US Robotics ADSL 4-Port Router User manual

1
ADSL 4-Port Router
Quick Installation Guide
Guide d'installation rapide
Installationsanleitung
Guida all'installazione rapida
Guía breve de instalación
Beknopte installatiegids
Kurulum Kýlavuzu
Οδηγός γρήγορης εγκατάστασης
Pokyny k instalaci naleznete v uživatelské prírucce na instalacním disku CD-ROM.
A telepítési utasításokat lásd a telepíto CD-ROM Felhasználói kézikönyvében.
Instrukcja instalacji jest dostepna w podreczniku uzytkownika na dysku instalacyjnym
CD-ROM.
Para obter instruções de instalação, consulte o Manual do Utilizador no CD-ROM de Instalação.
Инструкции по установке см. вруководстве пользователя на установочном компакт-
диске.
Installationsanvisningar finns i användarhandboken på installationsskivan.
R24.0706.00
rev 1.5 03/07

ADSL 4-Port Router Installation ................................................3
Installation du routeur ADSL 4-Port Router ..............................17
Installation des ADSL 4-Port Routers .......................................31
Installazione di ADSL 4-Port Router ..........................................45
Instalación del ADSL 4-Port Router ...........................................59
Installatie ADSL 4-Port Router ..................................................73
ADSL 4-Port Router Kurulumu .............................................87
Εγκατάσταση ADSL 4-Port Router .......................................101
Cesky
Pokyny k instalaci naleznete v uživatelské prírucce na instalacním disku CD-ROM.
Magyarország
A telepítési utasításokat lásd a telepíto CD-ROM Felhasználói kézikönyvében.
Polska
Instrukcja instalacji jest dostepna w podreczniku uzytkownika na dysku instalacyjnym CD-ROM.
Português
Para obter instruções de instalação, consulte o Manual do Utilizador no CD-ROM de Instalação.
Русский
Инструкции по установке см. вруководстве пользователя на установочном компакт-
диске.
Svenska
Installationsanvisningar finns i användarhandboken på installationsskivan.

3
ADSL 4-Port Router Installation
Thank you for purchasing the USRobotics ADSL 4-Port Router.
For current product support and contact information, go to the following Web site:
http://www.usr.com/support
NOTE: It is important that you have your serial number written down for future
reference. If you ever need to call our technical support department, you will
need this number to receive assistance. You can find your serial number on a bar
code sticker located on the bottom of the router and also on the box. You will also
need your model number. It is noted below.
Write your serial number in the space provided below.
What You Need Before You Begin
You will need active ADSL and Internet service from your local telephone company or
Internet Service Provider (ISP) before you can go on the Internet. You may also need the
following from your ISP:
• VPI/VCI values
• ADSL standard (modulation)
• Encapsulation mode
• Authentication (PAP or CHAP) for PPP connections
• Your user name and password, if they were assigned by your ISP.
Router Installation
Step 1. Connect Microfilter (if included or required by your ISP)
A microfilter removes interference between voice and DSL signals. Your ISP will determine
if a microfilter is necessary. If a microfilter was not included with the router, you may want
to ask your ISP if you need to purchase one or more.
To install a microfilter, plug a device (phone, fax machine, or other telephony device) into
the microfilter, and then plug the microfilter into the telephone wall jack. Do not install a
9107
Serial Number Model Number

4
microfilter on the cable that connects your ADSL router to the telephone jack unless your
microfilter has a connection for both the router and the phone.
Step 2. Connect the Cables
Use the supplied Ethernet cable to connect the router to the computer. This diagram
shows you how the devices will be connected when the installation is complete:
To make the needed connections, follow these steps:
A. Connect one end of the grey telephone cable to the telephone port on the back of
your router (labeled ADSL). Connect the other end to the telephone wall jack.
B. Connect the Ethernet cable. Although you can connect up to four systems this way,
you should start with one and connect additional devices only after the initial setup
is complete. Insert one end of the Ethernet cable into one of the ports on the back of
the router (labeled 1, 2, 3, and 4). Connect the other end to the Ethernet port on your
computer’s network interface card.
C. Plug the AC power adapter into the 9VDC jack on the back of your router. Then plug
the AC power adapter into a standard wall outlet. If the LED on the front panel is
not lighted, press the Power switch on the back of the router.
NOTEThis product is intended to be supplied by a UL Listed Direct Plug-in
Power Unit marked Class 2 and rated 9V DC, 1200 mA.

