USX-MOUNT SAS002-01 User manual

SAS002-01
INSTRUCTION MANUAL
R
USA-A0
If you have any questions along the way, just give us a
mail to [e-mail].
We’re ready to help!

2
Before getting started, let’s check below lists to make sure it is just right for you!
1
2
3
4
Does your soundbar
(including accessories)
weigh MORE than
13 lbs. (6 kg)?
Do you have
all the tools
needed?
(NOT INCLUDE) Tape
Measure
CAUTION
Pencil Screw
driver
Electric
Drill
No? Perfect – you may continue.
Yes? This mount is NOT compatible.
Drywall with
wood studs? CAUTION:
CAUTION: DO NOT exceed the maximum weight
indicated. This mounting system is intended for use only
with the maximum weights indicated. Use with products
heavier than the maximum weights indicated may result
in collapse of the mount and its accessories, causing
possible injury.
Solid concrete
1/2 in.
(13 mm)
Socket
Wrench
Stud
Finder
5/32 in.
(4 mm)
Wood
Drill Bit
● Do not use this product for any purpose not explicitly specified by manufacturer
● Manufacturer is not responsible for damage or injury caused by incorrect assembly or use
3/8 in.
(10 mm)
Masonry
Drill Bit
Hammer
Level
If you want to mount
on the wall, you
should know what
your wall made of. ?Unsure?
Mail to
[e-mail]

FRONT VIEW 3-D
WALL PLATE
FRONT VIEW
RIGHT VIEW - Hook
RIGHT VIEW - Hook
3
8mm
[0.31in]
691mm
[27.19in]
464mm
[18.27in]
48mm
[1.89in]
87mm
[3.43in]
59mm
[2.31in]
30mm
[1.18in]
154mm
[6.06in]
88mm
[3.46in]
203mm
[8.00in]
406mm
[16.00in]
610mm
[24.00in]
MAX:600mm
[23.62in]
MIN:150mm
[5.91in]
MAX:600mm[23.62in]
MIN:110mm[4.33in]

WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts
are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact
Customer Service.
Never use damaged parts!
NOTE: Not all hardware included will be used.
4
Parts and Hardware for Brackets Installation
x1
x1
x1
M6x10mm
Bolt
x4
M6 Washers
x4
M5x6mm
Bolt
x2
x2
Hook
Bracket (Left) Bracket (Right)
x1
Allen Key
x1
Wall plate (Left) Wall plate (Right)
Concrete Wall Anchor 2pcs
Lag Bolt M7x55mm 2pcs
Contact us and mail to
[e-mail].
to have these additional pieces
shipped directly to you.

5
Spacers
Screws
M6x16mm
M8x20mm
M6x25mm
M8x30mm
M6
8x10mm
2.5mm
Washers
x4 x4
x4 x4
x4
x4
x4
Hardware for Soundbar Installation
x2
M5x8mm

Tighten
Wall plate
No!
1 Disassemble Your TV from the Mount
Ⅰ Remove all cables Ⅱ Take off the TV
from the mount
Ⅲ Remove the TV
brackets from your TV
TV
1 2
6

2 Attach Brackets to Wall Plate
Tighten
Wall plate
No!
Tips: Check the horizontal distance of the TV before
connecting the wall plate unit to the brackets.
Horizontal distance
of TV mounting holes
(Depend on your TV VESA)
7

No!
3 Attach the Assembled Soundbar and Brackets Unit to Your TV
Tips: No need to use washer (g) when using M8 screw (b/d).
Tips: Before attach the TV, check the vertical
distance of TV and wall plate.
8

TV
1 2
4 Hang the Whole Assembled Unit to the Mount
5 Hang the Hooks
Tighten
9

6 Put on the Soundbar
Tighten
Loosen
10
Soundbar
If the width of your soundbar bottom is more than 88mm ( 3.46 in ), please follow with below step.
Otherwise, put soundbar on the hook directly.
Option 1 Back
Screw Hole
Option 2 Bottom
Screw Hole

Centre line
CAUTION: Avoid potential personal injury or property damage!
● Drywall covering the wall, must not exceed 5/8 in. (16 mm)
● Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm)
● Maximum horizontal space between fasteners: 24 in. ( 610 mm)
● Stud center must be verified
1. Locate your studs. Verify and mark the center of the stud by finding the stud edges using, a thin nail,
or an edge to edge stud finder.
2. Position the wall plate at your desired height and line up the holes with your stud center line. Level the
wall plate and mark the hole locations.
Again, find another wood stud
16"/24"
Level
Wall plate
11

3. Drill pilot holes using a 5/32 in. (4 mm) diameter drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 2.36 in. (60 mm). Be sure to drill into the center
of the studs.
4. Install wall plate using two lag bolts. Tighten the lag bolts only until they are pulled firmly against the
wall plate.
CAUTION: Improper use could reduce the holding power of the lag bolt.
DO NOT over-tighten the lag bolts.
2.36"(60mm)
5/32"
(4mm)
Level
Wall plate
12
Lag bolt
(Not included)
Go to STEP 3 on PAGE 15.
Please contact us and mail to
[email protected] to have these
additional pieces shipped directly to you.

3/8"
(10mm) 2.36"(60mm)
CAUTION: Avoid potential personal injury or property damage!
● Mount the wall plate assembly directly onto the concrete surface
● Minimum solid concrete thickness: 8 in. (203 mm)
1. Position the wall plate on the wall at your desired height. Level the wall plate and mark the hole
locations.
2. Drill two pilot holes using a 3/8 in. (10 mm) diameter masonry drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 2.36 in. (60 mm).
Level
Wall plate
13

Concrete Wall Anchor
(Not included)
3. Insert two anchors.
CAUTION: Be sure the anchors are seated flush with the concrete surface.
CAUTION: Improper use could reduce the holding power of the lag bolt.
DO NOT over-tighten the lag bolts.
4. Insert wall plate using two lag bolts. Tighten the lag bolts only until they are pulled firmly against
the wall plate.
Level
Wall plate
Lag bolt
(Not included)
14
Please contact us and mail to
[email protected] to have these
additional pieces shipped directly to you.
Please contact us and mail to
[email protected] to have these
additional pieces shipped directly to you.

Before putting soundbar, please try to pull the wall plate to make sure that it has been assembled
on the wall tightly.
15

Tighten
16
Hang the hooks and tighten the bolts.

Loosen
Soundbar
17
If the width of your soundbar bottom is more than 88mm ( 3.46 in ), please follow with below step.
Otherwise, put soundbar on the hook directly.
Tighten
Option 1 Back
Screw Hole
Option 2 Bottom
Screw Hole