Turning
counterclockwise will increase the tension so the arm can lift heavier
monitors more easily. This may take several turns.
The goal is to get the counterbalance positioned to where you can move
the monitor to any height, and for the arm to hold it at that placement.
Step 8
You can adjust the forward and backward tilt of your monitor.
First, remove the plastic cover on the VESA mount hinge.
Use the Boxed wrench (part 8) to adjust the bolt if needed. Loosen it up
enough so that you can tilt the monitor downward or upward. When you
get it to a position you like, tighten the bolt and replace the plastic cover.
Refer to the illustrations to the left to complete the installation of Cable
cover 1 and Cable cover 2. Both covers should be completely secure be-
fore moving on to Step 6.
Step 5
Plug your cables into your monitor. Use the Cable covers (parts 9 & 10)
to hold the monitor’s cables along the underside of the arm. Use Cable
cover 1 (part 9) on the upper part of the arm, and Cable cover 2 (part 10)
on the lower part of the arm.
Leave some slack in the cables near the joints to allow the arm room
to adjust.
Cable cover 1
Cable cover 2
Cable cover 2Cable cover 1

CAUTION
!
Copyright Notice: These instructions are a component of the UPLIFT Horizon ™ Monitor Arm . These instructions are part of the scope of delivery, even if the item is
resold. These instructions are also available on the UPLIFT Desk website: upliftdesk.com. Excerpts or copies may not be forwarded to third parties or used in any other
published form without the prior written consent of UPLIFT Desk.
These instructions are subject to United States copyright law.
©
•
•
•
NOT A CHILD’S TOY. Children under 12 must
be supervised by an adult while using UPLIFT Hori-
zon™arm.
Failing to follow these assembly instructions
and safety precautions may result in personal injury.
Failing to follow these assembly instructions
and safety precautions voids your warranty
and may result in property damage.
•
•
•
The maximum load capacity of the UPLIFT Hori-
zon™monitor arm is 18.7 lbs. Do not overload.
Leave cables near the joints of the wire manage-
ment slack to allow the arm room to adjust.
Secure all clamps and mounts to a stable desktop.
360°
8.6’’
360°
180°
90°
30°
360°
UPLIFT Horizon™ Monitor Arm adjustability