Uplift Desk Crestview MON033 User manual
Package Contents
Crestview Align Dual Monitor Arm
SKU: MON011-2, MON033
Allen Wrenches
(set of three: 3mm, 4mm, 6mm)
Handle
Bar
M5x12 Screw (M-B) (qty 8)
M5 Washer (M-C) (qty 8)
M4x12 Screw (M-A) (qty 8)
M6x12 Flathead Screw (qty 4)
M6x12 Panhead Screw (qty 4)
M6x22 Screw (qty 2)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
1
Package Contents
Part for
Bolt-through assembly
Lower Arm
Wire
Cover
Upper Arm
Lower
Clamp
VESA Plate
(qty 2)
Adhesive
Pad
Upper Base Plate
Upper
Clamp
Lower
Base Plate
Base
Note: ACCEPTABLE MONITOR WEIGHT RANGE IS 2.2 to 17.6 lb. (each monitor)
Step 1
If you purchased the Crestview Monitor Arm Wiring
Kit, assemble that FIRST, before proceeding. Refer to
the separate instructions contained in the Crestview
Monitor Arm Wiring Kit (ACC076) package for com-
plete details.
Base
Lower arm
Upper arm
Vesa mount (x1)
Lower base plate
Upper base plate
Bar Handle
Adhesive Pad
Wire Cover
Upper Clamp
Lower Clamp
Base screw (x4)
3mm Allen wrench
L
4mm Allen wrench
M
6mm Allen wrench
N
D5 Washers (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
O Bolt (x4)
N Bolt (x4)
Step 2
There are two ways to attach the Crestview Align Dual
Monitor Arm to your desktop.
If you would like to attach the monitor arm along the
back edge of your desktop, follow the Clamp Base
Assembly instructions (Step 2.1 - 2.3) and ensure your
desk is between 0.4” and 3.3” thick.
If you prefer to attach the monitor arm through your
desktop, follow the Bolt-Through Base Assembly in-
structions (Step 2.4 - 2.7) and ensure your desk is be-
tween 0.4” and 1.8” thick.
Step 2.1 - Clamp Base - only complete steps 2.1 to
2.3 if clamping the monitor arm to the edge of your
desktop. There is also a Bolt-Through option that
starts on step 2.4.
Align the Upper Clamp with the Base in the orienta-
tion shown. Attach using four M6x12 Flathead Screws
and the 4mm Allen Wrench.
Then peel the adhesive backing off of the Adhesive
Pad and attach it to the bottom of the Base and Upper
Clamp as shown. Align the pad with the front edge of
the Base rst, then work to the back.
Clamp Base Bolt-Through Base
Step 2.2 - Clamp Base
Use the 4mm Allen Wrench to adjust the four pre-in-
stalled screws on the back of the Lower Clamp so that
there are about 0.25” of thread between the plate and
screw heads.
There are two sets of key slot holes to choose from for
different desktop thicknesses.
For Desks 0.4’’ to 2.25’’ use the top four holes (g. 1)
For Desks 2’’ to 3.3’’ use the bottom four holes (g. 2)
Insert the four screws of the Lower Clamp through
four of the key slot holes in the back of the Upper
Clamp as shown.
Slide the Lower Clamp assembly down so that the
screws are at the bottom of the key slot holes then
tighten screws with 4mm Allen Wrench.
g. 2g. 1
6mm
6mm
6mm
6mm
Step 2.3 - Clamp Base
Using the 6mm Allen Wrench, adjust both bolts on
the bottom of the Lower Clamp so that the opening
is wide enough to accommodate the thickness of the
desktop and Lower Base Plate.
Place the outer holes of the Lower Base Plate onto the
tips of the bolts as shown.
Slide the assembly onto the back of the desktop, then
tighten the bolts using the 6mm Allen Wrench. Alter-
nate from one bolt to the other, to allow the Lower
Base Plate to rise evenly before nally tightening to
the desktop.
Optional “Bolt-Through Base” Assembly
Only complete steps 2.4 to 2.7 if you are not going to clamp the monitor arm to the desktop.
Optional Step 2.4 - Bolt-Through Base
Ensure the desktop has a hole between 0.4’’ and 3.1’’
in diameter to use this option. Using a grommet hole
that is already in your desktop is acceptable, or you
can drill a 0.5” hole anywhere on your desktop.
Optional Step 2.5 - Bolt-Through Base
Align the Upper Base Plate with the Base in the orien-
tation shown and attach it using the four M6x12 Flat-
head Screws and the 4mm Allen Wrench.
Then peel the adhesive backing off of the Adhesive
Pad and attach it to the bottom of the Base and Up-
per Base Plate as shown. Align the pad with the front
edge of the Base rst, then work to the back.