5
The router starts up after you turn on the power. This may take one to two minutes.
D. See if the and any of the indicator LEDs are lighted. If they are not, see the
troubleshooting section later in this guide.
Step 3. Install EasyConfigurator
1. Insert the USRobotics installation CD-ROM into your computer’s CD-ROM drive. The
installation should start automatically. This process may take a few moments.
If the installation does not start automatically, you can start it manually as follows.
Windows Vista users: Click Windows Start >Computer. Double-click the CD drive.
Windows users: Click Start and then Run, then type D:\setup.exe in the dialogue box
and click OK. (If your CD-ROM drive uses a different letter, type that letter in place of
D.)
Macintosh users: Open the CD-ROM and double click on either MacOS X Install or
MacOS Classic Install (depending on which operating system your computer uses).
Linux users: Open the CD-ROM, browse to \platforms\linux, and double-click on
install.bin.
2. Select your preferred language and click OK.
3. If you are using Windows, the installer runs a qualification test to verify that your
system meets the minimum requirements for installation. When qualification is
complete, a Results screen displays green flags next to system components that
meet requirements and red flags next to any that do not. If your system passes the
qualification, click Next. If any of your system components does not meet the
requirements, click View Report to identify them.
Setup now installs EasyConfigurator.

6
Step 4. Configure the Router with EasyConfigurator
1. This is the EasyConfigurator login window:
If EasyConfigurator does not start up automatically, you can open it yourself with
the following steps.
Windows Vista users: Click Start and select All Programs and U.S. Robotics
EasyConfigurator.
Windows users: Click Start and select Programs and U.S. Robotics
EasyConfigurator.
Macintosh and Linux users: Double-click on the EasyConfigurator icon on the
desktop.
In the EasyConfigurator login window, the user name and password are already
entered for you. Click Log In and wait a moment.

7
2. This window appears after you log in:
Select your country and your Internet Service Provider (ISP) from the drop-down
lists. If your country or ISP does not appear in the list, select Other and manually
enter the settings provided by your ISP.
You may need to enter your ISP-supplied user name and password after making your
selections. Click Apply to continue.
3. EasyConfigurator now configures your router based on your ISP selection or
manually-entered settings.

8
At this point, the system attempts to access the Internet. This may take a few
minutes, until the following status page appears.
If the status is CONNECTED TO THE INTERNET, you have successfully configured
your Internet connection. If it does not say CONNECTED TO THE INTERNET, go to the
Troubleshooting section of this installation guide.
You should now be able to access the Internet. We suggest that you register your product
and test your connection by going to the following Web site:
www.usr.com/productreg
See the User Guide on the USRobotics installation CD-ROM to learn about the router’s
advanced features, which are accessible from its Web User Interface.

9
Status LEDs
The router has several LEDs on its front. The LED conditions listed below indicate the
operational status of the router.
Solid The router is powered on.
Off The router is powered off.
Solid The router is connected to the Internet.
Flashing The router is exchanging data with the Internet.
Off
There is no active Internet connection or the device is
in ADSL bridge mode. For information on bridge mode,
see the User Guide on the installation CD-ROM.
Solid An ADSL link is established.
Flashing The router is attempting to create an ADSL link.
Off There is no current ADSL connection.
(1-4)
Solid
There is a physical connection between the router and
the computer through the corresponding Ethernet port
(note the port numbers above the LEDs).
Flashing The router and computer are exchanging data through
an Ethernet port.
Off There is no physical connection between the router
and the computer through the Ethernet port.
Solid
A printer is connected to the router’s USB port. See
the User Guide on the USRobotics installation CD-ROM
for information on using a printer with the router.
NOTE: Do not connect any device other than a self-
powered printer to the USB port. The USB connector
can only be loaded a maximum of 0.11A. Overloaded
operation is hazardous.
Flashing The router and printer are exchanging data.
Off There is no printer connected to the router’s USB port.

