urmet domus 1717/32 System manual

3DS1717-019
ENGLISH
The monitor Ref.1717/32 or /34 is an IP video door phone dedicated to the IPerVoice system.
For trouble-free operation, the device requires a LAN/POE-type connection.
DESCRIPTION OF COMPONENTS AND CHARACTERISTICS
7 8
1
6
5 4
3
11 9
2
10
7” touchscreen display
Webcam 2Mpx
Microphone
Backlit blue Home button
Speakers
Micro SD card
Switch for IPerHOME bus termination
(IPERHOME TERM)
1.
2.
3.
4.
5.
6.
7.
12 way connector for external connections’
printed circuit
Secondary LAN connector for Internet
IPerHOME connection (LOCAL LAN PORT)
IPerVoice LAN connector with POE power
supply (DOORPHONE POE PORT)
Micro USB connector for Eeprom programming
(for future developments)
8.
9.
10.
11.
DESCRIPTION OF TERMINAL PINS
1
2
4
PANIC
FC
S+
S-
+B
-B+V-V
+ -
3
1. 12 way connector used for monitor connection to the printed circuit
2. Terminals for the connection of:
• panic alarm (PANIC)
• oor call (FC)
• call repeater (S+, S-)
3. Terminals for connection to the IPerHOME system (-V, +V, -B, +B)
4. External power supply terminals (24 V : +, -)
WIRING INSTRUCTIONS
RJ45 Ethernet Cable
The IPerVoice system has been designed to work with the EIA/TIA 568B standard.
Plug the cable into one of the RJ45 connectors with the Urmet logo.
Insert the wire in its guide, according to the provided colour code (Standard T568B).
•
•

4
DS1717-019
Black sheath
8
1
Wire
No. Cable colour
1 White-Orange
2 Orange
3 White-Green
4 Blue
Wire
No. Cable colour
5 White-Blue
6 Green
7 White-Brown
8 Brown
Grey sheath
Cut the cables so that they protrude from the guide by about 5 mm, insert the guide in its plug and crimp
with the specially provided tool.
Plug
8
1
~ 5 mm
8
1
Make sure that the grey sheath stays inside the plug.
This type of connection will NOT guarantee double insulation.
POWeR SuPPLY
The 1717/32 or /34 monitor can be supplied power in two different ways:
POE
24 V – 18 W power supply
When the power supply is used, POE is not available because the monitor is powered only by the local
power supply. In this case, RJ45 can be connected to the NO POE port of the switch.
INSTaLLaTION
It is possible to x the wall bracket by using a 503 box and the supplied screws, or a Ø 60 box with suitable
screws.
1,50 m
Box
503
1,50 m
Box
Ø 60 mm
Connect any panic function, extra ring tone, oor call, auxiliary power and link to IPerHOME system
function wires to the terminals on the external printed circuit.
Connect the monitor to the connector CN1 on the printed circuit board via the cable provided on the
back of the monitor.
Move the monitor close to the bracket by centring the special xings 1and slide it down to reach its
stop
2
(see the following image).
•
—
—
•
•
•

5
DS1717-019
1
2
DISTANCES, SECTIONS, CABLES AND TECH SPECS
Type of connection Max distance Min - max cross section
Call to oor level 30 m 0,5 - 1 mm2
Panic Alarm 30 m 0,5 - 1 mm2
Call repeating 30 m 0,5 - 1 mm2
External 24 Vdc 25 m 0,5 - 1 mm2
LAN 100 m CAT5e (*)
(*) To ensure longest-range monitor operation, the cable must be a class 5e device and the twisted pairs’
cross section must be AWG24.
The maximum resistance of the individual wires must not exceed 10ohm/100m.
The cable must be up to the following standards:
- EIA/TIA 568-B.2 or EIA/TIA 568-C.2
- EN50288 3-1
- IEC 61156-5
The connection between the monitor and POE switch must be ensured by a single cable without any
extra patch cords.
POE input voltage: ..........................................................................................................................48-54 V
External power supply voltage: ............................................................................................................ 24 V
Max consumption:....................................................................................................................................12 W
Display:.................................................................................................................................................. 7” TFT
Touchscreen:.................................................................................................................................. Capacitive
Resolution: ................................................................................................................................ 1024 x 600 px
Brightness: ...................................................................................................................................... 350 cd/m2
Viewing Angle (H/V):....................................................................................................................... 160° / 160°
Operating Temperature: .................................................................................................................. -5 to 45°C
IPerHOME CU Consumption:................................................................................................................0.5 CU
Max number of monitors on the POE ports of switch 1039/44:..................................................................... 2
This product is intended to be powered by either any external power supply units, through
the connector M1 on the board CS1717-014 (18W, 24Vdc) or PoE, through the connector
CN505 whose power supply conforms to the limited power source (LPS) requirements and
is protected against short circuits and power surges in accordance with the EN 60950-
1:2006+A11+A1+A12+A2 requirements.
If a local power supply is used, do not connect the LAN input to the switch POE outputs.

DS1717-019 6
This device complies with Part 15 of the FCC rules subject to the following two conditions:
1) This device may not cause harmful interference
2) This device must accept all interference received, including intereference that may cause
undesired operation.
15.105 Information to the user statements:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
RF exposure warning statement
To comply with FCC RF exposure compliance requirements, a separation distance of at least 20 cm must
be maintained between the antenna of this device and all nearby persons
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.

7 DS1717-019

DS 1717-019
LBT 20142
Area tecnica
servizio clienti +39 011.23.39.810
http://www.urmet.com
e-mail: [email protected]
Prodotto in P.R.C. su specica Urmet.
Manufactured in P.R.C. on Urmet specication.
URMET S.p.A.
10154 TORINO (ITALY)
VIA BOLOGNA 188/C
Telef. +39 011.24.00.000 (RIC. AUT.)
Fax [phone] - 323
This device complies with Part 15 of the FCC rules subject to the following two conditions:
1) This device may not cause harmful interference
2) This device must accept all interference received, including intereference that may cause
undesired operation.