0.4”
3.1”
Optional Step 2.7 - Bolt-Through Base
While holding the Lower Base Plate and bolt in place
from below, line up the hole of the Base assembly
(from Step 1) with the top of the bolt. Make sure the
front of the Base assembly is facing towards the front
of your desk. Hand tighten the bolt from below to get
the threads started in the Base assembly.
Once the bolt is started, you can let go of the Lower
Base Plate. Hold the Base assembly in place on top as
you tighten the bolt. Use the 6mm Allen Wrench to
nish tightening the assembly to the desktop.
Step 3
Slide the Lower Arm onto the post of the Base until it
is fully seated and tighten the lower set screw with the
at-head end of the 3mm Allen Wrench (or a small at
head screwdriver). This will secure the Lower Arm to
the Base and keep it from becoming separated during
adjustment.
To limit the Lower Arm to only 180° of rotation, tight-
en the upper set screw also. This setting is helpful
when your desk is located against a wall or you are
installing a privacy panel to the back of the desk. Do
not over-tighten this set screw, doing so may hinder
arm movement.
To allow 360° of rotation, loosen the upper set screw
until the Lower Arm can rotate past the back of the
desk.
Optional Step 2.6 - Bolt-Through Base
Remove one of the bolts from the bottom of the Low-
er Clamp using the 6mm Allen Wrench. Slip it through
the Lower Base Plate’s center hole as shown.
If assembling on an adjustable height desk, raise the
desk so the desktop hole is easier to see. Then insert
the bolt through the desktop hole from below, and
hold them in place.
Arm & Monitor Assembly
180°
Step 4
Slide the Upper Arm into the hole on the Lower Arm
until it is fully seated and tighten the set screw on the
Lower Arm with the at-head end of the provided
3mm Allen Wrench (or a small at head screwdriver).
This will prevent the Upper Arm from becoming sepa-
rated from the Lower Arm during adjustment.
Step 7
The sockets slide freely along the bar; we advise slid-
ing the sockets to each end of the bar to allow more
room when attaching the monitors. Insert each mon-
itor’s VESA attachment into the sockets on the Bar.
The screw on the bottom of each socket provides up
to 5mm of height adjustment to help align the mon-
itors. Turn the screw either direction with a Phillips
head screw driver to set the height. (g. 1)
Next, tighten the screw on the side of each socket to
lock the monitors in place. (g. 2).
Pull up slightly on your monitors to make sure they are
locked securely in place.
Once the monitors are attached to the sockets, you
can slide them inward to position them as desired. We
recommend they meet in the center of the bar.
g. 2
g. 1
4
Top
Step 5
Line up the Bar with the mount at the end of the Up-
per Arm. Important: Make sure the bar is oriented cor-
rectly when installing. The open part of the sockets
should be facing up.
The pre-installed bolts on the Bar should be visible
through the large holes on the mount, and most im-
portantly, the four center holes on the Bar and on the
mount should line up.
Hold the Bar in place, and begin attaching the Bar to
the Upper Arm using the four M6x12 Panhead screws
in the holes shown. Thread each screw by hand until
all four screws are added, then tighten using the 4mm
Allen wrench.
Step 6
Note: Acceptable monitor weight range for the Crest-
view Single Monitor Arm is 2.2 lb to 17.6 lb.
Lay your monitor face down on a clean surface or a
towel to prevent damage to your screen. Test the M4x12
and M5x12 screws in your monitor’s screw holes to de-
termine which is the right size for your monitor.
Line up the holes of the VESA plate with the holes on
your monitor. Attach the VESA plate to the monitor
using the selected screws with the M5 Washers.
Note: Make sure the VESA plate is in the orientation
shown for proper attachment to the Bar.
Step 10
The angle of the Bar can be adjusted up to 4 degrees
in either direction.
To adjust the angle of the Bar, use the 4mm Allen
wrench to slightly loosen the four screws shown on
the back of the Bar attachment piece. Do not remove
these screws completely.
Once the four screws are loose, adjust the angle of the
Bar and monitors until they are positioned how you
like them and then re-tighten the four screws.
Step 8
There are four options for the attachment of the Han-
dle to the Bar. Choose between the two sets of holes
on the Handle and two sets of holes in the Bar to de-
termine which combination is best for you and allows
the bottom of the Handle to clear the bottom of your
monitors.
Note: When installing the Handle, you may need to
squeeze the ends together or pull them apart slightly
in order to align the holes in the Handle with the holes
in the Bar.
Connect the Handle to the Bar using the two M6x22
screws and the 4mm Allen wrench.
Step 9 - Counterbalance
Move the monitor assembly to any position and re-
lease it. If the monitor assembly does not drift up or
down, the arm is properly counterbalanced.
