UTEPO USP2108 User manual

Feature
12
● Standard : IEC61643-21:2000 standard
● Protection: Ethernet signal(bandwidth ≤ 100Mbps);
● Feature: Multi-level over voltage protection, large capacity discharge current, low limiting
voltage, quick reacting time, low inserting loss;
● Grounding mode: Extending line to the ground;
● Design :Clear mark, easily recognized, aluminum shell, support desktop or on-wall installation.
;
The surge protector is an 100M ethernet signal surge protector based on IEC61643-21:2000
standard. The equipment nominal voltage is 5V, maximum continuous running voltage is 6V,
limit voltage is less than 20V. It features multi-level protection, large maximum discharge
current, low limiting voltage, quick reacting time, low inserting loss etc..It is adapted to
Ethernet switch, concentrator, network card, computer signal and power over voltage
protection, exempt from the damage caused by reacting over-voltage, operating over-
voltage and static electricity discharge etc.. It is widely used in conference system, security
surveillance system etc..used in meeting system, security surveillance and office ethernet
project.
Notice
1) Please make sure that the surge protector output is connected with the protected equipment.
The connection should not be reversed!
2) The surge protector doesn't work if not strictly abide by the grounding instructions .
1)
standards;
2) Please ensure that the connection is stable;
3) Please ensure that the grounding cable of surge protector is connected with the main grounding
cable in the room as short as possible.
Before inserting protector into system, please make sure the grounding grid reach the
Please follow the installation step
Please check the following items before installation, if it s missing please contact the dealer.
Multichannel ethernet signal surge protector 1pc
Hanger 1pair
User manual 1pc
'
Installation Step
Application
ethernet optical
transceiver
IP camera
Dome camera
Cat5/5e/6 cable
NVR
PTZ Camera
Dome camera
Fiber
Board Diagram
Multichannel Network Signal Surge Protector
Notice
1)Protector possess signs of input(IN), output(OUT). Please ensure that the output end is
connected with the protected equipment, otherwise it will cause the damage of surge protector.
2)Please check the plug if the consumption increases. You can either re-connect it or replace the
protector.
3) Please don't un back the component personally
Front board Back board
Grounding
8Channel Ethernet Signal Surge Protector
IN (L ine)
Signal input
24Channel Ethernet Signal Surge Protector
OUT ( Equip )
Signal output
Signal output
IN( Lin e) IN( Lin e) IN (Li ne) I N(L ine) I N(L ine )
OUT (Eq uip ) OUT( Equ ip) O UT( Equ ip) OU T(E qui p) OU T(E qui p)
Front board Signal input
Back board
Multichannel Ethernet Signal Surge Protector
Grounding
Surge protector
Multichannel Ethernet
Signal Surge Protector
Switch

连接接口
Specification
34
Notice:
product are subject to change without prior notice
连接接口
Trouble shooting
Check Protector
Use multi-meter “Ω×10” grade to measure the protector's resistance between input
and output core wires. The value should be less than 4.7Ω . If it is too high or
malfunctions, please replace the protector.
Use multi-meter “ Ω × 1M” grade to measure core wire's resistance to the shell,
which is about 400kΩ; the resistance for the cable to the ground and shell to the ground
should be infinite. if the measured value is incorrect, please replace the protector.
RJ 45 making method
pin color
white/green
green
blue
white/orange
white/blue
white/brown
orange
brown
1
2
3
4
5
6
7
8
pin color
1
2
3
4
5
6
7
8
white/green
green
blue
white/orange
white/blue
white/brown
orange
brown
EIA/TIA 568A EIA/TIA 568B
When choose RJ-45 make sure if one end is EIA/TIA568A,the other end should also be EIA/TIA568A.
When choose RJ-45 make sure if one end is EIA/TIA568B,the other end should also be EIA/TIA568B.
Notice
Item Description
Product Mode
Nominal Operational
Voltage
Max Continuous
Operational Voltage
Nominal
Discharge Current (8/20us)
Max
Discharge Current (8/20us)
Voltage
Protection
(10/700us)
Insulation Resistance
Inserting Loss
Bandwidth
Response Time
Protection Cable
Protection Route
Working Temperature
Storage Temperature
Humidity(non condense)
Size
Material
Weight
MTBF
Color
Ethernet
Signal
Environment
Structure
Stability
Aluminum Irony
Black Black
8 ports 24ports
Multichannel Ethernet Signal Surge Protector
Multichannel Ethernet Signal Surge Protector
Instruments to be used: wire crimper, network tester. Wire sequence of RJ45 plug should conform
with EIA/TIA568A or 568B.
1) Shuck off about 2cm long the insulating layer, and bar the 4 pairs UTP cable;
2) Depart the 4 pairs UTP cable and straighten them;
3) Line up the 8 pieces of cables per EIA/TIA 568A or 568B;
4) Cut out 1.5 cm cable wrap and leave the bare wire;
) Plug 8 cables into RJ45 plug, make sure each cable is in each pin;
5
6) Then use wire crimper to crimp it;
7) Follow the 5 steps above to make the another end, following the same sequence of the first plug;
8) Using network tester to test the cable whether is working.