UWS LADDERRACK User manual

UWSTA.COM •NEED ASSISTANCE? •8 7 7. 2 8 7. 8 6 3 4 •UWS-LADDERRACK-INS-RA •PAGE 1
Parts List
2Ladder rack
4Bolt, 5/16"
16 Washer, 5/16"
12 Nut, 5/16"
4U-bolt, 5/16"
2Angle bracket
INSTALLATION MANUAL
Tools Required
Drill Drill bit, 5/16"
Ratchet Socket set
Tape measure --
Level of Difficulty
Easy
Product Photo
UWS-LADDERRACK
Maintenance
For polished, gloss and other smooth
finishes, polish may be used to clear
small scratches and scuffs on the finish.
Mild automotive detergent may be used to
clean the product. Do not use dish detergent,
abrasive cleaners, abrasive pads, wire
brushes or other similar products that
may damage the finish.
DANGER
Danger of explosion. Do not use this product for storing or transporting flammables,
explosives, hazardous materials or hazardous waste, such as containers of gasoline,
solvents, gun powder, dynamite, propane tanks, acetylene tanks and cutting torches.
WARNING
Never exceed the vehicle manufacturer's recommended capacity.
Ladders and other cargo must be properly secured at all times. Damage will occur from road
shock and vehicle vibration if the ladder and / or materials are not secure. Bouncing and side-
to-side motion of an improperly secured ladder can cause wear and weaken the racks. Using
damaged racks could lead to a structural collapse and could result in serious injury or death.
This product can reduce the driver's ability to clearly see roadways, vehicular or pedestrian
traffic and other objects through the rear and side windows of the vehicle, which may cause
an accident. Extra precaution should be taken when driving a vehicle with this product.
Do not interfere with factory-installed safety equipment.
NOTICE
Before you begin installation, read all instructions thoroughly.
Proper tools will improve the quality of installation and reduce the time required.
To help prevent damage to the product or vehicle, refer to the torque
specifications when securing hardware during the installation process.
Do not use this product for purposes other than those
for which they were designed. Never modify this product.
Consult your dealer if you have any questions regarding
the installation, operation, use and limits of this product.
Treat or seal all fasteners and exposed metal in any
holes drilled in vehicle to prevent corrosion.
Product Registration and Warranty
CURT Group stands behind our products
with industry-leading warranties. Provide
feedback and help us to improve our
products by registering your purchase at:
warranty.curtgroup.com/surveys
Torque Specifications*
Metric
M6 bolt 3 ft-lbs.
M8 bolt 7 ft-lbs.
M10 bolt 16 ft-lbs.
M12 bolt 28 ft-lbs.
SAE
1/4" bolt 3 ft-lbs.
5/16" bolt 7 ft-lbs.
3/8" bolt 16 ft-lbs.
7/16" bolt 20 ft-lbs.
1/2" bolt 28 ft-lbs.
* Above specifications are general guidelines.
If purchasing hardware use the torque
specifications provided with that hardware.

UWSTA.COM •NEED ASSISTANCE? •8 7 7. 2 8 7. 8 6 3 4 •UWS-LADDERRACK-INS-RA •PAGE 2
Step 1
WARNING
Before drilling into your truck bed, check under
your vehicle to ensure the drill location does not
puncture, cut or obstruct any brake or fuel fluid
lines, electrical wires, fuel tanks, etc. Precaution
must be taken that all fasteners near the fuel
tank do not create the possibility of fuel tank
puncture or other damage during a collision.
Drill two 5/16" holes in the side rail lip.
Bolt the U-bolt around the rack and
through the side rail lip (figure 1).
Loosely attach the U-bolt to
the mounting bracket (figure 2).
Ensure the ladder rack upright is vertical.
Position the angled bracket on the floor of the
truck bed and mark holes for mounting (figure 3).
Firmly attach the mounting bracket to the floor
of the truck bed. Tighten all hardware. Repeat
for the other upright (figure 4).
Step 2
CAUTION
Ensure all knobs, bolts, screws, straps and
locks are firmly secured before every trip.
Periodically re-tighten and inspect all components
for signs of wear, corrosion and fatigue.
WARNING
Ladders and other cargo must be properly
secured at all times. Damage will occur from
road shock and vehicle vibration if the ladder
and / or materials are not secure. Bouncing and
side-to-side motion of an improperly secured
ladder can cause wear and weaken the racks.
Using damaged racks could lead to a structural
collapse and could result in serious injury or death.
With the ladder racks installed, periodic
inspections should be performed to ensure
all mounting hardware remains tight.
To protect your investment, see the
'Maintenance' section on page 1.
Congratulations on the installation
of your new UWS ladder racks.
Figure 4Figure 3Figure 2Figure 1