If the monitor assembly does not remain where you
positioned it, you will need to adjust the tension of
the gas spring to properly support the weight of your
monitor assembly.
If the monitor assembly drifted down, hold the Upper
Arm in a horizontal position and use the 6mm Allen
Wrench to turn the adjustment screw toward the “+”
until the monitor assembly remains in place when you
let go.
If the monitor assembly drifted upward, turn the ad-
justment screw towards the “-” symbol.
6
Step 12
Snap the Wire Cover onto the back of the Base as
shown and insert your monitor cables through the
two clips. In addition to holding the cables in place,
there are convenient holes to store the Allen Wrench-
es for future adjustment needs.
Note: The Wire Cover adds 0.8” to the back of the
monitor arm. If your desk is close to a wall or cubi-
cle, or has a privacy panel attached to the back of the
desktop, there may not be enough space available to
attach the Wire Cover. If this is the case, simply do not
install the Wire Cover.
Step 11
To use the arm’s wire management, rst remove the
built-in wire covers.
The Upper Wire Cover is located on the Upper Arm
and is held in place by a screw and a clip. Remove the
screw with a Phillips head screwdriver, and slide the
cover slightly toward the monitor to disengage the
clip and remove the cover.
The Lower Wire Cover located on the Lower Arm and
is removed by hooking a nger through the bottom
opening in the cover, then holding it rm while pulling
it forward to unlock.
Run your cables up and under each section of the
monitor arm and replace the covers the same way
that they were removed.
Monitor Assembly Swivel
The monitor assembly can swivel 180° (+/-90°) at the
hinge at the top of the Upper arm.
Monitor Assembly Rotation
The Bar and monitor assembly can rotate clockwise
4° or counterclockwise 4°.
See page 5, step 10 for more details.
Individual Monitor Rotation
Each monitor can rotate at each VESA mount a full
360°.
Adjustment Information
Height Adjustment
The center of the VESA mount can go as high as 23.4”
and as low as 10.4’’ from the desktop.
10.4”
23.4”
Monitor Tilt
Vertical
Each Monitor can tilt from it’s VESA mount forward or
backward in a range of 20° (+/-10°).
Horizontal
The Monitor can tilt horizontally at the VESA mount
right or left in a range of 20° (+/-10°).
AI-MON011-2, MON033-1.0
CAUTION: Read all instructions before assembly. Failure to assemble or operate properly may
result in damage or personal injury. Retain manual for future reference.
CAUTIONS & WARNINGS
!
!
Copyright Notice: These instructions are a component of this UPLIFT Desk product. These instructions are part of the scope of delivery, even if the item is resold. These instructions are also available on the UPLIFT Desk website:
upliftdesk.com. Excerpts or copies may not be forwarded to third parties or used in any other published form without the prior written consent of UPLIFT Desk. These instructions are subject to United States copyright law.
©
Lower Arm Swivel
The Lower Arm can swivel a full 360° or can be set to
allow only a range of 180° preventing it from rotating
past the back edge of the desktop.
Note: We do not recommend rotating the monitors
past the back edge of the desk as this may cause the
base to become unstable.
See Step 3 in the “Arm & Monitor Assembly” section
for adjustment details.
Upper Arm Swivel
The Upper Arm can swivel a full 360°. However, we
do not recommend swiveling the monitor past the
back of the desk as this may cause instability.
Other manuals for Crestview MON033
1
This manual suits for next models
1
Table of contents
Other Uplift Desk Rack & Stand manuals
Uplift Desk
Uplift Desk ACC301 User manual
Uplift Desk
Uplift Desk Zilker Dual Monitor Arm User manual
Uplift Desk
Uplift Desk Zilker Single Monitor Arm User manual
Uplift Desk
Uplift Desk MON056 User manual
Uplift Desk
Uplift Desk Crestview MON032 User manual
Uplift Desk
Uplift Desk Crestview MON031 User manual
Uplift Desk
Uplift Desk Crestview MON033 User manual
Uplift Desk
Uplift Desk MON051 User manual
Uplift Desk
Uplift Desk MON053 User manual
Uplift Desk
Uplift Desk ACC304 User manual
Uplift Desk
Uplift Desk ACC092 User manual
Uplift Desk
Uplift Desk Zilker MON002 User manual
Uplift Desk
Uplift Desk Motion-X 6-Pack Rack ACC052 User manual
Uplift Desk
Uplift Desk CPU128 User manual
Uplift Desk
Uplift Desk STR017-SHT User manual
Uplift Desk
Uplift Desk STR045 User manual
Uplift Desk
Uplift Desk ACC302 User manual
Uplift Desk
Uplift Desk ACC095 User manual
Uplift Desk
Uplift Desk MON054 User manual
Uplift Desk
Uplift Desk MON021 User manual
