Ursalink UG85 User manual

LoRaWAN Agricultural Kit Quick Guide
2
Safety Precautions
Ursalink will not shoulder responsibility for any loss or damage resulting from not following
the instructions of this operating guide.
The kit must not be remodeled in any way.
UC11-T1 and EM500 are not intended to be used as reference sensors, and Ursalink will
not should responsibility for any damage which may result from inaccurate readings.
Do not place the all devices close to objects with naked flames.
Do not place all devices where the temperature is below/above the operating range.
Make sure electronic components do not drop out of the enclosure while opening.
When closing the lid, make sure the lid is fitted the right way, so that the enclosure is
properly sealed.
When installing the battery of sensors, please install it accurately, not reversely or with
wrong model.
The kit must never be subjected to shocks or impacts.
Declaration of Conformity
Ursalink LoRaWAN agricultural kit is in conformity with the essential requirements and other
relevant provisions of the CE, FCC, and RoHS.
© 2017-2020 Xiamen Ursalink Technology Co., Ltd.
All rights reserved.
All information in this guide is protected by copyright law. Whereby, no organization or individual
shall copy or reproduce the whole or part of this user guide by any means without written
authorization from Xiamen Ursalink Technology Co., Ltd.
For assistance, please contact
Ursalink technical support:
Email: [e-mail]
Tel: [phone]
Fax: [phone]
Revision History
Date
Doc Version
Description
July 27, 2020
V 1.0
Initial version

LoRaWAN Agricultural Kit Quick Guide
3
Contents
1. Overview..........................................................................................................................................4
1.1 Description............................................................................................................................ 4
1.2 Topology................................................................................................................................ 4
2. Introduction.....................................................................................................................................4
2.1 Packing List............................................................................................................................ 4
2.2 Software Preparation............................................................................................................ 5
3. UG85 Gateway Configuration..........................................................................................................6
3.1 SIM Card/Antenna Installation.............................................................................................. 6
3.2 Web GUI Configuration......................................................................................................... 6
3.2.1 Login the Web GUI..................................................................................................... 6
3.2.2 Network Connection.................................................................................................. 8
3.2.3 Network Server Configuration................................................................................. 10
4. UC11-T1 Configuration..................................................................................................................11
4.1 Turn ON/OFF UC11-T1.........................................................................................................11
4.2 USB Configuration............................................................................................................... 11
5. UC1114 Configuration................................................................................................................... 12
5.1 Antenna Installation............................................................................................................ 12
5.2 UC1114 Configuration......................................................................................................... 12
6. EM500 Configuration.................................................................................................................... 13
6.1 Turn on/off the Sensor........................................................................................................ 13
6.2 EM500 Configuration.......................................................................................................... 14
6.2.1 Mobile APP Configuration........................................................................................14
6.2.2 Windows Software Configuration............................................................................15
7. Ursalink Cloud Configuration........................................................................................................ 16
7.1 Ursalink Cloud Registration................................................................................................. 16
7.2 Add a UG85 to Cloud...........................................................................................................17
7.3 Add Ursalink LoRaWAN Nodes to Cloud............................................................................. 17
8. Hardware Installation.................................................................................................................... 19
8.1 UG85 Installation.................................................................................................................19
8.2 UC11-T1 Installation............................................................................................................19
8.3 UC1114 Installation............................................................................................................. 19
8.4 EM500 Installation.............................................................................................................. 20
8.4.1 Sensor Installation....................................................................................................20
8.4.2 Transceiver Installation............................................................................................ 21
Appendix............................................................................................................................................22
Default Uplink Channels............................................................................................................22
Default LoRaWAN Parameters.................................................................................................. 23

LoRaWAN Agricultural Kit Quick Guide
4
1. Overview
1.1 Description
Ursalink LoRaWAN Agricultural Monitoring Node-to-App Starter Kit is designed for simplifying the
process of PoC about LoRaWAN network establishment and remote monitoring for the
agricultural environment. More information about every product is available on
https://www.ursalink.com/en/documents-download/
1.2 Topology
2. Introduction
2.1 Packing List
1 × UG85
1 × Ethernet Cable
1 × Power Adapter
1 × Stubby LoRa Antenna
1 × DIN Rail Kit
4 × Setscrews
(For UG85)
1 × Magnetic
Cellular Antenna
1 × 6-Pin Pluggable
Terminal