10
Router Back
NOTE: To reset the router, insert a pin or paper clip to briefly push the Reset
button. If you want to reset the router, do not press this button for more than 5
seconds, as this resets the router’s configuration to the factory defaults.
ADSL Digital subscriber line RJ-11 service jack
USB Port that accepts a USB cable to a printer.
1 - 4 Ethernet ports 1 - 4
Reset A recessed button that resets the router (see note below)
9VDC Input jack that accepts a cable from supplied power adapter
Power Rocker switch that turns the router on and off

11
Troubleshooting
To help diagnose a problem, first use the following troubleshooting checklist.
1. Confirm that you are using the AC power adapter that came with your router and
that it is connected to the router and to an active wall outlet. Make sure the
Power switch is switched to the on position. The LED should be lighted.
2. Confirm that you have securely connected the telephone cable to the telephone
wall jack and to the router. The LED should be lighted if you have correctly
configured DSL.
3. Confirm that you have secured the Ethernet cable(s) to the computer’s network
interface card and to the Ethernet port(s) on the router (labelled 1, 2, 3, or 4).
The corresponding LED should be lighted on the front of the router.
For more information on the LEDs, see the Status LEDs section earler in this document.
Opening the Web User Interface
The Web User Interface will be your main tool for configuring, troubleshooting and
monitoring the router. Follow this procedure to access it.
1. Start a Web browser.
2. Open the page http://192.168.1.1
3. A login window will appear:
Enter a user name and password and click OK. The default user name and password
are both admin.

12
4. The Web User Interface opens with a status page.
If you cannot access the Internet...
A number of devices have to work together for your computer to access the Internet. The
following drawing shows the connections between your computer and your USRobotics
ADSL 4-Port Router.
A. Your computer connects to your ADSL 4-Port Router via a wired connection (a cable).
B. The router connects to your Internet Service Provider (ISP) via ADSL over the phone
network.
The first step in solving the problem is to diagnose the cause. There are a number of
places where the connection from your computer to the Internet might fail.

13
Step 1: Can your computer connect to your ADSL 4-Port Router?
Open a Web browser to the router’s address: http://192.168.1.1 (Please note that if you’ve
modified the router’s LAN IP address, you must use the new one.) If the router’s Web User
Interface appears, go to Step 3. Otherwise, the router may need to be restarted:
1. Turn the router’s power off with the switch on the back. Wait a few seconds and turn
it back on again.
2. Wait one or two minutes as the router restarts.
Then ensure that one end of the Ethernet cable is connected to your computer’s LAN port
and the other end is connected to one of the Ethernet ports on the router. Also check that
the corresponding LED is lighted.
In the unlikely event that your computer is using a static IP address, either re-configure
your computer to use a dynamic IP address or ensure that its static IP address is in the
same network as the ADSL Router. (That means that the IP address has the format
192.168.1.x where xcan be any number between 2 and 254, inclusive.)
Now, please restart your computer. It will attempt to connect to the router. Continue on to
Step 2.
Step 2: Is your ADSL 4-Port Router responding?
Open your Web browser to the router’s address: http://192.168.1.1. If the router’s Web
User Interface appears, please go to Step 3.
If the router’s Web User Interface doesn’t appear, the router may need to be restored to
the default factory settings. (Please note that you will lose all of your router’s custom
settings and will need to set it up again as if you were installing it for the first time. If you’ve
made a backup of the settings, you will be able to restore them. Please see the User Guide
on the USRobotics installation CD-ROM for more information.)
Windows users: You can check your connections automatically with the
included utility program.
1. Use Windows Explorer to navigate to the Troubleshooting folder on your
USRobotics installation CD-ROM (for example, D:\Troubleshooting, if your CD-
ROM drive is labeled D:).
2. Double-click on Troubleshoot_Connection.
This utility program tests your connections and, if there is a problem, tells you
where it is.

14
1. With a thin tool such as a paper clip, press the Reset button on the back of the
router for at least five seconds.
2. Wait about one or two minutes as the router restarts.
3. Please restart your computer so that it will connect to the router.
4. Try to access the router’s Web address at http://192.168.1.1
If the router’s Web User Unterface still does not appear, the router may have failed. Please
contact USRobotics Customer Support. See the contact information later in this
document.
If the router’s Web User Interface appears, continue on to Step 3.
Step 3: Can your ADSL 4-Port Router connect to the Internet?
If you have a connection between your computer and your router, it’s likely that the router
is not connected to the Internet.
1. Close your Web browser and run EasyConfigurator.
Windows Vista users:
Press Start, then select All Programs and U.S. Robotics EasyConfigurator.
Windows users:
Press Start, then select Programs and U.S. Robotics EasyConfigurator.
Macintosh and Linux users:
Double-click the EasyConfigurator icon on the desktop.
2. Click Status at the top of the page, and check the value of the Status field.
Sample image of a router connected to the Internet:
Sample image of a router not connected to the Internet:
If the status is CONNECTED or CONNECTED TO THE INTERNET but you still cannot
access the Internet, please contact your ISP for assistance.
Otherwise, you need to configure your ADSL connection. Please click Configuration
at the top of the EasyConfigurator window and refer to the instructions earlier in this
document (see Step 4. Configure the Router with EasyConfigurator) for how to
configure your ADSL connection.

