USX-MOUNT XAS002-01 User manual

XAS002-01
INSTRUCTION MANUAL
If you have any questions along the way, just message
to us.We’re ready to help!
USA-B2
R

2
Before getting started, let’s check below lists to make sure it is just right for you!
1
2
3
4
Does your soundbar
(including accessories)
weigh MORE than
13 lbs. (6 kg)?
Do you have
all the tools
needed?
(NOT INCLUDE) Tape
Measure
CAUTION
Pencil Screw
driver
Electric
Drill
No? Perfect – you may continue.
Yes? This mount is NOT compatible.
Drywall with
wood studs? CAUTION:
CAUTION: DO NOT exceed the maximum weight
indicated. This mounting system is intended for use only
with the maximum weights indicated. Use with products
heavier than the maximum weights indicated may result
in collapse of the mount and its accessories, causing
possible injury.
Solid concrete ?
1/2 in.
(13 mm)
Socket
Wrench
Stud
Finder
5/32 in.
(4 mm)
Wood
Drill Bit
● Do not use this product for any purpose not explicitly specified by manufacturer
● Manufacturer is not responsible for damage or injury caused by incorrect assembly or use
Unsure?
Mail to us via Amazon.
3/8 in.
(10 mm)
Masonry
Drill Bit
HammerLevel
If you want to mount
on the wall, you
should know what
your wall made of.
CAUTION: PLEASE READ ENTIRE MANUAL PRIOR TO USE AND SAVE THESE INSTRUCTIONS
Max:
13 LBS
(6 kg)
Per fect !
DO NOT
install into
drywall alone Per fect !
Concrete Install
Wood Stud Install
!
!
!

WALL PLATE
FRONT VIEWRIGHT VIEW - Hook
3
8mm
[0.31in]
154mm
[6.06in]
88mm
[3.46in]
203mm
[8.00in]
406mm
[16.00in]
610mm
[24.00in]
FRONT VIEW 3-D
RIGHT VIEW - Hook
691mm
464mm
[18.27in]
48mm
87mm
[3.43in]
59mm
30mm
MAX:600mm
[23.62in]
MIN:150mm
[5.91in]
MAX:600mm[23.62in]
MIN:110mm[4.33in]
[1.89in]
[1.18in] [2.31in]
[27.19in]
Dimensions

WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts
are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact
Customer Service.
Never use damaged parts!
NOTE: Not all hardware included will be used.
4
Parts and Hardware for Brackets Installation
x1
x1
x1
M6x10mm
Bolt
x4
M6 Washers
x4
M5x6mm
Bolt
x2
x2
Hook Bracket (Left) Bracket (Right)
x1
Allen Key
x1
Wall plate (Left) Wall plate (Right)
Contact us message to us to have these
additional pieces shipped directly to you.
Concrete Wall Anchor
Ø10x50mm 2pcs
Lag Bolt M7x55mm 2pcs
Parts and Hardware
01
04 05 08 09
02 03
06 07
Lag bolt and concrete wall anchor (NOT INCLUDED)
Hook and Loop
!
x2

Spacers
Screws
M6x16mm
M8x20mm
M6x25mm
M8x30mm
M6
8x10mm
2.5mm
Washers
x4 x4
x4 x4
x4
x4
x4
Hardware for Soundbar Installation
x2
M5x8mm
a c
bd
h
eg
f
5

Tighten
Wall plate
No!
Ⅰ Remove all cables Ⅱ Take off the TV
from the mount
Ⅲ Remove the TV
brackets from your TV
TV
1 2
01
04
02
05
STEP 2 Disassemble Your TV from the Mount
STEP 1 Assemble Wall plate
6

No!
7
Tighten
Wall plate
Horizontal distance
of TV mounting holes
(Depend on your TV VESA)
06
07
08
05
STEP 3 Attach Brackets to Wall Plate
09
CAUTION: Check the horizontal distance of the TV before connecting the wall plate unit to the brackets.
!