LoRaWAN Agricultural Kit Quick Guide
5
1 × UC11-T1
1 × Magnet
Setscrews
(For UC11-T1)
1 × UC1114
1 × Stubby LoRa
Antenna
1 × 12-Pin Pluggable
Terminal
Setscrews
(For UC1114)
1 ×
EM500-SMT-MEC20
1 ×
EM500-LGT
Mounting Screws
(For EM500)
Hose Clamps
Please contact your Ursalink sales representative if the following situations occurs:
Any of above items is missing or damaged;
Other accessories or device models are required for your application.
2.2 Software Preparation
Software
Introduction
Apply For
Download
Ursalink Toolbox
Windows software for NFC/USB
configuration.
UC11-T1,
UC1114, EM500
sensors
https://www.ursalink.
com/en/software-do
wnload/
Ursalink Toolbox
(APP ver.)
Mobile APP for NFC
configuration.
EM500 sensors
Apple Store or
Google Play
Ursalink Cloud
(APP ver.)
Add and manage the LoRaWAN
nodes on the Ursalink Cloud.
Ursalink Cloud
Apple Store or
Google Play

LoRaWAN Agricultural Kit Quick Guide
6
3. UG85 Gateway Configuration
3.1 SIM Card/Antenna Installation
A. Unscrew the cover of the SIM card then take it off.
B. Put SIM card into the slot and screw it up.
C. Rotate the antenna into the antenna connector accordingly.
The external antenna should be installed vertically always on a site with a good signal.
3.2 Web GUI Configuration
Default settings of UG85:
IP Address: 192.168.23.150
Username: admin
Password: password
3.2.1 Login the Web GUI
A. Connect PC to LAN port of UG85 directly.
B. Go to “Control Panel”→“Network and Internet”→”Network and Sharing Center” of the
PC and click “Ethernet”.

LoRaWAN Agricultural Kit Quick Guide
7
C. Click “Properties”→“Internet Protocol Version 4(TCP/IPv4)” to configure a static IP address
manually and save the configuration.
D. Open a web browser on your PC (Chrome and IE are recommended) and type in the IP
address 192.168.23.150.
E. Enter the username and password to “Login” the web GUI of UG85.

LoRaWAN Agricultural Kit Quick Guide
8
3.2.2 Network Connection
UG85 supports Ethernet, cellular(3G/4G) and Wi-Fi(option) backhaul. This guide will introduce
how to make gateway access the network via Ethernet and cellular network.
3.2.2.1 Configure the WAN Connection
A. Go to “Network”→ “Interface” → “Port” page to select the connection type and configure
WAN information.
B. Click “Save&Apply” for configuration to take effect.
C. Connect Ethernet port of gateway to network devices like router or modem.
D. Log in the web GUI via the newly assigned IP address and go to “Status”→ “Network” to
check Ethernet port status.
3.2.2.2 Configure the Cellular Connection
Take inserting SIM card into SIM1 slot as an example; please refer to the following detailed
operations.
A. Go to “Network” → “Interface” → “Cellular” → “Cellular Setting” page to enable SIM1.

LoRaWAN Agricultural Kit Quick Guide
9
B. Choose relevant network type and type SIM card information like APN and PIN code.
C. Click “Save” and “Apply” for configuration to take effect.
UG85 has two cellular interfaces named SIM1 & SIM2. Only one cellular interface is active at
one time. If both cellular interfaces are enabled, SIM1 interface takes precedence by default.
D. Go to “Status” → “Cellular” page to view the status of the cellular connection. If it shows
“Connected”, it means SIM1 has dialed up successfully. On the other hand, you can check the
status of LTE indicator. If it keeps on green light statically, it means SIM has dialed up
successfully.

LoRaWAN Agricultural Kit Quick Guide
10
3.2.3 Network Server Configuration
A. Go to “Packet Forwarder” → “General” page to enable the “Ursalink” type server.
B. Go to “Network Server” → “General” page to enable the network server and Ursalink
Cloud mode.