USUNG Smart IR Controller User manual

SmartIRController‐Manual

Productname:SmartIRController
Productdescription:thisisoneofthecomponentsofUSUNGSmartHomeSystem,andit
mustworkwithotherSmartHomecomponents.Itcanreplacevariousremotecontrollersto
controldifferentinfrareddevicessuchasairconditioners,TVs,DVDs,etc.

Installation&Usage:
1.Puttheinfraredcontrollerinupsidedownposition,andturnitsbottomcover
counterclockwiselyandopenit;
2.TakeouttheVIItwoAAAalkalinebatteriesfromthepackage,andinsertthebatteries
properlybyfollowingthepositive/negativeterminalmarks.
3.AligningthenotchonthebottomcovertotheprotrusionontopcoveroftheController,
dropthecoverandturnitclockwisely;
4.Placedirectly,orusethefoamtapecomeupwiththeproductpackagetofix,the
InfraredControllertoaproperposition;


Illustration:

Precautions:
1.Pleasechargethebatterieswiththechargercomeupwiththeproduct,andpleaseDO
NOTtrytochargeanon‐chargeablebattery,asmayleadtobatteryleakage,product
damageorpersonalinjury;
2.Pleasechargeusingthepoweradaptercomeupwiththeproduct;
3.Pleasedonotdisassembleortrytorepairtheproductinyourownwill;
4.Pleasedonotputtheproductunderextremeconditionslikehightemperatureorhigh
pressure,etc.;
5.Pleasekeeptheproductawayfrombabyorchild;
6.Pleasekeeptheproductdryandawayfromhumidity;
7.TheproductIDcanbeseenattheinnersideofthebottomcover.Youmayfinditwhen
openthebottomcoverbyturningitcounterclockwiselyandyou

XiamenTongrenIOTTechnologyCo.,Ltd.
24Hrhotlineservice:4008888022
Website：http://home.iusung.com

Smart Home Initial Configuration
and User Manual
SoftwareLoginConfiguration
zFirstly, please follow the user manual, correctly install the Smart Gateway
and other smart components, and power them on. Please make backup
and memo for each device during the installation in accordance with the
description of the attached ID Backup Table.
zSecondly, download and install the SmartHome Suite Client Software from
USUNG SmartHome System Official Website(downloading url:
http://home.iusung.com/download), or you may use a barcode scanner
tool from your mobile to check out the downloading address from the 2D
barcode shown below.
Note: There are various 2D barcode scanner tools available for mobiles, such as

Wechat. Take Wechat for example: select Discover -> choose Scan (if not available,
please enable the Scan tool in the Settings)
zThen, on your mobile, enter Settings Æ Wireless LAN, find the AP named
like“WIMA******”

zOpen the client software, from the Login interface , click on the “Initial

Usage Wizard”and enter the Router Configuration interface;


zIn Router Configuration interface, click on Confirmation button, and you
will be redirect to your mobile phone’s default browser, where you can
login to the Smart Gateway (with“admin”as both default username and
password );



zOnce logged in successfully, by following the interface requests, enter the
SSID of your Home WIFI, and please write down the MAC address shown in
the page that followed, which will be used in remote Controlling Settings


Or by auto-scanning using Scanning Hotspot function, you may choose the
SSID of your Home WIFI.


zInput the password for your home WIFI;

Click Save button to save the settings data.
Click Return to go back to the Router Configuration interface.
and then click on Return complete the settings.
zAfter completion of the above configuration, the Smart Gateway should
have joined your home WIFI.
Now, if your mobile has not yet connected to your home WIFI
automatically, please open the Settings Æ Wireless LAN, and connect your
mobile again to your home WIFI.


zReopen your mobile client software and go back to the login interface;
The client software will automatically search the Smart Gateway that joined
already in your home WIFI, and display it (or them) in the login list.
(This process will last for 10-60 seconds, be patient please. If it takes too
long to find your WIFI, please press down the reset button at the back of
the gateway for 6 seconds to reset the gateway and then you may start the
configuration from the start again.