8
STEP 4 Attach the Assembled Soundbar Mount and TV Brackets to Your TV
No!
Tips: No need to use washer (g) when using M8 screw (b/d).
Tips: Before attach the TV, check the vertical
distance of TV and wall plate.
Tips: Only the two threaded holes at
the bottom of the TV VESA are
allowed to install.
a c
g
fff
bd
e
a c
g
bd
e

TV
1 2
STEP 5 Hang the Whole Assembled Unit to the Mount
9
CAUTION: This step requires 2 or more people to complete.
!

Bottom
STEP 6 Assemble Your Soundbar with Soundbar Mount
6-1 Option 1 Install from the bottom with assembly holes.
Loosen
05
10
This installation method only applies to Soundbar with keyhole slots in the bottom.
hTighten
05
h

Back
6-2 Option 2 Install from the back with assembly holes.
Tighten 05
Loosen
05
h
11
This installation method only applies to the Soundbar with keyhole slots on the back.

This installation method is only for Soundbar without any keyhole slots, You can adjust the length of hooks and
use hook and Loop to secure the soundbar on the hook.
without holes
6-3 Option 3 Install the Soundbar without assembly holes or with keyhole slot
Loosen
05
Tighten 05
12
Hook and Loop

13
STEP 7 Hang and Secure the Soundbar Brackets
Tighten
CAUTION: This step requires 2 or more people to complete.
!

Centre line
CAUTION: Avoid potential personal injury or property damage!
● Drywall covering the wall, must not exceed 5/8 in. (16 mm)
● Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)
● Maximum horizontal space between fasteners: 24 in. ( 610 mm)
● Stud center must be verified
1. Locate your studs. Verify and mark the center of the stud by finding the stud edges using, a thin nail,
or an edge to edge stud finder.
2. Position the wall plate at your desired height and line up the holes with your stud center line. Level the
wall plate and mark the hole locations.
Stud
Finder
16"/24"
Level
Wall plate
1 2
Below step for Soundbar Mount single use on the wall
STEP 8 Option 1 Attach Wall Plate to Wall Wood Stud
14
!

3. Drill pilot holes using a 5/32 in. (4 mm) diameter drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 2.36 in. (60 mm). Be sure to drill into the center
of the studs.
4. Install wall plate using two lag bolts. Tighten the lag bolts only until they are pulled firmly against the
wall plate.
CAUTION: Improper use could reduce the holding power of the lag bolt.
DO NOT over-tighten the lag bolts.
5/32"
(4mm)
Level
Wall plate
Lag bolt
(Not included)
Please contact us and message to us to have these
additional pieces shipped directly to you.
Go to STEP 9 on PAGE 18.
2.36"(60mm)
3 4
15
!
!

3/8"
(10mm) 2.36"(60mm)
CAUTION: Avoid potential personal injury or property damage!
● Mount the wall plate assembly directly onto the concrete surface
● Minimum solid concrete thickness: 8 in. (203 mm)
1. Position the wall plate on the wall at your desired height. Level the wall plate and mark the hole
locations.
2. Drill two pilot holes using a 3/8 in. (10 mm) diameter masonry drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 2.36 in. (60 mm).
Level
Wall plate
1 2
STEP 8 Option 2 Attach Wall Plate to Solid Concrete Wall
16
!
!

Concrete Wall Anchor
(Not included)
3. Insert two anchors.
CAUTION: Be sure the anchors are seated flush with the concrete surface.
CAUTION: Improper use could reduce the holding power of the lag bolt.
DO NOT over-tighten the lag bolts.
4. Insert wall plate using two lag bolts. Tighten the lag bolts only until they are pulled firmly against
the wall plate.
Level
Wall plate
Lag bolt
(Not included)
Please contact us and message to us to have these
additional pieces shipped directly to you.
Please contact us and message to us to have these
additional pieces shipped directly to you.
3 4
17
!
!

Before putting soundbar, please try to pull the wall plate to make sure that it has been assembled
on the wall tightly.
STEP 9 Wall Plate Installation Integrity Test
18

Bottom
STEP 10 Assemble Your Soundbar with Soundbar Mount
10-1 Option 1 Install from the bottom with assembly holes.
19
This installation method only applies to Soundbar with keyhole slots in the bottom.
Loosen
05
hTighten
05
h

Back
10-2 Option 2 Install from the back with assembly holes.
Tighten 05
Loosen
05
h
20
This installation method only applies to the Soundbar with keyhole slots on the back.