15
Additional Information
For regulatory and warranty information, see the User Guide on the USRobotics
Installation CD-ROM.
For operation and configuration information, see the
User Guide on the USRobotics
Installation CD-ROM. The User Guide contains detailed information on the use and
configuration of your ADSL 4-Port Router.
For expanded troubleshooting and additional information:
1. See the
User Guide on the USRobotics Installation CD-ROM.
2. Go to the Support section of the USRobotics Web site at
www.usr.com/support/.
Many of the most common difficulties that customers experience have been
addressed in the FAQ and Troubleshooting Web pages for your ADSL 4-Port
Router. The Support pages also contain information on the latest firmware and
may contain documentation updates.
3. Submit your technical support question using an online form, or contact
USRobotics customer support.
4. See the Support contact information on the last page of this guide.

16

17
Installation du routeur ADSL 4-Port Router
Nous vous remercions d'avoir choisi le routeur USRobotics ADSL 4-Port Router.
Pour obtenir de l'aide sur ce produit ou nous contacter, visitez le site Web suivant :
http://www.usr.com/support
REMARQUE : nous vous recommandons vivement de noter votre numéro de série
afin de pouvoir vous y référer par la suite. Vous en aurez besoin si vous devez
appeler notre service d'assistance technique. Vous trouverez ce numéro de série
sur l'étiquette de code-barre figurant sous le routeur et sur la boîte. Vous aurez
également besoin de votre numéro de modèle, indiqué ci-dessous.
Inscrivez votre numéro de série dans l'espace ci-dessous.
Ce qu'il vous faut avant de commencer
Avant de pouvoir vous connecter à Internet, vous aurez besoin des services ADSL et
Internet actifs proposés par votre opérateur téléphonique local ou votre fournisseur
d'accès Internet (FAI). Vous devez également obtenir les informations suivantes auprès de
votre FAI :
• Valeurs VPI/VCI
•NormeADSL(modulation)
• Mode d'encapsulation
• Authentification (PAP ou CHAP) pour connexions PPP
• Votre nom d'utilisateur et votre mot de passe, si votre FAI vous en a attribués
Installation du routeur
Etape 1. Connexion du microfiltre (si votre FAI l'exige ou s'il est fourni)
Un microfiltre empêche les interférences entre le téléphone et les signaux DSL. Votre FAI
déterminera si un microfiltre est nécessaire. Si aucun microfiltre n'est fourni avec le
routeur, demandez à votre FAI si vous devez en acheter un ou plusieurs.
Pour installer le microfiltre, branchez chaque appareil (téléphone, fax ou autres) au
microfiltre, puis raccordez ce dernier à la prise téléphonique murale. N'installez pas de
9107
Numéro de série Numéro de modèle

18
microfiltre sur le câble reliant votre routeur ADSL à la prise téléphonique, à moins que le
microfiltre ne dispose d'une prise pour le routeur et pour le téléphone.
Etape 2. Branchement des câbles
Reliez le routeur à l'ordinateur à l'aide du câble Ethernet fourni. Le schéma ci-dessous
vous montre toutes les connexions entre les périphériques une fois l'installation
terminée.
Pour effectuer les connexions requises, procédez comme suit :
A. Branchez une extrémité du cordon téléphonique gris au port téléphonique ADSL
situé à l'arrière de votre routeur. Branchez l'autre extrémité à la prise téléphonique
murale.
B. Connectez le câble Ethernet. Même s'il est possible de connecter jusqu'à quatre
systèmes de cette manière, nous vous conseillons de ne connecter les
périphériques supplémentaires qu'une fois l'installation initiale terminée. Branchez
une extrémité du câble Ethernet à l'un des ports (1, 2, 3 ou 4) situés à l'arrière du
routeur. Branchez l'autre extrémité au port Ethernet de la carte d'interface réseau
de votre ordinateur.
C. Branchez une extrémité de l'adaptateur secteur AC dans la prise 9VDC à l'arrière de
votre routeur et l'autre extrémité à une prise murale standard. Si le voyant DEL
situé à l'avant du routeur est éteint, appuyez sur l'interrupteur Power (Alimentation)
à l'arrière du routeur.