Uplift Desk Crestview MON032 User manual

© UPLIFT Desk • 800-349-3839 • [email protected] • upliftdesk.com
Package Contents
Crestview Dual Monitor Arm
SKU: MON010-2, MON032
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
1
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Package Contents
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
Allen Wrenches
(set of three: 3mm, 4mm, 6mm) Part for
Bolt-through assembly
Lower Arm
(qty 2)
Wire Cover
Upper Arm
(qty 2)
Lower Clamp
VESA Plate
(qty 2)
Adhesive Pad
Upper Base Plate
Upper Clamp
M5x12 Screw (M-B) (qty 8)
M5 Washer (M-C) (qty 8)
M4x12 Screw (M-A) (qty 8)
M6x12 Flathead Screw (qty 4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Lower Base Plate
Base
Clamp Base Bolt-Through Base
Note: ACCEPTABLE MONITOR WEIGHT RANGE IS 2.2 to 33 lb. (per monitor)
Step 1
If you purchased the Crestview Monitor Arm Wiring
Kit, assemble that FIRST, before proceeding. Refer to
the separate instructions contained in the Crestview
Monitor Arm Wiring Kit (ACC076) package for com-
plete details.
Step 2
There are two ways to attach the Crestview Dual Mon-
itor Arm to your desktop.
If you would like to attach the monitor arm along the
back edge of your desktop, follow the Clamp Base
Assembly instructions (Step 2.1 - 2.3) and ensure your
desk is between 0.4” and 3.3” thick.
If you prefer to attach the monitor arm through your
desktop, follow the Bolt-Through Base Assembly in-
structions (Step 2.4 - 2.7) and ensure your desk is be-
tween 0.4” and 1.8” thick.
Step 2.1 - Clamp Base - only complete steps 2.1 to
2.3 if clamping the monitor arm to the edge of your
desktop. There is also a Bolt-Through option that
starts on step 2.4.
Align the Upper Clamp with the Base in the orienta-
tion shown. Attach using four M6x12 Flathead Screws
and the 4mm Allen Wrench.
Then peel the adhesive backing off of the Adhesive
Pad and attach it to the bottom of the Base and Upper
Clamp as shown. Align the pad with the front edge of
the Base rst, then work to the back.

© UPLIFT Desk • 800-349-3839 • [email protected] • upliftdesk.com2
Step 2.3 - Clamp Base
Using the 6mm Allen Wrench, adjust both bolts on
the bottom of the Lower Clamp so that the opening
is wide enough to accommodate the thickness of the
desktop and Lower Base Plate.
Place the outer holes of the Lower Base Plate onto the
tips of the bolts as shown.
Slide the assembly onto the back of the desktop, then
tighten the bolts using the 6mm Allen Wrench. Alter-
nate from one bolt to the other, to allow the Lower
Base Plate to rise evenly before nally tightening to
the desktop.
Step 2.2 - Clamp Base
Use the 4mm Allen Wrench to adjust the four pre-in-
stalled screws on the back of the Lower Clamp so that
there are about 0.25” of thread between the plate and
screw heads.
There are two sets of key slot holes to choose from for
different desktop thicknesses.
For Desks 0.4’’ to 2.25’’ use the top four holes (g. 1)
For Desks 2’’ to 3.3’’ use the bottom four holes (g. 2)
Insert the four screws of the Lower Clamp through
four of the key slot holes in the back of the Upper
Clamp as shown.
Slide the Lower Clamp assembly down so that the
screws are at the bottom of the key slot holes then
tighten screws with 4mm Allen Wrench.
g. 2g. 1
0.25”
6mm
0.24”
6mm
0.24”
6mm
Optional “Bolt-Through Base” Assembly
Only complete steps 2.4 to 2.7 if you are not going to clamp the monitor arm to the desktop.
Optional Step 2.4 - Bolt-Through Base
Important: You will need one or two holes per the siz-
es below in order to use the Bolt-Through assembly
method.
Size for one hole: Minimum 2.2’’ and maximum 3.1’’ in
diameter. Both bolts will t through holes within this
range.
Size for two holes: Minimum 0.4’’ and maximum of 1.3”
spaced 1.7” apart at centers. One bolt will t through
each hole.
Using a grommet hole that is already in your desktop
is acceptable, or you can drill holes at these measure-
ments anywhere on your desktop.
2.2”
3.1”
1.7’’
0.4”
1.3’’

© UPLIFT Desk • 800-349-3839 • [email protected] • upliftdesk.com 3
Optional Step 2.6 - Bolt-Through Base
Remove both bolts from the bottom of the Low-
er Clamp using the 6mm Allen Wrench. Slip them
through the two holes on either side of the Lower
Base Plate’s center hole as shown.
If assembling on an adjustable height desk, raise the
desk so the desktop hole is easier to see. Then insert
the bolts through the desktop hole from below, and
hold them in place.
Optional Step 2.7 - Bolt-Through Base
While holding the Lower Base Plate and bolts in place
from below, line up the holes of the Base assembly
(from Step 1) with the top of the bolts. Make sure the
front of the Base assembly is facing towards the front
of your desk. Hand tighten the bolts from below to
get the threads started in the Base assembly.
Once both bolts have been started, you can let go of
the Lower Base Plate. Hold the Base assembly in place
on top as you tighten the bolts, alternating from one
bolt to the other, allowing the Lower Base Plate to rise
evenly. Use the 6mm Allen Wrench to nish tighten-
ing the assembly to the desktop.
~270°
Arm & Monitor Assembly
Step 3
Slide the Lower Arms onto the posts of the Base un-
til it is fully seated and tighten each lower set screw
with the at-head end of the 3mm Allen Wrench (or a
small at head screwdriver). This will secure the Low-
er Arms to the Base and keep it from becoming sepa-
rated during adjustment.
With the lower set-screws tightened, each lower arm
rotates about 270° in total, depending on monitor size,
monitor orientation, and the location of the other arm.
Optional Step 2.5 - Bolt-Through Base
Align the Upper Base Plate with the Base in the orien-
tation shown and attach it using the four M6x12 Flat-
head Screws and the 4mm Allen Wrench.
Then peel the adhesive backing off of the Adhesive
Pad and attach it to the bottom of the Base and Up-
per Base Plate as shown. Align the pad with the front
edge of the Base rst, then work to the back.

