USX-MOUNT XAS502 User manual

XAS502
INSTRUCTION MANUAL
If you have any questions along the way, just message
to us. We’re ready to help!
R
USA-C1

Before getting started, let’s check below lists to make sure it is just right for you!
1
2
3
Does your
assembled stand
(including accessories)
weigh MORE than
11 lbs. (5 kg)?
Do you have
all the tools
needed?
(NOT INCLUDE) Tape
Measure
CAUTION
No? Perfect – you may continue.
Yes? This mount is NOT compatible.
CAUTION: DO NOT exceed the maximum weight
indicated. This mounting system is intended for use only
with the maximum weights indicated. Use with products
heavier than the maximum weights indicated may result
in collapse of the mount and its accessories, causing
possible injury.
11 LBS
(5 kg)
!
2
CAUTION: PLEASE READ ENTIRE MANUAL PRIOR TO USE AND SAVE THESE INSTRUCTIONS.
!
Open-end wrench
Never let children climb on product or play with product.
Do not sit or stand on product.
Do not fasten a speaker that is heavier than the recommended load rating to the mount.
Improper installation may cause property damage and/or personal injury, so the installation must be
done by two qualified contractors. The manufacture is not liable for damage or injury caused by incorrect
mounting, assembly or use.
Improper handling can result in cuts and lacerations.
Pictures for reference only, subject to our available products.
Keep this instruction for future reference.

3
Dimensions
TOP VIEW
FRONT VIEW SIDE VIEW 3-D
SPEAKER ATTACHMENT UNIT FRONT VIEW

M6 Carpet Nail
8 pcs
4
WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts
are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact
Customer Service.
Never use damaged parts!
NOTE: Not all hardware included will be used.
Parts and Hardware for STEP 1
Parts and Hardware
!
M4X4 bolt
2pcs
M6X12 bolt
2pcs
M6X10 bolt
2pcs
a--M4X30 bolt
2pcs
b--M6X30 bolt
2pcs
c--M6X24 key
hole bolt 2pcs
d--M6 Butterfly Nut
2pcs
e--M4 washer
2pcs
f--M6 spacer
2pcs
01 02
03 04

M6 Carpet Nut
8 pcs
Parts and Hardware for STEP 2
5
Base
2pcs
Bottom tube
2pcs
Adjusting tube
2pcs
Speaker attachment
unit 2pcs
Allen key
1pc
07
06
08 10
09
05
Velcro x6

1-1 Insert bottom tube into base , then fasten bolt by using Allen key .
STEP 1 Assemble Product
6
02
07
02 07
10 08
10
08
Adjustable foot
Option: If the stand is placed on carpet, spin to
loosen and remove the rubber feet,
install the carpet nail and screw to
the end, then use the nut to tighten
the nail.
08
04
05
04
05

1-2 Insert Adjusting tube into bottom tube and use Allen key to fasten bolt .
7
07
03
07 03
10
09
09
10

8
Wire
1-3 Attach the Speaker attachment unit to the Adjusting tube and fasten it with bolt .
07
01
01
06
06 09
09
Installation method of wires:
Method 1: Pass the wire through the internal connection of
the product;
Method 2: Fix the wire directly on the surface of the product
tube with Velcro.
Wire
Figure 1 Figure 2
Velcro

9
Step 2 Attach speaker to assembled stand
Option 1: According to your speaker's installation hole, choose bolt a/b,washer(e) and spacer (f) (as
shown in Figure 1 and 2) to attach it.Then plug the wires.
a
f
Figure 1
a
f
e
b
f
Figure 2
b
f
eM4 bolt
M6 bolt
M4 bolt
M6 bolt
For inset hole: Use bolt (a/b), washer (e) and spacer (f) to attach
the speaker. M4 washer (e) is only for M4 bolt (a) installation,
while no washer is required for M6 bolt (b) installtion.

10
c
d
Option 2: For speaker with a key hole,attach key hole bolt (c) to the speaker attachment unit with
butterfly nut (d).
06
06

Place speaker on stand with key hole bolt (c) inserted in the key hole, then tighten the butterfly nut (d)
and plug the wires.
11
d

MIN:793mm
[31.2in]
MAN:1024mm
[40.3in]
Tighten
Loosen
12
Step 3 Height Adjustment
Loosen the handle, and adjust the tube to desired height,then tighten the handle.
09