UTEPO UTP801P User manual

UTP801P
No need for additional power supply;
High-Definition transmission up to 35m;
Suggested resolution up to 1024*768;
Using CAT5/5E/6E cable;
Synchronous transmission, no time delay;
Compatible with VGA, SVGA, XGA, SXGA etc;
Dial adjustment, easy to use;
Plug and play, simple installation;
I
ron metal outer shell, super interference rejection;
Panel Diagram
Installation Procedure
单路无源双绞线 拨 码V G A传 输 器
The product is single channel passive UTP VGA balun which allows transmission of
high resolution and high fidelity VGA video signal over UTP cable.It should be used in
pair including a VGA transmitter and receiver. The device is plug and play, no need for any
driver software.
Features
Transmitter
4
Receiver
Typical Application
RJ45 ADJ
1 3
VGA IN PUT
2
RJ45 ADJ
5
123
VGA OUT PUT
Please switch off the computer before installation,or else installation with power may
damage devices;
Make sure the UTP cable to be used is available;
Connect the computer with VGA transmitter via VGA cable;
Connect the VGA receiver with remote monitor;
Connect the VGA transmitter and receiver via UTP cable;
Open the computer and use dial adjustment for best image.
NO. Component Description
Grounding Terminal
3
1
2RJ-45
Dial Adjustment
4
5
15pin HD15 female
For grounding
RJ-45 plug
Please refer to “Dial Adjustment Method”
VGA input,to connect computer via VGA cable
VGA output,to connect remote monitor directly
Single Channel Passive VGA Extender
Single Channel Passive VGA Extender
2
1
Monitor
UTP CAT5/5E/6 Cable
PC
Receiver
Transmitter
Monitor
15pin HD15 female
(1)
(6)
(5)
(4)
(3)
(2)
Please follow the next installation steps:

Single Channel Passive VGA Extender
Channel
Video
Properties
Function
Video Input
Compatible with
Synchronous Signal Band
Signal Transmission Band
Surge Protection
ESD
Reliability MTBF
Physical
Properties
Size（LWH）
Outer Shell
Color
N.W.
Environmental
Operation Temperature
Storage Temperature
Transmitter：111g Receiver：110g
Relative Humidity
Specification subject to change without notice.
Dial Adjustment Method
Troubleshooting
Make sure the installation is according to the manual.
Specification
UTP Cable Connector
DDC
Adjustment
Protection
Transmission Distance Make sure the real distance not exceeds the allowed transmission distance,
the real maximum distance is relative to quality of signal source and cable.
Please use the adjustment switches if no image.
Restart the computer.
Replace the device at question by a normal working one.
If any instability of image using laptop,please check if the device is grounded.
If the trouble still exists,please contact your vendor.
Transmitter
T:gear 1 T:gear 2
There are 2 gears on the transmitter:
Receiver
There are 3 gears on the receiver:
R:gear 1 R:gear 2 R:gear 3
Please firstly confirm and fix the gear of transmitter,
then change the gear of receiver for satisfying image.
Acquiescent gear：
Method
T:gear 1 R:gear 1
Check if both ends of UTP cable conform with 568A or 568B at the same time.
Dial Adjustment
Item Parameter
4
3
2KV 10/700us Per IEC61000-4-5
15pin HD15 female
Single Channel
Contact Discharge:6000V
Air Discharge:8000V
IEC61000-4-2 1995
>10000h
85*64*28mm
Iron Metal
Black
0 ~5 5℃ ℃
0%-95%(non-condensing)
<120MHz(-3db)
1K-200KHz
VGA、SVGA、XVGA WS、XGA、UXGA、WSXGA etc.
RJ-45
Support DDC2
please refer to “Dial Adjustment Method”
35m(maximum)
-20°C~70°C
Single Channel Passive VGA Extender
Pin Diagram
video
video
Power -
Power -
Power -
Power +
Power +
Power +
1
2
3
4
5
6
7
8
EIA/TIA 568A EIA/TIA 568B
Pin Diagram
video
video
Power -
Power -
Power -
Power +
Power +
Power +
1
2
3
4
5
6
7
8
Attention:
Make sure if one end is EIA/TIA568A,the other end should also be
B-
G -
Code
G +
R -
Code
R +
1
2
3
4
5
6
7
8
B+
B-
G -
Code
G +
R -
Code
R +
1
2
3
4
5
6
7
8
B+
Package Contents
(1 pcs)
(1 pcs)
(1 pcs)
VGA Transmitter
VGA Receiver
VGA Cable (M-F)
Application manual
RJ 45 PIN Diagram
(1 pcs)