© UPLIFT Desk • 800-349-3839 • [email protected] • upliftdesk.com
4
Step 4
Slide the Upper Arms into the holes on the Lower
Arms until they are fully seated and tighten the set
screw on the Lower Arms with the at-head end of
the provided 3mm Allen Wrench (or a small at head
screwdriver).
This will prevent the Upper Arms from becoming sep-
arated from the Lower Arms during adjustment.
Step 5
Note: Acceptable monitor weight range for the Crest-
view Dual Monitor Arm is 2.2 lb to 33 lb per arm.
Lay your monitor face down on a clean surface or a
towel to prevent damage to your screen. Test the M4x12
and M5x12 screws in your monitor’s screw holes to de-
termine which is the right size for your monitor.
Line up the holes of the VESA Plate with the holes on
your monitor. Make sure the word “TOP” is facing the
top of the monitor. Attach the VESA Plate to the moni-
tor using the selected screws with the M5 Washers.
Step 6
Pull the tab on the Upper Arm back and slide the
VESA Plate in (as shown in the illustration). Slide it in
until the tab on the Upper Arm clicks into place.
Repeat with the second monitor.
Pull up slightly on your monitors to make sure they are
locked securely in place.
Step 7 - Counterbalance
Move the monitor to any position and release it. If the
monitor does not drift up or down, the arm is properly
counterbalanced.
If the monitor does not remain where you positioned
it, you will need to adjust the tension of the gas spring
to properly support the weight of your monitor.
If the monitor drifted down, hold the Upper Arm in
a horizontal position and use the 6mm Allen Wrench
to turn the adjustment screw toward the “+” until the
monitor remains in place when you let go.
If the monitor drifted upward, turn the adjustment
screw towards the “-” symbol.
Repeat with the second arm.

© UPLIFT Desk • 800-349-3839 • [email protected] • upliftdesk.com 5
Step 8
To adjust the front and back tilt of your monitor, loos-
en the socket head screw on the side of the VESA
Mount with the 6mm Allen Wrench.
Once the monitor is at your preferred viewing angle,
re-tighten the screw with the Allen Wrench to hold
the monitor in place.
Repeat with the second monitor.
Step 9
To use the arm’s wire management, rst remove the
built-in wire covers.
The Upper Wire Cover is located on the Upper Arm
and is held in place by a screw and a clip. Remove the
screw with a Phillips head screwdriver, and slide the
cover slightly toward the monitor to disengage the
clip and remove the cover.
The Lower Wire Cover located on the Lower Arm and
is removed by hooking a nger through the bottom
opening in the cover, then holding it rm while pulling
it forward to unlock.
Run your cables up and under each section of the
monitor arm and replace the covers the same way
that they were removed.
Step 10
Snap the Wire Cover onto the back of the Base as
shown and insert your monitor cables through the
two clips. In addition to holding the cables in place,
there are convenient holes to store the Allen Wrench-
es for future adjustment needs.
Note: The Wire Cover adds 0.8” to the back of the
monitor arm. If your desk is close to a wall or cubi-
cle, or has a privacy panel attached to the back of the
desktop, there may not be enough space available to
attach the Wire Cover. If this is the case, simply do not
install the Wire Cover.

© UPLIFT Desk • 800-349-3839 • [email protected] • upliftdesk.com
6
Monitor Tilt
The Monitor can tilt at the VESA mount forward or
backward within a range of 90° (+/-45°).
Height Adjustment
The center of the VESA mount can go as high as 23”
and as low as 10’’ from the desktop.
10”
23”
Monitor Swivel
The Monitors can swivel 180° (+/-90°) at the hinge at
the top of the upper arm.
Monitor Rotation
The Monitors can rotate at the VESA mount 180°
(+/-90°) allowing landscape or portrait viewing.
Upper Arm Swivel
The Upper Arm can swivel a full 360°. However, we
do not recommend swiveling the monitor past the
back of the desk as this may cause instability.
Lower Arm Swivel
Each Lower Arm rotates about 270° in total, depend-
ing on monitor size, monitor orientation, and the loca-
tion of the other arm.
Adjustment Information
CAUTION: Read all instructions before assembly. Failure to assemble or operate properly may
result in damage or personal injury. Retain manual for future reference.
CAUTIONS & WARNINGS
!
!

© UPLIFT Desk • 800-349-3839 • [email protected] • www.upliftdesk.com
Notes

AI-MON010-2, MON032-1.0
512-614-3152
800-349-3839
[email protected]
upliftdesk.com
Work Better. Live Healthier
Copyright Notice: This guide is a component of this UPLIFT Desk product. This guide is a part of the scope of delivery, even if the item is resold. This
guide is also available on the UPLIFT Desk website: upliftdesk.com. Excerpts or copies may not be forwarded to third parties or used in any other
published form without the prior written consent of UPLIFT Desk. These instructions are subject to United States copyright law.
©
SAVE THESE INSTRUCTIONS
Study this manual carefully. If this desk is sold, please provide this
manual to the buyer, installers, or support personnel operating the product.
®